Counting matching models…
Misc. Info: The print-in-place ring mechanism has two versions with different tolerances. Make sure your elephants foot compensation is set properly to prevent the hinge from seizing. The loose (original) version has a minimum gap size of…
The model can is set up to be printed in multiple pieces separated by color. An openSCAD file for remixing purposes. Several different variations are available: V2 Torsos V2 torsos have 2 eye pieces that individually insert after…
The main stand is separated from the peg that the model mounts to. I recommend slicing the peg lengthwise to print, then gluing the halves together afterwards. Some post-processing will likely be needed to get a good fit. Two variations…
These models were made with dimensions found on Wikipedia, and are intended for prop usage. It is not recommended to load them. Add color with a height-based material change, or with the cut tool Additional cartridge types available by…
The Alicorn from Ace Combat 7, complete with a chess piece stand. This model has 2 variants, with and without the fins extending from the hull. I recommend printing the non-finned version on FDM printers, and the Finned version with SLA.…
Testudo the Diamondback Terrapin is the mascot of the University of Maryland. These models are replicas of statues found across campus. Both the classic and modern versions are shown here. A mid-print pause was used to change the color…
This model was designed in openSCAD. Source file included for your remixing convenience.
Parts: 4 Different versions are available: Lighthouse_Elevator_Hollow has a hollow central shaft Lighthouse_Elevator_Filled has a filled central shaft for greater structural support, and is more suitable for down-scaling Lighthouse Tower…
Solids of constant width maintain the same distance from top to bottom no matter the orientation. This allows them to roll smoothly like spheres. A few sample solids are provided. Additional shapes can be generated in the OpenSCAD file by…
Tetris pieces designed in openSCAD. Source file included for your remixing convenience
This tool is recommended for use only on soft materials! How to Use: Mount the solid front part of the tool at the end of a sharp outer edge. The 90 degree inner angle should fit against the sharp edge of the material. Press razor blade…
Recommended Settings (See sliced file): Material: PETG (PLA may soften if used outdoors) Brim: 5mm Special settings for sliding clamp: 3 perimeters, 6 top and bottom solid layers Assembly Instructions: V1: Run a ¼-20 or M6 tap through the…
Recommend 0.1 layer height, with height color change Other designs available by request
Parts: 4 different versions are provided, which contain various levels of detail: "Excalibur Campus Full" contains the main tower and its power regulators, as well as the surrounding generators and solar panel arrays "Excalibur Campus…
Changes: 11/18/2023 - added mantlet part and updated instructions 1/2/2023 - original upload Parts: The cannon support is fixes the cannon the in forward position The muzzle brake looks more accurate to real life and directly replaces the…
Clarinets of the Boehm (French) and Oehler (German) systems have different dimensions, which make their mouthpieces incompatible. These adapter barrels allow a mouthpiece from one system to mounted on a clarinet of a different system. The…
Parts: The side plate replaces two sloped parts on the left side of the cannon The muzzle brake replaces the large cylinder part halfway down the length of the barrel The turret parts replace the small slope pieces that make up the front…
Parts: Mantlet and MG port: provide more photorealistic geometries that more closely resemble the real objects Barrels: 6mm barrel pieces are closer to the real-life scale. They are available in 19 and 38mm lengths, depending on what your…
This device helps you size the studs and holes on your lego-compatible designs. The feature size increases in a series from left to right so you can find the dimensions to produce a perfect fit. Want to test a dimensional range outside of…
Playing just the upper half of a clarinet can be fun, except it presents the challenge of maintaining good intonation in the lower note range, and keeping the instrument steady with just one hand. This device aims to fix both of those…
Parts: Sprocket mount: based on the existing 2x2 brick with a hole, except the position of the hole is 1.5mm lower on the part, which relieves enough tension from the tracks for them to run smoothly. The L and R versions are identical…
Since the Collapse, these pistols have been retooled several times to boost their firepower. A worn inscription reads, "To Victor, from Sigrun." Disclaimer: this model is a prop gun that does not shoot anything Extra tools and hardware…
An ornamented version of Drang, from Destiny 2. Disclaimer: this model is a prop gun that does not shoot anything Please refer to the original model for hardware, printing, and assembly instructions: Extra Hardware: In addition to what is…
Disclaimer: Exercise caution and use only in outdoor or open spaces. Designer is not responsible for personal injury, property damage, or hurt feelings. You will need the following extra hardware: 1x 0.75in ID PVC pipe (1-1/16in or 27mm…
An Earth artifact, refashioned to suit the Emperor's modest tastes. Disclaimer: this model is a prop gun that does not shoot anything Please refer to the original model for hardware, printing, and assembly instructions: Extra Assembly…
This model was made for Cobi set 2576. The parts may be compatible with other similar Cobi Panzer IV sets, but that has not been tested. Slicing Instructions Import the parts to PrusaSlicer their original orientation. the side skirt STLs…
These are all currently available results.
