Counting matching models…
A wedge for the Sunlu filament dryer S2 to open the case a little to let the humidity out (around 5mm). I printed it without support and it turned out fine. Make sure to print it with a heat-resistant material for your use case. I used…
This is a simple and small case for the ESP8266 Lolin V3. It is completely screw-less and can be opened and closed via clicking together. (Sometimes the ESP's USB connector is to far away from the cover. Just break the the holder inside…
I found a nice video on YT about a polycarbonate panel with a drilled hole for any 15 cm air exhaust. The missing thing were the parts to connect the hose with the panel. So there they are, modeled from scratch. I used the sliding…
This model is a customized version of the Pi 4 Snapfit 60mm fan case from @ash. I just wanted to have the cool infill look also on a case for the Raspberry Pi3, so I adjusted the holes for the plugs. There is also a 60mm and a 40mm fan…
The base mount will be supported by two of the holders. All of them are hold in place by M5 screws and hammer nuts. Both holders need to be in place, before the bigger part, other wise the holder can not be screwed on your frame. Also put…
This is a simple and small case for the ESP8266 Lolin V3. It is completely screw-less and can be opened and closed via clicking together. (Sometimes the ESP's USB connector is to far away from the cover. Just break the the holder inside…
The duct sits directly on the heat sink of the CPU of a Futro S920. For power I used the fan connector on the board. (And a left-over silent-adapter from a Noctua fan, to silent it a little.
After #GPN23 I was in need to remove the wrist band without any damage and came up with this idea of two little sliders: The Bändlbefreier How to print Print at least two of them for band removal. I used a layer height of 0.15 mm, 0.2…
This mount contains a Raspberry Pi 2/3/4 Mount and a place for a SSD or slim HDD below the PI. I used M2.5 screws to hold the PI in place and printed the model with the top side down on the bed. On the four legs, there are holes to mount…
I'm using Nema 23 motor for my current Hypercube Evolution build, so I changed the Z motor mount as well as the Z Nut to match the Dimensions of the bigger motors. Print Settings Printer: CTC Rafts: No Supports: Yes Resolution: 0.2…
I needed this tall foot to get some space for fans and components on my Hypercube Evolution. For the screws M5 are used and the squash balls are from Amazon (Double Yellow) Print Settings Printer: Hypercube Evolution Rafts: No Supports:…
I made this wall mount to fit a Lenovo Tab M10 in it. It is integrated in the wall and holds the tablet firmly in place. To hide the tablet borders a wooden frame will be magnetically attached to the mount. It's split into two parts to…
Got the idea from this and adjusted it to mount on my Hypercube Evolution printer. The frame mount fits an 3030 extrusion T-profile with 8mm gap. The parts are press-fit together and still allow a little rotation of the webcam. Print…
An simple holder for the Davy Jones Cluebox from iDventure . The cluebox can be placed in it and the top face is more visible.
Want to personalize your round Sonoff buttons? This model might be for you! Assembly: Screw together the two parts of the pusher and put the top of the base between them Fit the button in the bottom base part Screw the top and bottom part…
This ID card holder is designed to take up as little space as possible while still keeping your card and accessories secure, even when moving or swinging around. It can hold: An employee ID card in standard credit-card format A small key…
The pi mount was designed for a simple NAS system based on a PI4 and this Dual HDD/SSD case. The case has an integrated RAID controller, so one drive gets mirrored with out the knowledge of the Raspberry PI and prevent data loss through a…
This stand holds one NeoPixel Jewel in place. I put some doublesided tape on the jewels bottom to make them stay in the holder. Print Settings Printer Brand: Creality Printer: CR-10S Rafts: No Supports: Yes Resolution: 0.2 Infill: 20…
Had an 40 mm fan laying around, so I adjusted the case to fit a 40 mm fan. Also make sure the set the top and bottom layer to 0 and a 2D infill in the slicer to get the look-through look. The print in the images has the gyroid infill (not…
This raiser will lift up a Balconera plant pot 20cm from the ground. With that the plants are better accessible. Also they are not directly sitting in the probably cold floor. With a pair of them placed around 20cm away from the sides the…
This is the final model of the remixed thing, which replaces my bike bottle holder with a holder for a powerbank for longer tours and stress-free positioning. The holder is made for the Anker PowerCore 20100mAh . Also a little hole at the…
This is a extrusion mount for a 5" LCD touchdisplay from Joy-It . It also holds some cutouts for letting cable through the side (for the stepper above). The red dice is only shown on the images, its not included in the stl files. I'm…
Das ist das Model was ich für einen selbstgießenden Blumentopf entworfen habe. Über eine kleine Pumpe wird Wasser von unten nach oben gepumpt um die Orchidee oben automatisch gießen zu können. Mehr habe ich in meinem Blog-Artikel…
A holder for the PTFE tube at the hotend mount of my Hypercube Evolution. It self-aligns with the screwhole on the blower. Print Settings Printer: Hypercube Evolution Rafts: No Supports: No Resolution: 0.15 Infill: 15% Filament: extrudr…
This is my custom mount for a MKS SKR 1.3 Board on my Hypercube Evolution. It can also hold a raspberry PI, on which I run OctoPrint on. The two boards are connected over a direct serial connection via GPIO. I took the step on controll…
Mounts for the bed cablechain on my Hypercube Evolution. The frame mount is modeled to fit a 3030 extrusion and the mount on the bed fits a 2020 extrusion. The cable chain has a width of 200mm. Print Settings Printer: Hypercube Evolution…
I designed and printed this to prevent some cables on my Hypercube Evolution to scrap on sharp extrusion edges, when laying the printer down. They height is 15mm on a 25mm square base. Print Settings Printer: Hypercube Evolution Rafts: No…
This replaces the bottom cover for toniebox with one that has a slot for MicroSD extension cable. I added the MAC as well as the Tonie-id to the outside of the cover within the slicer. The compatible inner battery part with MicroSD reader…
A simple stand for the frischluft.works project . It tilts the box around 20° to make the display easier to see, if its placed on a lower cupboard. Print Settings Printer: Hypercube Evolution Rafts: No Supports: No Resolution: 0.15…
The labels requires you to be able to do a two-color print. The filament in the purge tower is 0.25 gram to keep the waste somewhat sane. 3 simple steps for this model: Load the 3mf file in your slicer Change the text and font with the…
Just a quick and simple print to secure a bottle on a leg of a LACK table. Just clip it around the table and slide it over the bottle top. --- Proofed by Chaos
These are all currently available results.
