Counting matching models…
OpenSCAD model to simply create a cap with a few measurements. 2025-12-24 update: I've added a replacement nozzle that can be screwed to the tube and a screwable cap to just close the tube without the nozzle. Of course you can buy…
The uploaded models measure 10x10mm and have a 5x5x2mm gap for the pcb and holes for 3mm screws. The asymmetric ones are 7x10mm and have a 5x3x2mm gap. The asymmetric code can also create the slotted block if you use a 7x3x2mm gap.…
For a long time I was unhappy about how may pan / pot lits were stored. I thought this is a woodworking project till I saw https://www.printables.com/model/796854-cabinet-organizers. But this is only was a single size thing. I thought…
I've seen other pen holders and I didn't like the spring mechanisms that presses the pen down to the drawing area. (rubber bands, spring in the pen, …) My holder uses meander springs that are printed with the part. This spring can be…
Largest star: 190mm Smallest star: 50mm
I found some wooden sticks in the supermarked intented for growing plants. Nice, lets try something different. For another project I needed a circus tent, but everything also would be usable for platonic solics, too. (see wikipedia:…
Just another ruler guide with printed threads. The slot is partly in the thread so the ruler can be fixed with the nut. I used it with M10 metal washer even if I've added a washer to the model. Thread diameter of screw shrinked by 0.3 mm…
Replacement of the insert plate for 90° cuts. The insert plate is slightly thicker (3.5mm) than the original part as the original was below the surface of the aluminium plate. The angled part of the screw hole was slightly to small and I…
Outer Diameter: 80mm Modeled with OpenSCAD.
On the Ender5 the display is mounted on the side and takes quite some space. To reduce the width of the Ender5 I decided to mount the display partly inside the Ender5 cube. The display can only get so far into the cube that it does not…
The tool holder is 20mm wide, thus it fits on the printers profile. In my print on Allen key hole is missing, but its part of the model. The holder is mounted with 2 M3 screws and T-Nuts in the first and last compartment of the tool holder.
If you use the gauge that with X mm scale then you will cut strips with the with of the gauge (left picture). If you use the gauge without blade thickness, then you will cut away xx mm from your wood (Right picture). You can also combine…
The hopper is modeled upside down.
The holder is intended to hold some QR-Codes.
The cylinder of the spool holder had 5.6mm so I chose an inner diameter of 5mm. The middle section acts like a spring and is clamping on the cylinder.
I first made the wooden version of this hook. I thought this is a nice 3D project, too. It has 2 parts that are symmetrical. My model is for a 1,5" Pipe (inner diameter 39mm) and M6 screws. So you have to print 2 of them. The alternative…
Just a simple sphere with flat bottom and an matching rectangular recess for the mounting. The number of facets in the model is little bit low, so you can see it as decoration on the sphere.
The ring has a groof, where it is mounted inside off the watering can. The diameter is about 5% larger and there is a 5% gap of the circumference. This acts as a spring mechanism (if it does not work in the longtime, i will use glue ;-)).…
Minimalistic model created with OpenSCAD. Just the size of the flter itself. So the holder can act as a template when you like to cut larger (cheeper) 102 filters to 101 size.
Used a cutoff off a sphere as starting point for the template shape on the back of the box. Everything else is standard modelling.
These are all currently available results.
