28 models
A round spacer/standoff for M5 bolts, 10 mm long. Print settings: PETG. Before you print: measure your original part first and print a quick fit test. Not for parts carrying load, pressure, heat or electricity. Licence: CC BY-NC-ND 4.0,…
Not test-printed yet. Print the coupon first. I made this replacement turning knob for D-shafts, the round shafts with one flat side. It comes in four sizes, plus a small coupon to check your clearance before you print a full knob. All…
A fluted knob with a pointer for 6 mm or ¼" D-shafts. The shaft diameter, across-flat size, knob size and number of grip flutes are fixed in this free file. Print: ASA or PC near cooktops, PETG elsewhere. 0.12–0.16 mm layer, 4 walls, 30%…
A 100 x 40 x 3 mm card for a quick check of your printer's XY size and hole accuracy using any caliper: Outer steps: 10, 25 and 50 mm (outside jaws) Slots: 5, 10 and 20 mm wide (inside jaws) Holes: 3, 5, 8 and 10 mm (inside jaws) Overall…
My wife bought new shelves that turned out too short for the cabinet, so I designed these in Inventor and printed them. What's tested: the 20 mm wedge with the 6 mm-hole pin (Ø5.9 mm), resin-printed in ABS-like resin on an Anycubic Photon…
A stepped push-fit adapter with a 1° taper and grip ribs. Both diameters, the lengths, the wall thickness and the taper are fixed in this free file. Print: PETG or PLA, 0.2 mm layer, 3 walls, printed upright with a brim. Print a 10 mm…
For fans, heaters, amps and tools with plain 6 mm round shafts. This free file is a 30 mm knurled knob with a 6 mm bore and an M3 grub-screw hole. It pairs with our D-shaft knob. Print: PETG, or ASA near heat. 0.16 mm layer, 4 walls.…
A drilling template for 35 mm concealed cup hinges. The fence sets a 22.5 mm boring distance and the pilot holes are on a 45 mm pattern (compatible with Blum-style hinges). Use it as a guide with a Forstner bit and a depth stop. Print…
A curtain track runner for a 6 mm slot, with an eye for the hook. Print settings: PETG, printed head down. Before you print: measure your original part first and print a quick fit test. Not for parts carrying load, pressure, heat or…
A flanged rack roller that snaps onto the axle. The diameter (26 mm), width, axle bore and flange are fixed in this free file. Print: ASA, ABS, PP or PA only, not PLA. PETG softens at dishwasher temperatures. Use a 0.16 mm layer, 4 walls…
An L-shaped shelf peg with crush ribs for a snug fit and a lip that stops the shelf sliding off. Print: PETG, 0.16 mm layer, 100% infill, printed on its back plate. Print 8–16 per plate. Measure your original part first. Not for parts…
The fences straddle the board, so the holes always land on the centreline. The board thickness, dowel diameter, number of holes, spacing and clearance are fixed in this free file. Optionally, ream the holes or press in brass tubes so they…
Fit is untested and may crack in PLA. PETG recommended. If you print one, please post a photo and say whether it was tight or loose. Covers rusty, sharp rack tines, so there's no more scaling by 95/98/100% to find the fit. OEM tine cap…
A U-clip with a 5 mm peg for fridge and cabinet glass shelves, sized for 5 mm glass (compatible with many Samsung/Liebherr-style holders). OEM clips sell for $10–20 each. Print: PETG or ASA (PLA goes brittle in a fridge), 4 walls, printed…
A low-friction runner shoe for range drawers, furniture and fridge crispers, with countersunk screws. OEM glides cost about CAD$15. Print: PETG or nylon, printed flat, 100% infill. Measure your original part first. Not for parts carrying…
Fit is untested and may crack in PLA. PETG recommended. If you print one, please post a photo and say whether it was tight or loose. A tapered slip-on cap for 22 mm round legs that stops scratching. Print: TPU or PETG, opening up. Measure…
Fit is untested and may crack in PLA. PETG recommended. If you print one, please post a photo and say whether it was tight or loose. A finned push-in plug for square tube on chairs, racks and frames. This file fits 25 mm square tube with…
An edge-fenced drilling strip for 5 mm shelf pins on the 32 mm system, with a 37 mm setback from the edge. Put a pin in the last drilled hole to index the next run. Pairs with our shelf pin. Print settings: PETG, 5 walls. Bed size: this…
A desk cable grommet for a 60 mm hole: a sleeve plus a slotted cap (cap file included as model_cap.stl). Print settings: PLA or PETG, printed flange down. Before you print: measure your original part first and print a quick fit test. Not…
A slip-on end cap for 25 mm round tube and poles. Print settings: PETG or TPU. Before you print: measure your original part first and print a quick fit test. Not for parts carrying load, pressure, heat or electricity. Licence: CC BY-NC-ND…
A 12 mm domed bumper that silences cabinet doors. Print settings: TPU. Before you print: measure your original part first and print a quick fit test. Not for parts carrying load, pressure, heat or electricity. Licence: CC BY-NC-ND 4.0,…
A block with an 8 mm guide hole and a V-groove for drilling straight into flat stock or round bar. An optional brass tube liner extends its life. Print settings: PETG, 5 walls. Before you print: measure your original part first and print…
A drill depth stop collar for an 8 mm bit, held with a set screw. Print settings: PETG, 100% infill. Before you print: measure your original part first and print a quick fit test. Not for parts carrying load, pressure, heat or…
Fit is untested and may crack in PLA. PETG recommended. Not for button or coin-cell battery compartments. If you print one, please post a photo and say whether it was tight or loose. A replacement battery compartment cover, 45×25 mm, with…
A ball finial that end-caps a 20 mm curtain rod. Print settings: PETG or PLA. The underside of the ball is a 45° overhang and prints rough without supports: enable supports or slow the outer walls. Before you print: measure your original…
A bar drawer pull with 96 mm hole centres, for M4 heat-set inserts. Print settings: PETG, printed on its side. Print with supports under the handle: the handle bridge overhangs in every orientation. Before you print: measure your original…
A screw-on cable saddle for 6 mm low-voltage cable. Not for mains wiring. Print settings: PETG. Before you print: measure your original part first and print a quick fit test. Not for parts carrying load, pressure, heat or electricity.…
A snap-on test comb for finding your dishwasher rack's coated wire size before you print a clip, cap or hook for it. Eight openings from 3.0 to 4.4 mm in 0.2 mm steps, each size engraved beside it. Push each one onto the rack wire: the…
These are all currently available results.
