Counting matching models…
This is a Hot Wheels / Matchbox 1:64 scale model of a 4-post car lift for displaying different size diecast cars. This is a remix of EG3Dprinting's 1:24 scale for Hot Wheels 1:64 scale. These snap together so you don't have to worry about…
These wheel chocks will stop your Hot Wheels / Matchbox 1:64 cars from rolling around on unlevel surfaces. They work on the front wheels, back wheels or both. Very quick print! HW Chocks-ChockA is easier to print and comes off the build…
This is a Hot Wheels / Matchbox 1:43 scale model of a 4-post car lift for displaying different size diecast cars. These snap together so you don't have to worry about extra hardware or glue. I've added added a wheel chock near the front…
This is a complete set of Lincoln Log compatible parts. included are: 1 notch log 1 notch log base / half 2 notch log 2 notch log base / half 3 notch log 3 notch log base / half 4 notch log 4 notch log base / half Chimney Roof supports 3…
This easy turn table uses a 608 bearing and half of an upcycled Prusament spool (or any spool with a 51 mm inner diameter ). There is a shroud around the bearing that has a small airgap between the base. This is so that if you decide to…
Your largest of novels will be supported by a few turns of the handle. You can use either the “FancyScrew” or the “Screw” file. The FancyScrew is printed in such a way as to allow the handle to move freely within the leadscrew. I printed…
Cute dinosaur door stop for all your door stopping needs (maybe) Easy print: PLA or PETG .3 layer height or lower 15% infill No supports or brims Included the G-code to make it super easy to print
Small mitre box with a 1 inch / 26 millimeter channel for 45 and 90 degree cuts.
This building block is Plus Plus compatible but has a few differences. I'm excited to see what you can make with them!
Taking Triple G Workshop's hot idea a step further and making it super melty!
A very large nut and bolt to occupy your hands Printing: Bolt: ≥ 5 % infill Variable layer height Nut: snug supports on build plate (maybe not necessary but just to be safe for the first few layers, or live dangerously ≥ 50% infill to…
These wheel chocks will stop your Hot Wheels 1:43 cars from rolling around on unlevel surfaces. They work on the front wheels, back wheels or both. Very quick print! HW Chocks-ChockA_43 is easier to print and comes off the build plate…
Printing Tips: Material: PLA or PETG Layer height: ≤0.2 mm or 0.2 mm + variable layer height Infill: >15% Support: None. Orientation: Default, laid flat on the side. Adhesion aid: Not necessary unless you scale the model down. PrusaSlicer…
Dino ROAR! Dino eat tape! A dinosaur shaped tape dispenser for standard rolls of Scotch brand magic tape (¾ inch or 19mm). Printing; All parts were printed using a 0.4 nozzle. There isn't anything complicated here so I'm sure other…
Pocket hole jig for a 3/8th inch (~10 mm) drill bit. It is parametric so it can be scaled up or down to meet your needs. Kreg Pocket Hole Jigs seems to be everywhere. How about we save a few bucks and print our own? Why use a jig? It…
Originally created to adapt a DeWalt shop vacuum to fit the Carbide 3D Sweepy 2.0 Dust Boot but I find it fits adapters around the shop. Opening 1: 1 ¾ inches or 44.5 mm inside diameter Opening 2: 2 ½ inches or 63.5mm inside diameter
Simple spacer for stacking your RLC ( Hot Wheels Red Line Club ) Cars. No supports needed.
Webbing Adjuster for securing straps and a g-hook to connect to additional webbing. It is used as adjusters on backpacks straps, rucksack, luggage, harnesses, leashes, collars etc. Printing Suggestions: organic supports (it is slightly…
Got an empty filament spool? Got an ever expanding Benchy fleet awkwardly displayed? This spinning Benchy display will hold 22 models. *This design fits the standard 200mm (outside diameter) x 90mm (inside diameter) spools. It will work…
This benchy is hot. Really hot. So hot it is melting!
These wheel chocks will stop your 1:24 cars from rolling around on unlevel surfaces. They work on the front wheels, back wheels or both. Very quick print! The design does not requires a brim or supports. The .gcode is included to make it…
Carbide 3D Shapeoko 4 power supply mount. It may work for others but I haven't tried them. Fits 73mm wide x 36.5mm high power supplies. Easy print: Print on end vertically. No supports or brim needed crank the layer height up
Power up with these Pac-Man beads! The hole is 4mm so scale up or down as needed.
Display your Raspberry PI 5, Pi 4 or Raspberry Pi 3 with this simple, yet sturdy stand. This design allows for add-ons to your Raspberry Pi. I attached the Pi with 5mm nylon standoffs. No supports required.
Originally created to adapt a DeWalt shop vacuum to fit the Cen-Tec Systems bayonet but I find it fits adapters around the shop. Opening 1: 1 ¾ inches or 44.5 mm outside diameter Opening 2: 2 1/8 inches or 54 mm outside diameter
Channel your inner Bruce Wayne with this batman bead. Layer change @ 9.20
Easy mount for storing a pair of clamps. This was designed for Jorgensen parallel clamps but will fit anything requiring a 33mm opening. Printing: No supports or brim needed when printed as oriented in the .stl. This also aligns the…
Somedays, all you want is a hot shower with a cold beer. Parts: I used a 2 inch (50mm) suction cup with a 15/32 (12 mm) diameter hook / horn I had laying around. Any large suction cup will work with a hook, through hole or horn. Here is…
Webbing adjuster with a clip point for securing straps or to connect to additional objects. It is used as adjusters on backpacks straps, rucksack, luggage, harnesses, leashes, collars etc. Printing Suggestions: organic supports (it is…
Stand for Sillybutts Alchemist pump action blaster. Fits in Talon magazine loader.
110 Degree Vacuum Hose Holder/Hanger for 40 mm hoses. Printing: Print on the end not laying on its side. Supports, I used snug supports for speed. Infill, 15%,
Display your Adafruit PyPortal Titano with this simple, yet sturdy stand. I attached the Titano with 12mm nylon standoffs so I could use the reset on the back if needed. No supports required.
Happiest Baby SNOO Smart Sleeper cable holder to route the power cable on any leg of the bassinette. There are two versions, mix and match as needed: A short version that can be evenly spaced along the leg. A long version to hold the…
26mm or 1 1/32 inch hanger for towels. The frame top for the shower is one inch so I needed something that wasn't too loose or too tight. I use it for towels. You can use it for storing your cat or kid or whatever you want. Endless…
Woven Bowl Vase Works in vase mode, but I like to use 2 or more perimeters.
Simple tall case for the Cytron Smartdrive Duo MDDS30 Two Channel Dc Motor Driver. Supports a 40 X 40 X 20 fan with M3 30 mm standoffs. Printing: No top or bottom layers for airflow 5 perimeters Snug or Tree supports for the wire openings…
Remix of the awesome Proto-Pasta “cardboard spool side inner core insert for core rollers” In this remix I added a lip to help center the hub for a flush fit. This also stiffens the part to allow for reusability. Also, since I am not…
Easy Thread Bobbin for weaving, sewing, knitting or embroidery (floss bobbin). Two sizes; large for thicker thread, think friendship bracelets.
Quick assorted collar stays in various sizes. Includes 2 inch, 2.25 inch, 2.50 inch and 2.75 inch (51mm, 57mm, 64mm, 70mm). These can be printed before you figure out how to tie a tie!
Simple mount for my outdoor lighting solar panel. The mount taper off from 31mm to 26mm diameter to fit a variety or different applications. I originally made it for the Home Depot Hampton Bay 3 LED Spot Light kit to mount it on a fence…
Stand for Captain Slug's Caliburn 4 pump action blaster. The Caliburn4Stand fits in Talon magazine loader. The barrel can be supported under the Doom with either the Caliburn4U or the Caliburn4Rail attached to the Doom picatinny.
Simple sun shade for an outdoor device. Printing: No supports or brim needed Biggest layer height your rig can handle PETG or better since it will be outside.
Simple case for the Tobsun DC Converter Step Down Regulator 5V with M3 standoffs. Printing: No top or bottom layers for airflow 5 perimeters Snug or Tree supports for the wire opening Infill, I like honeycomb but use whatever you think…
Simple mount for my outdoor lighting solar panel. Fits a variety or different applications. I originally made it for the Home Depot Hampton Bay 3 LED Spot Light kit to mount it on a fence to get maximum solar exposure. Works with other…
This woven-look coaster is building on the earlier work of [andrei.erdei] while making some non-trivial changes to the original design. I've had good success with the following settings: 0.3mm layer height 3 perimeters 100% infill…
Help your insect friends find a vacancy in the hotel! Printing: Designed so the last layer supports a filament change for the sign. Variable layer height 5% infill No supports or brims. Scale up or down
Collet holder for Carbide Compact Router & Makita Routers; RT700C, RT0700CX3, RT0701C, RP0900K, 3621, 3621A Spots for either 4 or 8 collets.
Easy woven cylindrical vase. I like to print in vase mode with two perimeters.
Help your insect friends find a vacancy in the hotel! Open Insect Hotel Vacancy Sign to fill with your own material depending on what you want to attract. Printing: Designed so the last layer supports a filament change for the sign.…
Simple cactus to scratch that itch! Printing: No brims or supports 20% infill .04 nozzle or larger Optional color change @ 6.20
Simple wire hook with an open end so the wires can be easily added or removed. I made this to hang wires below a table on the 2X4 joists. Easily fits a #6 or #8 wood screw. Printing: Print on its side No brims or supports needed. Crank up…
Bushings for the Stinson L-5 Sentinel observer control stick mount. The auxiliary stick in the observer's compartment can be unclipped and removed. These stowage clips for the stick have a bushing to help secure them on the fuselage…
Easy pointer, spinner or hands with a 3mm hole for mounting. 60mm and 90mm in length.
Simple Beech T-34 Mentor spacer clamp to keep the canopy open in flight. Folds out of the way when not in use. I used this spiffy knob https://www.printables.com/model/318608-m6-knob BOM: 2 6mm nuts (or 4 if you want a lock nut as in the…
These wheel chocks will stop your Mini-Z cars from rolling around on unlevel surfaces. They work on the front wheels, back wheels or both. Very quick print! Fits wide and narrow wheel offsets. The design does not requires a brim or…
These are all currently available results.
