Counting matching models…
9MM Snap Cap / Dummy Round No Support needed 100% infill for strength Works with PLA (cycles for me) The rim is a weak point and can sometimes break off. I will be printing with PLA-CF and other materials, however these are very…
General Info 3x M4 (countersunk) holes on each hinge side No supports needed 20.50mm on each side of the hinge Models / Clearance 0.50MM_Print In Place Hinge.stl Default is 0.50mm gap (should work on just about any printer). 0.25MM_Print…
1-1/2 Inch Female NPT Pipe Thread to 1-1/2 Inch Male Barbed End 1 : 1.5 Inch FEMALE NPT Pipe Thread One model has a 6 sided hexagon for crescent / pipe wrenching End 2 : 1.5 Inch MALE Barbed (3 Inch) Additional model - TPU Washer – TPU…
Print in place nested rings (like a Gyroscope). No Supports. I've included the Fusion 360 file so you can modify the parameters if desired and change the model bodies. You can also hide rings and save the STL/Mesh without them to have…
40MM OD, 27MM ID TPU Washer (o-ring) for 1.5" Lay Flat Hose 2 Models with different thicknesses, 2.5mm / 3mm included Print with preferred TPU No support High infill (55%) Example:…
45 Colt / Long Colt Snap Cap / Dummy Round (No Supports) 2 Models 45LC Brass Dummy Model.stl - Brass Only 45LC Cartridge Dummy Model.stl - Brass+Bullet, Whole Cartridge No Support Needed. 5/3/23 : Added models with slightly undersized…
45ACP Snap Cap / Dummy Round 2 Models 45ACP Brass Model 45ACP Full Cartridge (With Bullet No Supports Print high infill, for cycling, the rim needs to be very strong, so use a strong material.
This is a basic PTFE plug or stopper that goes into the PC4-M6 or PC4-M10 pneumatic fitting. No supports, any 15% infill is fine.
Bolt for Gold Monster 1000 Modular system (Coil, Armwrest, Assembly Mount, Etc) Print threads up, with supports High infill for strength Recommend PETG, ASA or other type of UV resistant filament for longevity since this is an “outdoor…
Simple wall mount for an RPG-7. Use Two brackets to hold the rear (wooden) tube section and the front tube section just past the handle/trigger sections. Print 2 No Supports Use high infill. Test strength before mounting / hanging the…
Handgun / Pistol Shelf Hangers Coming Soon, Hanger Bracket 20mm shelf thickness 150MM Depth (From Edge) Rod goes into the barrel 1x 70MM length (for compact) 1x 130MM length (for full size) Print with high infill, and strong material (to…
Note: Print in ASA or other UV resistant material if this is going to be out in the sun for extended periods. No Supports needed 1 model per plate (Fits in Bambu X1C/P1P - anything with 256mm Cubed) Note: On Bambu X1C don't print the…
38 Special Snap Cap / Dummy Round No Supports Print with high infill
Wall (or other surface..) shelves for presenting slabbed (graded) comics, or comics in bag/board. No supports Prints either horizontally or vertically - Horizontally is faster/better 15% infill should be fine M4 countersunk holes
.410 Bore Shotshell Snap Cap / Dummy Rounds Notes Should be printed with proper material & infill for strength, especially for the rim. Models 410Bore_[2, 2.5, 3, 57_35mm]IN_Shell_Model_NoPrimerPocket.stl Has no primer pocket - Simplest…
1-1/2" to 1-1/14" [1.5IN to 1.25IN] Pipe Reducer/Coupler/Adapter (No Supports) No Supports required. Used to couple and reduce 1.5" to 1.25" pipes or tubes. 3 Inches of clamp space on each side of the adapter.
Cohiba Siglo IV Cigar Tube No Supports, Print with cap threads up.
14MM Airsoft Muzzle Device Timing System (Shims) These shims are printed and used to tighten muzzle devices (flash break, suppressor, tracer unit, etc) on 14MM Airsoft barrels to specific orientations. The shim(s) should fit between the…
Govee Hygrometer (H5075) Magnetic Mount (12x3mm Magnets) For mounting Bluetooth connected Hygrometer in printer, drybox, etc. H5075 keeps history so you can keep track of dry box humidity and temperatures over time. No support Press the…
10MM Snap Cap / Dummy Round No supports needed Print with appropriate material, and infill. It will need strength. Especially on the rim. PLA-CF/PETG-CF, For example Testing: Cycles in 10MM pistols
Deadpool themed Geocache token / coin. No supports needed 61.22mm diameter, but can be scaled down If you scale down too much with a large nozzle you will lose resolution on the text / image engraving.
Box with Lid for 4.25" x 2.50" Glassine Envelope Organization. The box/lid have a 4mm offsetting surface to lock them together. 0.4mm face offset for tolerance. There are also spacers included. 2mm and 4mm. The inside dimensions are LxWxH…
Minimal 8x8" Parts Tray. Some fillet on the inside edges to pull parts along the edge/wall upwards. Ribs on the bottom to more easily grab parts especially with flat surfaces No supports needed ~15% infill is fine
KJW M700 Barrel to M14 CCW Thread Adapter Fits (snugly) over the unthreaded KJ Works M700 Rifle and adds M14 CCW threads for threading on muzzle devices (E.g airsoft tracer). I made the sleeve that fits over the barrel long so it covers…
CGC Comic Slab Wall Slide Mount You need to print 2 wall mounts, and optionally 2 spacers, and the drill template. Slotted holes are 3mm spaced, so M4 wood screw (or similar size) will work. I recommend wall anchors unless lined up with a…
Replacement stock for Chiappa Little Badger TDX (Extreme Takedown) Uses an M4 (6mm depth is fine) heat set insert in the hole provided to attach to the stock shaft. M4x16MM (Or as close as possible) Machine Head screw to attach through…
Minimal 6x4" Parts Tray. Some fillet on the inside edges to pull parts along the edge/wall upwards. Stippling on the bottom to more easily grab parts especially with flat surfaces Prints in TPU well to make a squishy non-slip tray. No…
Basic PTFE/Bowden tube cap. Print in TPU for a better seal. No support needed
Minimalistic PC4 Couplers (M6/M10) w/ Mount/Holder No Supports Required Thread PC4-M6 or PC4-M10 pneumatic connectors on each end to create a PTFE / Bowden tube coupling point. PC4 Coupler Holder_Mount.stl is a mount/holder for 4x…
Inline PC4-M6 Filament Feed/Retract Coupler Inline PTFE/Bowden tube coupler, with space to push or pull filament through the PTFE tube. I use these inline with my dry boxes for retracting / loading filament. Cut sections of PTFE tube…
Bitaxe / Bitaxe Ultra Mount System BitAxe/Bitaxe Ultra Single Tray - For mounting a single Bitaxe / Bitaxe Ultra - can be mounted to the main tray or to any surface using M2.5 flat head bolts. BitAxe/Bitaxe Ultra Dual Tray - For mounting…
Mine Lab Gold Monster 1000 Wall Mount – This is for the shaft that the detector comes with. Other broom holders and similar things don't really work because of the distance needed from the wall because of the arm wrest , detector plate,…
Hex Driver Case (Organizer) w/ Lid (No Supports) Has space for 3MM, 2.5MM, 2MM, 1.5MM Hex Drivers Like these : https://www.amazon.com/HRB-Screwdriver-Multi-Axis-Quadcopter-Helicopter/dp/B07QGZW57K/ No supports needed.
Small 1911 Silhouette BB / Parts Tray. 160x100x7mm dimensions No supports needed.
Simple straight edge rails / fence that can be mounted to any threaded table. for CNC milling, to ensure squareness of a rectangular work piece. The work piece should still be secured with clamps or other adequate methods, but this is…
5x8 Reloading Tray 44 Magnum Sized No Supports
Minimal 6x6" Parts Tray. Some fillet on the inside edges to pull parts along the edge/wall upwards. Ribs on the bottom to more easily grab parts especially with flat surfaces The ribs can be printed with different colors easily, example…
MJX Hyper Go 1/14 Scale Turnbuckle Spacer These units always seem to come with the toe angle off and needing adjustment out of the box. Adding this spacer will allow you to tighten the turnbuckle down. You can manually chop off z height…
Boxes w/ lids for holding stamp dealer stock cards Fits stock cards that are 107mm wide and up to 70mm high. Examples: https://www.lighthouse.us/single-stamp-dealer-cards-blank-background.html 57.17MM Tall G&K 102BK Cards (These are…
Self Tap Machine Bolt Test Block (M2 through M6) Used in my projects to test my self tap formula for a given material, for self-tap ability in metric bolts (M2-M6). Formula used is METRIC_SIZE * 0.90 = Fusion 360 hole feature size Bolt…
Spanner wrench for tightening or loosening a Spitfire Tracer to a barrel. 19.2mm gap. No supports necessary. Print with good amount of infill for strength. Created with Fusion 360, so can be modified if needed, let me know.
Reversible Bookend w/ Customizable Space (100mmx50mm space) on either side. I created this with an insert so that the bookend could be customized more (printing with different materials, and customizing different inserts.) Customizable…
Dostoevsky - Crime & Punishment Sign/Placard , can be scaled up. Can be printed in multiple colors. No support needed. Example 2 color print project for Bambu X1C is included Script taken from Heritage Press 1938 title page.
Magnetic 100 Gram Silica Packet Container (For Dry Filament Box) I didn't have room at the bottom of my filament spool / dry box (SAMLA Based) for more silica packets, but there was plenty of space above the spools in the box. So I…
These are all currently available results.
![1-1/2" to 1-1/14" [1.5IN to 1.25IN] Pipe Reducer/Coupler/Adapter (No Supports)](https://media.printables.com/media/prints/467707/images/3833779_84360414-c412-4bb7-8416-d7704ab80c4f/f360.png)
