Counting matching models…
Now available in more sizes The original ghost (OG) is approximately 53 × 33 × 50 mm. It makes a fun little Halloween decoration for a desk, shelf, party, classroom, or wherever you need an absolutely terrifying presence. Print one or…
I made this from scratch to be compatible with the RostaP Multifunction Arm System. I wanted a stronger desk clamp and the ability to freely swivel the base without the teeth getting in the way. I also eliminated the need for one of the…
I designed this for a vacuum that was not made to stand up straight or lay down flat, yet remarkably didn't come with a stand or wall mount. The holder provides a good comfortable fit without very little wobble. The screw keyholes fit #8…
This bag carrier makes it easy to carry multiple items at once with a single-hook design that keeps the load centered, and an ergonomic natural-curve handle that fits comfortably in your hand. This is as strong as the walls you give it,…
This is a replacement insert block for the Laguna 14|12 and 14|bx bandsaws, with some design improvements to make it more effective, durable, and damage resistant than the OEM part. This doesn't need to be extremely strong, so don't waste…
Running PEX pipe in tight spaces and during remodeling jobs can be a challenge, especially when faced with obstacles, restricted spaces, and pesky insulation. Introducing The PEX Pusher , the tool you didn't know you needed that makes…
Designed to snap onto a standard 1 3/8" closet rod but can be used on smaller diameter rods as well. Print in something strong and flexible like PETG, with as many wall loops as you think you'll need (I recommend 4 or more).
Best printed in TPU, these feet will keep your cutting boards elevated and dry. The inside holes fit a #6 screw and a #6 washer with a 0.375" (3/8") outside diameter like the one linked below (Amazon Associate Links). A 0.375" OD washer…
This is a 45-degree offset feed neck to replace the clear plastic one that comes with the Spyder MR1 paintball gun. It's designed to use the old bolts and nuts, but if you don't have those, you can use 8-32 machine screws and nuts…
Say goodbye to the waste of single-use toilet paper and hello to the future! Weighing in at virtually nothing, this classy sheet of paper is the perfect companion for campers looking to shave off those extra grams and conserve precious…
This was originally made for a larger sized chemical resistant spray bottle, but I added the other sizes to fit a wider range of containers. The cups all measure 80mm tall so the screw holes line up. I printed the orange ones in PETG with…
This storage container is sized for a girl's makeup sponge. It includes ventilation holes on the bottom and top to allow the sponge to dry out between uses. The lid has to be printed with the top down, so find a first-layer pattern that…
There are plenty of other good models out there for this exact purpose, but this one addressed some things I had in mind. Key features: The body prints with two clean walls at .4 layer width. This seems to be plenty strong for this…
Designed for strength, appearance, and ease of printing, this travel set meets the needs of the whole family. I included three sizes for now but might add more later. The adult and child sizes are the same diameter and use the same top…
These are designed for cards that measure 60x90 mm, so check your dimensions before printing. The inside of the box is 62 mm wide, which gives a comfortable fit for the 60 mm cards. The walls are 2 mm thick with a 1 mm raised panel on…
This is an un-fancy box with nicely rounded edges, just the right size for storing kid-sized silverware in any available spot in the drawer.
I provided each letter individually as an .stl, and also the .3mf file with the entire alphabet fit onto a single plate AND a pause at the right location for inserting the magnets. Check with your printer and settings to make sure the…
The video explains it all. You'll need a 5/8" hex bolt and nut for this to work, preferably at least 6" full thread. Let me know if you have any suggestions for improving the design. I recommend printing with something strong with good…
During the rebuilding process following a catastrophic water heater failure, I relocated the ¾" plumbing pipes into the wall, where they should have been originally (the old pipes were routed through the closet floor). I built a plywood…
A compact, fully 3D-printable sanding block designed for quick and easy sandpaper changes. The model uses a separate base, ergonomic upper grip, and large printed thumb screw to securely clamp a strip of sandpaper in place. The wide,…
Bandsaw blades should be properly tensioned before turning on the saw for optimal performance, accurate cuts, and to ensure safety during operation. They should be de-tensioned after use to prevent the blade from stretching and weakening…
This replaces Sterling part number Replacement part number 1080397, Front Bushing, which allows the door to slide on the track without metal-on-metal friction. The OEM part comes with a piece of foam for the top of the bushing to prevent…
I installed a new Harbor Breeze fan and had a slight gap because of the original box placement. Also, the screws were exposed. This part addresses both issues. The ring joins together with a small press-fit dovetail connector, which is a…
My son wanted a towel bar that was closer to his height, and rather than trying to find a match to the existing metal one, I decided to design an attractive 3D-printable system that let me show off some nice pieces of wood from the…
This repairs and reinforces the car hitch for the CuteTiger brand magnetic tiles. It might fit other brands as well, so if you try it and it works, leave a comment with the brand. Print with something strong and impact-resistant. For the…
Measures 3.5" diameter and 1/8" thick. Print with all walls and no top or bottom layers.
This part repairs the top-front panel in a Bella 4 slice waffle maker, model # GH-819, which can break when you pull the locking mechanism. Part of the panel contacts tabs on the metal cooking surface, so print with something very…
One of the metal valve handles on my ten-year-old Oatey Quadtro washing machine outlet box broke around the center hub, so I modeled a replacement. The valve was not stuck, but the cast part crumbled anyway. I printed mine in PETG, and it…
Are you a crotchety old man who dislikes unexpected visitors, shenanigans, and inept drivers ruining your grass because they don't know how to back out of a driveway that they shouldn't have entered in the first place? If so, this sign…
The front display panel on this dishwasher is very thin, the normal act of pulling on the dishwasher handle can flex the display enough to break it. It will still function, unless the actual digital readout is broken, but the wide display…
This is kind of a unique piece for my raised bed, but someone might find it useful. One of the pieces goes inside a 4" corrugated pipe, and the second piece goes inside the first to provide the screen. For the water screen insert, print…
These flags are designed to help stop robotic lawn mowers from trying to climb over low trampoline legs. They create a taller, more obvious obstacle that is easier for the mower to detect before reaching the horizontal frame. They were…
This is the toy it's intended to fix: https://amzn.to/4iECK70 (Affiliate link) I included the Blender file in case you need to make any adjustments, but this was a perfect fit for mine.
Replacement cutting-disc screws are not available directly from Mammotion, and finding the exact M4 × 8 mm stainless steel screws with a pre-applied nylon locking patch is surprisingly difficult. A practical alternative is to buy standard…
These compact baby tooth keepsake boxes feature threaded lids, fine fluted grips, and a tooth design on top. Use the numbered lids to organize teeth individually, or choose the recessed tooth-outline lid for a simple single-color print.…
These are all currently available results.
