P
PrintablesTrekking
Ruger 10/22 Bench/Vise Block
This is a basic bench/vise block for the Ruger 10/22. It should work with any of the firearms that use the 10/22 rotary magazines. PLA/PETG. 4 walls, 20% infill.
- Downloads
- 279
- Likes
- 34
- Rating
- 4.5
All models
Counting matching models…
P
PrintablesTrekking
T-Post Hinge Support & Hinge
Update: April 2, 2024 Uploaded shorter hinge bracket for tighter fit between bracket ledges and hinge. Changed recommended infill to 10-20% cubic. Original Post: I needed hinges and hinge supports to hang ¾" pvc pipe gates that I had made…
- Downloads
- 159
- Likes
- 39
- Rating
- 5
P
PrintablesTrekking
Fork Gate Latch & Latch Clamps
Update July 16, 2025 Uploaded V4 Fork and V4 35mm diameter clamp for @SonaTop_2108106 who had a tight clearance situation. Original Post-July 21, 2023 This is a light duty fork latch for use with gates that are used for pass through or…
- Downloads
- 136
- Likes
- 30
- Rating
- 5
P
PrintablesTrekking
Camlock Inlet/Outlet for Cyclone Separator
These are female threaded inlet and outlet made for Dronnn's cyclone separator. https://www.thingiverse.com/thing:2829268 I chose to go with female threads since it offered more flexibility for the oddball collection of hoses that I have…
- Downloads
- 133
- Likes
- 16
- Rating
- 0
P
PrintablesTrekking
Estes Rocket-3 Fin Jig
A teacher friend at a local school asked me to help the 5th grade classes build and launch rockets. The jigs were made to assist with assembly and can also be used with rockets that have similar tube ID. The V2 Rocket Fin Jig was printed…
- Downloads
- 123
- Likes
- 14
- Rating
- 5
P
PrintablesTrekking
ZoomThrow Lever - Primary Arms 3-9x40mm Scope/Vortex Sonora
Edited April 2, 2024 This ring also fits the Vortex Sonora 4-12x44mm scope. Sonora is the Crossfire II 4-12x44mm branded for sale to dealers. Two of the stubs don't quite line up but close enough to work without alteration. Original Post:…
- Downloads
- 104
- Likes
- 8
- Rating
- 0
P
PrintablesTrekking
Dewalt 20V/60V Tool Contacts Cover
UPDATE: 17-Feb, 2024 @seanauff_1590030 pointed out that the 20V contact cover was a tight fit when used to protect the battery charger contacts. I have DCB112 and DCB115 battery chargers. These have an indexing tab that fits a notch in…
- Downloads
- 100
- Likes
- 12
- Rating
- 0
P
PrintablesTrekking
Dragonfish spout for 2x3 inch Gutter downspout
Working on house and had to remove the 1st floor gutters to replace porch banding and to work on porch columns. Extended 2nd floor gutter downspouts beyond 1st floor roof and the ends looked ratty. Remixed maxxkao's dragonfish to make…
- Downloads
- 44
- Likes
- 10
- Rating
- 0
P
PrintablesTrekking
50mm Camlock Male Threaded Inserts
The inserts here are designed for Bosch vacuum hoses with factory wands. I wanted to keep the wands attached to the hoses and still take advantage of Peter H's 50mm camlock system. You can make an insert for any wand up to 40mm OD. To…
- Downloads
- 37
- Likes
- 6
- Rating
- 5
P
PrintablesTrekking
Door Strike Locator
The door strike locator is used to mark the door jamb for the hole for the lock latch and strike plate. After several years of loyal service my locater walked off the job and I made this one to replace it. The locator is sized for the 1"…
- Downloads
- 33
- Likes
- 3
- Rating
- 0
P
PrintablesTrekking
Multitester VOM case for Tech TM-108 meter
Made a box to hold a Tech TM-108 VOM. Added two trays to hold the meter and test leads. Used 4-40x1-¼ inch screws. Added a third hinge and skipped the gasket. Box is PETG. Latches are from a PLA end roll.
- Downloads
- 22
- Likes
- 2
- Rating
- 0
P
PrintablesTrekking
VOM Multitester Case for Radio Shack 22-204 & 22-214 meters
Sliced and diced the bottom and lid in 3D Builder to fit the Radio Shack 22-204 & 22-214 meters. Removed FLUKE logo. Used 4-40x1-¼ inch screws, Cases are PETG and latches are PLA.
- Downloads
- 14
- Likes
- 0
- Rating
- 0
P
PrintablesTrekking
Crimping Die Box for short dies for Ideal Crimpmaster and similar crimpers
Remixed Maksym's box to have two short rows to hold the dies that I use with the Ideal Crimpmaster. Box will handle short dies from most manufacturers as well as most short clone dies. Used 4-40x 1-1/4 inch screws. Used PETG for the box…
- Downloads
- 10
- Likes
- 1
- Rating
- 0
P
PrintablesTrekking
Vise Jaws - Fiskars 9" Brush Axe
These are vise jaws to hold the handle of a Fiskars 9" brush axe while the blade is sharpened. I added 20mm x 10mm x 5mm magnets left over from another project. I have included file with no holes so that you may add magnets of your choice…
- Downloads
- 4
- Likes
- 0
- Rating
- 0
These are all currently available results.