Counting matching models…
This bigger version fits some slightly larger but common 7-piece dice sets. See my previous remix (based on 3DCentralVA's and the same size as that one) for other changes. Printing tips: Tray: The version of the tray marked "support-free"…
Remove the ears using a razor. I printed with the full brim (using Panchroma Charcoal Black), but without it only the corners had warped, so the ears should work. You can reduce them in Blender if you have a smaller print bed. For the…
Use paint-on supports. Paint them only on the underside of the keystone at the top of the archway (See photo with 3D printer showing the support). Use "enforcers only" support mode in PrusaSlicer so supports are only generated there. The…
Now you can sort the screws directly into practical bins! Use my d3 bins (d2 wave can be used for 40 & 35 mm slots) to keep them separated. I found that the upstream handle caused binding, so I recommend using the “contour grip” instead…
For assembly, use a mask and eye protection rated for the hazards and use products as they direct. See license for disclaimer. Originally printed in Hatchbox “Copper” PETG it looked like something brown and unwanted… Superglue worked fine…
I wanted a character to use for Pathfinder 2 Feiya's pet Daji, so I remixed G.Zeus' model to make it ready to use for tabletop (1/60 scale).
“Its basically a portable didgeridoo with finger holes to change the tone, so maybe its more like a DidgeriFlute. Anyway, is fun to play.” -chrisniederer The only photo available is my remix so I cropped out the new mouthpiece adapter.…
Remove any blobs after printing to improve fit and avoid denting the paper casing of an old slide. Remove any film negative holder from the Kodak RODFS50's caddy. Place this inside the caddy: Line up the tab with the indent on the left as…
This necromancer has a crown and a skull face/mask. The tips may not print fully unless you use a 0.2mm nozzle or resin 3D printer, but the print in the photo was made using an 0.4mm nozzle at 0.08 layer height with SUNLU Meta PLA…
Parts included: The cap is for the top (matches factory part). The foot is for the bottom (matches factory part). The adapter lets you use a 1-1/2" Schedule 40 PVC Pipe to replace a missing pipe (vertical support). Cut this kind of PVC…
The 6ft one may be considered "small" since it is low to the ground and since 5e considers a riding drake to be medium though 12' long. For the tiny version I recommend resin or 0.2 mm nozzle. I printed using FDM with a 0.4mm nozzle and…
100% infill for best balance and clarity (but if using opaque filament, a different pattern will be fine if balanced). When printing with 100% infill, I had to use .9 extrusion multiplier or print two at a time to equalize pressure…
Prints pretty well, even in PETG as shown in photo. I printed it on its side, slightly diagonally, to make the layer lines look like fur. If doing that, use paint-on supports to make base have enough supports to not detach from the build…
If you print the base separately (recommended) you can glue it on using super glue (cyanoacrylate) according to the glue's instructions, or using a 3D pen. For these sizes, I used https://i.imgur.com/HSpcnCO.jpg (posted at…
Place the screws through the "rear" holes (It is easier to install if you set them in the holes beforehand). Add (4) M3 heat-set threaded inserts into the "front" part. Look at the "rear" and place the "front" part on the front of the…
The Intel CPU fans designated as 80mm (due to fan diameter) are awkward and bulky, so I made this enclosure with mounting holes on both sides with an 82.5 mm offset to match the 92mm computer fan standard. You can use any standard 92mm…
I made these to fit into the Mechanical M3 Bolt/Screw sorting device (but my remixed tray is required for it to work without cutting).
Plugs for bowden tube (a plug the size of ID) and fitting itself (a plug the size of OD) Fittings from bowden tube with stopper to prevent tube from getting pulled in in the case of a tangle at the spool. Dual funnel: External funnel is…
Has a blacksmith hammer for use as a fighter or blacksmith enemy or NPC getting involved in combat. The hammer is modeled after old artifacts. Some traditional or new ones have a wedge on one side, but this is a symmetrical type which…
Mount the sensor board during the resonance test only. The bottom of the mount is level with the tip of the nozzle as per the VORON Legacy CAD file. Verify homing won't bump it with another VORON, but your safe z homing distance should…
The front shank hole matches the existing hole in the Everbilt “20in Shelf Support Bracket” that hooks into the double-slotted vertical rails (actually comes out 18.5" from the bracket when seated). The shank holes are designed for a #10…
Print at about 16% size for FDM for use as a shadow drake in Pathfinder 2 (or 8% for accurate 1/60 of 3ft long if you have a resin 3D printer; listed as 2 1/2 foot "space" here:…
These are all currently available results.
