Logoclic K40 Connector Outer and Inner Edge 135degree
With this connector you will be able to to connect to skirting boards at a degree of 135°. Now also with an inner corner model.
- Downloads
- 20
- Likes
- 1
- Rating
- 0
Counting matching models…
With this connector you will be able to to connect to skirting boards at a degree of 135°. Now also with an inner corner model.
Various Cynthia Parts Closed Bolt: Stops the bolt from rotating the entire way around, as well as adding a pic-rail extension for structural rigidity. Includes windows to see the springwell, and meshes with the left side of the blaster.…
I don't see the point of overhang test below 55degree as most printer should be able to do that. So directly testing 65 and 75 degree as a way to calibrate speeds and fan speed (or compare ducts variation, which I've been playing with on…
Hello i used 2 magnets and printed the 15mm pin and the wheel At the 15mm pin, glued on a 10x10x5mm magnet. And the other magnet is round 8x3mm, to go on the hole in the extruder. Printed this in PLA with green to yellow color change…
IMPORTANT: You need to add this to Line 20 of the G-code: M302 S85 This allows the Printer to do the Cold Pull. Be aware, that this is normally deactivated due to Security, since a Cold pull is pretty hard on the Printer, and should only…
A Stand for the Audient EVO 8 affectionately titled "the cradle", which holds the unit at a pleasing 45 degree angle
“The Cradle” I was sick and tired of my Audient Evo 4 shuffling around my desk… As someone who only has this interface for an overkill XLR mic utilized at my remote job, I haven't cared enough about aesthetics, until now. Given that the…
Replace the original MMU3 holder file mmu3-frame-holder-r4.stl Provided 0degree (horizontal), 10degree, 15degree , 25degree stl files. fusion360 source file provided, you can easily change the angle parameter to change it to the angle you…
13,1cm wide, 19,8cm long. Tilted 45 degrees If you would like to support me - you can buy me a coffee :) Also if you liked the model - share photo of your print <3 Check out my other models HERE Any feedback will be highly appreciated!…
XL5 Drone mounted at 25 degrees DJI Action 2 let me know what you think Category: R/C Vehicles
This is the first thing I have designed so it may be overly engineered but it works for me. I purchased the Creality 10W Laser module and as I have converted my printed to direct drive (using the Creality conversion kit) I could not use…
Same electrics needed as the Original Model. Hardware changed: Needed Screws: 2× M1.6 6mm screw instead of the 10mm For Lid and Bearing guide 6× M3 8mm countersunk screws For attaching the Motorhousing to the body 4× M3 10-12mm…
I did not want to cut the beams my roof should rest on at a 15degree angle and did not want to bend the metal angles (90 degrees) from the home depot. Solution: 15 degree (the minimum any roof should have for letting the rain run down)…
I find the speakers lean a bit too far back and direct the sound over my head (the speakers are roughly 3ft away from my head), so this is just to tilt it forward by 15 degrees to better align with my ears. Not sure if the newer versions…
Door Bell Mount
A 45 degree canted mount (right side) for use in conjunction with and optic or something Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: .2 Infill: 20 Filament: random pla black Category: 3D…
i just wanted something functional and mnimalist that would work w/ a few different things i was working on, and it did. i printed in petg and flexed a little to make it work, i dont think it would work in pla or pc Category: DIY
A pool has an outlet and an inlet. This part is for the inlet to redirect the water in a 45degree angle. To the bottom or to the center. The adapter has a diameter of around ~47mm. 2mm thread distance and a single starting thread. Source…
Customized version of https://www.thingiverse.com/thing:1904805 Created with Customizer! https://www.thingiverse.com/apps/customizer/run?thing\_id=1904805 Instructions Using the following options: intDiameter = 14 wallThick = 2 openAngle…
For the Ring Video Doorbell Wired 1st Generation – 2021 Release
A Stand for the Audient EVO 8 affectionately titled "the cradle", which holds the unit at a pleasing 45 degree angle
For the Ring Video Doorbell Wired 1st Generation – 2021 Release