Search results: azimuth

Sort order

Counting matching models…

P
PrintablesStuNZ

RC Tugboat with Functional Azimuth Thrusters

A fully 3D printed RC harbour tug with a working azimuth stern drive. The two pods rotate 360°, giving it the same rudderless maneuverability as a real ASD tug — spinning on the spot, crabbing sideways, and full thrust in any direction.…

Downloads
326
Likes
25
Rating
0

Celestron Alt-Azimuth Tripod Leg Clamp

This is a replacement leg clamp for the "Heavy Duty Alt-Azimuth" tripod by Celestron (Item #: 93607). It turns out “heavy duty” was a bit of an over statement. I got one of these tripods from an auction site as an Amazon return to use as…

Downloads
244
Likes
19
Rating
5
P
PrintablesPelf

Hadley Telescope Azimuth Bearing

This is an azimuth bearing for the Hadley telescope that uses a PTFE bowden tube as a low friction interface material. Bowden tubes are inexpensive and readily available, making them an ideal source of PTFE material for the bearing. The…

Downloads
222
Likes
43
Rating
5
P
Printablesnbrlt

Alt-azimuth base

Changelog V4, 01-06-25: Reinforced the Top part where the Altitude adjustment screw lives, to reduce bending during loading. Adjusted dimensions on the barrel nut housing in the hope of reducing movements (housing is now closed on one end…

Downloads
215
Likes
27
Rating
5

Rocker Frame Azimuth Control for Hadley Telescope (Metric)

This is an addon to Rocker Frame Project . It allows precise control of azimuth of the telescope. By default the control is manual using the turning wheel. Optionally you can attach stepper motor and some control to drive it…

Downloads
182
Likes
28
Rating
5
P
Printableslpaelke

Azimuth adjuster for iEXOS 100

(German below / Deutsch weiter unten) A problem with the iEXOS-100 mount by Explore Scientific is that one can’t really adjust the azimuth during polar alignment. However, there is already an M8 thread on the tripod, which was probably…

Downloads
156
Likes
5
Rating
0
P
PrintablesSDHayes

Azimuth/Altitude mount for the Hadley 114/900 telescope

CHANGELOG: 07.12.22 uploaded stl/3mf revised Dovetail Female parts, changed to include thumb screws to lock down the scope in the dovetails and stiffen up the overall assembly. Big improvement. Left the original versions up. I am using an…

Downloads
149
Likes
26
Rating
5
P

Azimuth Bearing for Hadley Telescope Hill Mount

I designed an azimuth bearing for the Hadley telescope Hill mount based on a design by Pelf. The bearing uses a PTFE tube to reduce friction and the assembly holds together when moving the telescope. Bolt holes have been lined up to match…

Downloads
134
Likes
13
Rating
0
P
PrintablesBrumbrew

Azimuth Adjuster for OneSky telescope

This is designed specifically for the Astronomers without Borders OneSky telescope . The ring gear is split into 3 pieces that fit very snugly, might require a touch of sanding. The snug fit and shaping around the upright means only one…

Downloads
113
Likes
20
Rating
0
P
Printablesc3n

Hadley sturdy mount azimuth bearing

I took the cross section of DontWorryAboutIt 's Hill mount bearing and modified it to fit Ivan Urbánek 's Strurdy mount for Hadley telescope . To build it you will need a bowden PTFE tube (4mm diameter, less than 1 meter long), 12 M4x10mm…

Downloads
112
Likes
29
Rating
5
P
Printablessnoot

EQ6-R Pro replacement altitude and azimuth knobs

I've been using these printed in PETG for the better part of a year without issue. Replacing the altitude lever-knob This is a drop in replacement. Start by removing the original lever and spring by unscrewing the internal screw. The…

Downloads
103
Likes
3
Rating
4
P
PrintablesPrime

AZIMUTH the World's First 3D Printed Compass

The AZIMUTH compass is made up of a 3D printed case and two dials engraved in transparent acrylic, the AZIMUTH compass, unlike other compasses, is equipped with a magnet and a compass rose as a needle. Its durable construction and…

Downloads
76
Likes
33
Rating
0
P
PrintablesSam Rosenthal

Hadley Telescope - Sturdy Mount Azimuth Bearing

An edit of c3n's azimuth bearing that is more in line with the visual language of the sturdy mount . The assembly process is very similar. However, to join the Upper Bearing pieces I used 3 heat set inserts in the female side in place of…

Downloads
70
Likes
17
Rating
5
P
PrintablesGlennOsiris

UN Logo No Wreath (Flat Earth, Azimuthal Projection)

The UN Logo without the wreath is basically the Azimuthal Projection (a.k.a. flat earth projection). Thought it would be a neat thing to print as a coaster. Meh.. But it's out here now in case you want to remix it. Like, to put it on top…

Downloads
64
Likes
11
Rating
0
P
PrintablesRedlow

Hadley Mount with Build-In Azimuth rotation

This telescope mount has an integrated Azimuth rotation. The design is a remix of my prior remix ( Z-Brace - a stiffer Hill Mount for the Hadley Telescope ). It adds Azimuth rotation with only a few extra parts. The new mount design has…

Downloads
61
Likes
9
Rating
0
P
Printables3DMason

Horizontal Azimuth "Spider" Sundial

The design auto-generates plots using a Python script based on the user's entered latitude. Other parameters of the sundial can also be modified; i.e. size of main dial, number of hours to display, start of January ring from center, ½ & ¼…

Downloads
60
Likes
20
Rating
5
P
PrintablesShekibobo

Skywatcher EQM35 Azimuth Adjustment Knob

This is an upgraded knob attachment for the Azimuth adjustment screws on the Sky-Watcher EQM-35 Pro telescope mount. This should allow more torque and finer adjustment for polar alignment. Remixed from:…

Downloads
48
Likes
6
Rating
0
P
Printablesteamonkey

Azimuth Bolt for EQ5 mount

The EQ5 azimuth bolt knobs are hard to turn and hurt my fingers in the cold. I bought a pack of M6x50mm carriage bolts with nuts but couldn't find a bolt knob model that exactly fitted my needs, so I made my own. This bolt knob supports a…

Downloads
33
Likes
4
Rating
0
P
PrintablesStargazerSteve

Vixen Porta Altazimuth Mount tripod tray

This is my ‘grab and go’ mount and the little tray has always annoyed me. It barely holds four 1.25" eyepieces. So I spent about 30 minutes in Blender (it's a pretty simple model) and 5.5 hours printing to get a much larger tray with…

Downloads
32
Likes
8
Rating
0
P
PrintablesJohei

Daveley Mount: AZIMUTH_AXLE_BOTTOM.STL with 6 holes Remix

I created a version of AZIMUTH_AXLE_BOTTOM.STL for the Daveley Mount with 6 instead of 3 holes (for M5 inserts), so that it is easier to use different adapters for mounting on tripods without having to unscrew the whole mount every time.…

Downloads
20
Likes
1
Rating
0
P
PrintablesAnish Mangal

Azimuth bearing

This is an Azimuth bearing for the hadley telescope, if one is using a flat wooden/hdf/mdf base. The cupped part goes on the underside of the telescope board, and the part with the three nubs goes on the base. One can experiment by adding…

Downloads
16
Likes
7
Rating
0
P
PrintablesBogumil

Meade LX200 Classic Azimuth Bracket

Equatorial wedge azimuth bracket Meade LX200 Classic 8inch

Downloads
16
Likes
1
Rating
0
P
PrintablesCompass3DP

Azimuth OD - Overdrive Guitar Pedal enclosure + DIY PCB Kit

Azimuth OD - The 3D Printable Overdrive Pedal Enclosure + DIY Electronics Kit This is the 3D-Printable enclosure for Azimuth OD , a DIY analogue overdrive pedal built for guitarists and makers alike. Get the PCB + electronic components…

Downloads
15
Likes
6
Rating
0
P
PrintablesazDave

Simple and Inexpensive Azimuth Indicator for Amateur Radio Antennas

The controller for my heavy duty antenna rotator stopped working properly, but the rotator itself has a DC motor and is easily controlled manually with just a DC supply and an inexpensive PWM controller for speed ramp up/down. To…

Downloads
15
Likes
4
Rating
0
P
PrintablesJosh Abbott

Azimuth Equatorial Wedge for Skywatcher AZ-GTI 54degrees

54 degree wedge designed to slip into the pilar of Skywatcher AZ-GTI tripod. Requires no additional hardware this way and makes very sturdy design. Lock thumbscrews into shaft, and use original 3/8 thumbscrew to mount AZ-GTI onto wedge/…

Downloads
12
Likes
2
Rating
0

Dobsonian Azimuth Sliders

Useful for an azimuth bearing/slider using minimal PTFE tube. The flat head screws compress the PFTE tube to lock it in place. The PTFE fit is pretty tight as is, I found one corner to be very tight, likely due to a z-seam. Print one to…

Downloads
11
Likes
2
Rating
0
P
Printables8-Ball-Studios

Celestron Alt-Azimuth Tripod Leg Clamp

I had a problem with the heat insert on the old design pulling out just because of how much force was being applied by the screw. So I modified it to be inserted without heat from the inside so it would always be held in tension by the…

Downloads
11
Likes
3
Rating
0
P
PrintablesIonascu George

Ratchet and clank a crack in time Azimuth PocketWatch

The hinge i have used is not printed. I have made a printable version .

Downloads
9
Likes
1
Rating
0
P
Printabless16n

Azimuth/VTA calibration gauge

Attach to the headshell and use it to adjust azimuth and VTA by ensuring no light is visible between the edges and an average height record. For azimuth focus on the front edge, and for VTA adjust so both edges are on the record surface…

Downloads
5
Likes
4
Rating
0
P
PrintablesKareem Hassan

Azimuth TH8S shifter knob: aim the grip, 24 positions, no tools

Every threaded knob stops wherever its thread tightens. A round knob does not care. An ergonomic one does, because the thumb dish ends up pointing anywhere. Azimuth splits the job: a core takes the official TH8S thread, and the grip sits…

Downloads
4
Likes
6
Rating
0
P
Printablesmanskirtbrew

Azimuth setting circle pointer for Dobsonian mounted telescopes like the Hadley

This pointer provides 20 degrees of adjustment in azimuth to make setting up your Dobsonian mount easy. It's built around a 12" diameter, 3/4" thick circle, but would easily fit larger or smaller diameters. Printing: I found the best way…

Downloads
2
Likes
0
Rating
0
P
PrintablesJay

Azimuth motor mount for dobsonian rocker box telescope to OnStep conversion

This bracket holds a StepperOnline 10:1 Planetary Gearbox Nema 17 Stepper Motor for Az Axis (17HS15-1584S-MG10) so that it can slide in one dimension (pulled by springs) to hold a drive wheel firmly against a Lazy Susan bearing. [It would…

Downloads
0
Likes
0
Rating
0
P
Printables

Hadley sturdy mount azimuth bearing

I took the cross section of DontWorryAboutIt 's Hill mount bearing and modified it to fit Ivan Urbánek 's Strurdy mount for Hadley telescope . To build it you will need a bowden PTFE tube (4mm diameter, less than 1 meter long), 12 M4x10mm…

P
Printables

Sunchronizer D2 - 400W module solartracker for elevation & azimuth axis by Nerdiy.de *New Version*

The “Sunchronizer D2" Dual Axis Tracker is a solar module holder. With it “standard” 400W solar modules can automatically track the sun on the elevation and azimuth axis. The Sunchronizer D2 is the successor of the Sunchronizer D1 . With…

P
Printables

RC Tugboat with Functional Azimuth Thrusters

A fully 3D printed RC harbour tug with a working azimuth stern drive. The two pods rotate 360°, giving it the same rudderless maneuverability as a real ASD tug — spinning on the spot, crabbing sideways, and full thrust in any direction.…

P
Printables

Ratchet and clank a crack in time Azimuth PocketWatch

The hinge i have used is not printed. I have made a printable version .

P
PrintablesNerdiy.de

Sunchronizer D2 - 400W module solartracker for elevation & azimuth axis by Nerdiy.de *New Version*

The “Sunchronizer D2" Dual Axis Tracker is a solar module holder. With it “standard” 400W solar modules can automatically track the sun on the elevation and azimuth axis. The Sunchronizer D2 is the successor of the Sunchronizer D1 . With…

Likes
27
Rating
0