1,723 models
Any feedback would be greatly appreciated . Nozzle: 0.4mm Layer: 0.16-0.2mm (Recommended) Supports needed (Paint-On Supports, Tree support) No Brim needed
Print approx. €22.38–€27.35 excl. taxPreliminary estimate for one variant
R2D2 Added to versions of g-code: Note the 33 hour label assumes you are printing both. %100 = 24 hours %65 = 9 hours.
Print approx. €7.78–€9.51 excl. taxPreliminary estimate for one variant
D20 Dice Box – Magnetic Hey maker! 👋 A practical and stylish D20 dice box with a secure magnetic lid. Features: Designed for 5×5 mm round magnets for a snug closure. Works with flatter magnets using a printed spacer. Secure transport and…
Print approx. €5.02–€6.14 excl. taxPreliminary estimate for one variant
Any feedback would be greatly appreciated . Could be use as a planter, pen holder, etc Nozzle: 0.4-0.8mm Layer: 0.24-0.4 (Recommended) Supports needed Scale it as you like :)
Print approx. €3.40–€4.15 excl. taxPreliminary estimate for one variant
With this die you will always score 20 :)
Print approx. €0.27–€0.33 excl. taxPreliminary estimate for one variant
I really liked the R2D2 designs that hold the Google Home Mini, the one that I liked the most was pbechard remix that has a tilt forward so we can see better the Google Home Mini. One thing that I noticed was that this model had some…
Print approx. €9.48–€11.58 excl. taxPreliminary estimate for one variant
Star Wars R2D2 Planter Vase. Can we resized to any size that you like. Could also be sized to use as Pencil or Pen Holder or Candy Dish or Bowl. There is a small hole in the center of the planter to allow for water to not fill it up. I…
Print approx. €22.08–€26.99 excl. taxPreliminary estimate for PETGSource material: PET
“These are not the tissues you are looking for” – Obi-Wan Kenobi (in 0 ABY to a Stormtrooper with allergies) Assembly The model is stored as a single multi-part STL file in “R2-D2 Tissue Box v8.stl”. Don’t touch it. Just don’t. If you…
Print approx. €0.05–€0.06 excl. taxPreliminary estimate for PETGSource material: PET
Any feedback would be greatly appreciated . Nozzle: 0.4-0.8mm Layer: 0.24-0.4 (Recommended) Supports needed Scale it as you like :)
Print approx. €2.32–€2.83 excl. taxPreliminary estimate for one variant
R2D2 Bas-Relief Portrait ' another version can be found in my club R2D2 Bas-Relief Version 2 by Peter Farell | Printables Store
Print approx. €16.20–€19.81 excl. taxPreliminary estimate for PETGSource material: PET
EN: This compact housing is designed for an LD2450 radar sensor with Bluetooth antenna and an ESP8266 Wemos D1 Mini V4. It is based on F-Square's multi sensor design , but is a new development except for the rear ball joint . The radar…
Print approx. €1.61–€1.97 excl. taxPreliminary estimate for PETGSource material: PET
Version 2 is now up. I found that supports were being difficult during print, so sliced into smaller flat pieces for alignment and printing ease.
Print approx. €3.58–€4.37 excl. taxPreliminary estimate for one variant
I designed a 20° and 30° honeycomb grid compatible with the Godox AD200 / V1 flash and the AK-R1 kit - that actually works. The included grid in the AK-R1 kit is a joke and does not work very well creating a small soft spot light. Be…
Print approx. €1.21–€1.48 excl. taxPreliminary estimate for one variant
Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm Filaments Used: PLA Control3d Black PLA Control3d White Swap Instructions: Start with Black At layer #18 (1.52mm) swap to White for the rest.
Print approx. €5.96–€7.28 excl. taxPreliminary estimate for one variant
R2D2 Finger Puppet. Opening of this model is around 18 mm. Scale to your finger using ruler option in Prusa Slicer. Note: R2 gcode is for .6 nozzle and includes organic supports.
Print approx. €0.84–€1.02 excl. taxPreliminary estimate for one variant
I designed this simple hex bases for my colleague's collection of several D20 dices of magic the gathering. They come with different heights which allows positioning them like a stairway. There is also a variant that turns the dice by…
Print approx. €0.21–€0.26 excl. taxPreliminary estimate for one variant
Předlohou mi byly obrázky a filmové repliky.
Print approx. €9.95–€12.16 excl. taxPreliminary estimate for one variant
R2D2 woggle neckerchief scarfing for Scouts and CubScouts. Pasapañuelo para lobatos y scouts
Print approx. €0.85–€1.04 excl. taxPreliminary estimate for one variant
Need a friend who can watch over your prints and give you a sense of unwarranted calmness? Someone to repair your spaceship after you've taken one too many laser blasts to the rear? R2D2 is your guy - and now he can dock with the Prusa…
Print approx. €0.10–€0.12 excl. taxPreliminary estimate for one variant
Festool suction hose reel holder - improve your tool management. Can be used in addition to : https://www.printables.com/fr/model/806346-festool-d27-suction-hose-holder…
Print approx. €2.46–€3.01 excl. taxPreliminary estimate for PETGSource material: PET
Printed on Prusa Mini with following settings PLA 0,6 mm nozzle 0,25 mm layer hight 40% Gyroid infill supports everywhere.
Print approx. €1.87–€2.29 excl. taxPreliminary estimate for one variant
R2-D2 LCD Knob replacement for stock 3D printer knobs suitable for all Star Wars fans!
Print approx. €1.40–€1.71 excl. taxPreliminary estimate for one variant
Držák baterie na podvozek Yokomo YD2 SXII, jednoduchý a funkční koncept. I po instalaci je stále možné použít odklápěcí držák baterie.
Print approx. €1.85–€2.27 excl. taxPreliminary estimate for one variant
When you start printing BigBricks figures you'll sooner or later get into trouble where to put them all, so I decided it was time for a proper wall mount. It works with the R2D2 BigBricks figure and is interchangeable with my regular…
Print approx. €2.60–€3.18 excl. taxPreliminary estimate for one variant
Držák čelovky Boruit
Print approx. €1.57–€1.92 excl. taxPreliminary estimate for one variant
Festool suction accessory holder - improve your tool management. Can be used in addition to : https://www.printables.com/fr/model/806346-festool-d27-suction-hose-holder Printing parameters Material: PETG (recommendation) Layer Height:…
Print approx. €1.32–€1.62 excl. taxPreliminary estimate for PETGSource material: PET
Replacement case for CAME TOPD2R remote
Print approx. €1.04–€1.27 excl. taxPreliminary estimate for one variant
dashboard pour fanatec dd1 dd2 https://www.amazon.fr/dp/B07PLF8V8Y?psc=1&ref=ppx_yo2ov_dt_b_product_details acheter l’écranIBest 5 inch HDMI LCD B 800x480 5 pouces et le le mettre dans les cache imprimé. les visses sont fourni avec…
Print approx. €1.13–€1.39 excl. taxPreliminary estimate for one variant
Accessory to catch dust. Tested with Bosch GWS13-50VSP 5 inch angle grinder.
Print approx. €2.59–€3.16 excl. taxPreliminary estimate for PETGSource material: PET
Overview Two part, threaded holder that uses 3x3 mm magnets to snap colour-correction gels onto Godox round heads. Sized for gels cut to Ø 70-71 mm. Compatibility Godox AD100 Pro Godox V1 (all mounts) AD200/AD200 Pro with H200R round head…
Print approx. €0.64–€0.78 excl. taxPreliminary estimate for one variant
Seperate Objects. For the Head generate supports only on the print bed. For both Legs generate supports on the entire model. For the main body generate supports only on the print bed. I recommend using 10% Gyroid Infill. I printed it with…
Print approx. €3.71–€4.53 excl. taxPreliminary estimate for one variant
Star Wars OnTop for Pen (TIE + R2D2) Attachment for the Ballpoint pen Gyroid + Cubic: https://www.prusaprinters.org/de/prints/126323-pen-gyroid-cubic-with-holder-kugelschreiber-gyroid Simply swap the screw and put the OnTop in the holder.…
Print approx. €0.13–€0.16 excl. taxPreliminary estimate for one variant
Motor Visualizer - R2D2 Stl-Files (without configuration) 3mf-Files (with configuration) for MK3S and Mini Printfiles (G-Code) for MK3S and Mini Print the desired visualizer and the holder and glue the holder on the back. Then glue the…
Print approx. €0.22–€0.27 excl. taxPreliminary estimate for one variant
Gif: https://imgur.com/a/cKzLrMf Parts Required: (2) 8x3mm magnets Glue (I prefer JB Weld Plastic Bonder) Instructions: Check magnet polarity! Apply glue in magnet hole. (Mine went flying because my extruder vibrated the press fit loose)…
Print approx. €1.59–€1.94 excl. taxPreliminary estimate for one variant
Cover per ld2410c e d1 mini.
Print approx. €0.94–€1.15 excl. taxPreliminary estimate for one variant
A fan mount for the Fujitsu D2607. It fits 40x40 mm fans of any depth. This design is only suitable for use in systems where the Fujitsu D2607 is mounted “normally”, like in common consumer cases, due to gravity holding it in place. I…
Print approx. €0.30–€0.37 excl. taxPreliminary estimate for one variant
This is a simple business card holder. It's 2.72" (82.55mm) high (X) 2.8" (73mm) wide (Y) and 2.7" (69mm) thick (Z) in full with a stand on the bottom and holder with tabbed ends on each side. I made it for some vertical business cards I…
Print approx. €4.94–€6.04 excl. taxPreliminary estimate for one variant
This is a simple D20 with a lid and in the main part it has a spot where you can store stuff, like dice, money, candy, and whatever else you can fit. It's 100mm at the largest point (while the top and bottom are connected) I added a tab…
Print approx. €5.31–€6.49 excl. taxPreliminary estimate for one variant
Audentes fortuna iuvat! Protect your Philips OneBlade with a travel case worthy of a Bohemian knight. Inspired by the iconic Saviour Schnapps and medieval scroll cases from Kingdom Come: Deliverance , this design combines rugged…
Print approx. €12.13–€14.83 excl. taxPreliminary estimate for one variant
I recreated the STL files in Fusion 360 and modified them for the Raspberry Pi Pico W. Additionally, the logo is now suitable for multi-material prints. With the type settings in PrusaSlicer, it can now be printed in any configuration.…
Print approx. €2.32–€2.83 excl. taxPreliminary estimate for one variant
A direct drive steering set with servo mount and steering arm made for Yokomo YD2S Printed on: Ender-3 pro No specific print settings needed My print settings: Layer height: 0.2 Infill: 100% !! NOTE !! U should print with something…
Print approx. €0.22–€0.27 excl. taxPreliminary estimate for one variant
EN: For my old BD250 impact drill from Black&Decker, I reduced the recess to a 22 mm radius using the great idea from 3D-Kalle . Material: HT-PLA / PLA Layers: 0.3mm Supports: recommended in the area of the recesses for the spirit levels.…
Print approx. €3.71–€4.53 excl. taxPreliminary estimate for one variant
An ESP32-C3 and LD2410C enclosure for your ESPhome presence sensor needs! No hardware is required, and all parts can be printed in any filament you want (except probably carbon-impregnated filament, since that'll mess with your radio…
Print approx. €0.20–€0.25 excl. taxPreliminary estimate for one variant
This adapter allows for using a 5 Generation iPad with a Bluetooth keyboard designed for an iPad 2. This adapter receives the iPad 5th Generation and mimics the shape of the edge of an iPad2 so that the iPad 2 can be placed in a Bluetooth…
Print approx. €0.16–€0.19 excl. taxPreliminary estimate for one variant
If you have this grill. you'll probably need this soon -- the included driptray is pretty brittle and bakelite-like. The height is overtall by a few millimetres. This is solely a cosmetic issue. I'll revise it if/when I need to print…
Print approx. €6.60–€8.07 excl. taxPreliminary estimate for PETGSource material: PET
Wir haben dieses kompakte Gehäuse entwickelt, um LCD2004-Displays einfach, sauber und platzsparend in eigene Elektronikprojekte integrieren zu können. Die Besonderheit liegt in der flachen Bauform und den flexiblen Montagemöglichkeiten:…
Print approx. €3.33–€4.06 excl. taxPreliminary estimate for PETGSource material: PET
D20 Dice Box – Magnetic (Magnets Imprinted) Hey maker! 👋 A D20 dice box with built-in magnet slots for a secure, stylish lid. Features: Pause your print to insert 5×4 mm round magnets directly. Secure lid hold for transport. UPDATE: 4 mm…
Print approx. €2.69–€3.29 excl. taxPreliminary estimate for one variant
This fidget d20 is squishy and satisfying, perfect for your desk or backpack! Note: This die has a tendency to not remain perfectly round, and as such isn't very good for actual TTRPG play. Better stick to your solid dice for that!…
Modeled a large d20 to print just for fun. Actually works quite well. I would avoid rolling it on any surface you don't want to damage (roll it on carpet). There are two models. One large, one not so large. The big one has been…
The R2D2 kit Card has a multicolor and a single color print and is print in place! The R2Q5 is a Multicolor only and is also print in place you should use supports for both!
Basic case for USB-C version of the ESP32 2432S028 2.8" module, also known as Cheap Yellow Display (CYD) / CYD2USB.
Festool D27/ D36 suction hose holder - simplify your tool management Where do you currently hang in your suction hose? Print your own Festool suction hose holder and make your everyday work easier and more productive. Do you need further…
This is the final version of ED209 in 1/10 scale. Includes all the parts to make this version as screen accurate as possible. Print at .1mm to avoid excess sanding.
I'll be honest, I didn't like some of the current cut and paste versions of the R2D2 Alexa Echo Dot 3 docks available, some of them had a lot of errors when slicing. I decided to make a "as close as possible" screen-accurate version from…
This is why I would never, ever allow a player bring a 3D-printed d20 to any of my games! It's just too easy to load the dice if you print 'em yourself. On the other hand, they would be OK for a player to use as a substitute for the…
This cat toy is unique and puzzling to comprehend at first glance, but prints all at once with no supports. The ball inside rattles around but cannot be removed from the D20 (trust me, I've torture tested it with my cats). It also makes a…
Just a simple Hose Clip for the D27 Festool hose. Category: DIY
This is my 1/6th scale ED-209 from the original Robocop movie. I've decided to give it away for FREE. NO reposting on other sites. Consider this a Printables exclusive - else or NO MORE FREE _SHIT for anyone. Also, NO RESELLING OF PRINTS…
Update 1: Small optimizations to the casing Added a small groove for lifting the lid Added some space inside on the back for potential cables Hello, here's a small project that I designed. I wanted to combine a small ESP32-C3 Super Mini…
Please comment, rate, and post a make! Update 2/1/2024: I've added a new back with a ball joint to give better flexibility with printing a single back for multiple mounting options. A simple case for using an LD2410C radar sensors with an…
KCD2 Wooden Chest for Philips OneBlade 360 Store your treasure! We present to you a wooden storage chest , designed specifically for the Philips OneBlade Kingdom Come II Limited Edition . The chest features a Wood-imitation body with…
Step up your tabletop gaming experience with the D20 Slot Machine Dice Tower! This unique 3D model combines the thrill of a classic slot machine with the functionality of a dice tower. With its eye-catching design and practicality, it's…
These glands can be printed in standing position. low layer thickness and good cooling is really helping a lot with resolution of the threads. But it is also designed to work with medium print quality. even bad stringing should be ok with…
I wanted to try Rangers of Shadow Deep one weekend so I needed d20 dice. I added a small chamfer to "Deliberately unfair (and fair) d20 dice" by Amatulic ( https://www.thingiverse.com/thing:4853423 ), so it rolls a bit better. Chamfering…
Slicer Settings Feel free to use whatever you're comfortable printing with, these are my recommended settings. Nozzle Size: 0.4 Layer Height: 0.2 (small&mid) 0.3 (large) Extrusion width: 0.3 (small) 0.35 (mid&large) Speed: no…
My version of R2D2 with moving legs, head, and retractable center leg. I may try to do more detail work on the skin in the future, but I'm not very good with that stuff yet. Inspired by someone's version with wheels and moving head, but I…
Description Keyboard stand, with an optimal ergonomic angle design, very comfortable for long-term use without wrist pain. Keyboard Stand with Upright Mode — Significantly Saves Desk Space Dual-Mode Keyboard Stand (Vertical & Horizontal)…
Finally, a D20 you can print with reasonable quality without support material! This model is fully parametric and can be generated/changed using OpenSCAD. Parameters that can be changed include: Diameter Corner/edge rounding Font Depth of…
UPDATE: Added varying severity of fillets (rounded edges/corners) for ease There are a lot of custom D20 models out there, but I didn't see any where it was blank and available for customizing… so… I watched a tutorial on how to and have…
UPDATE 2/10/2024: Be sure to check out the R2-D2 feet remix for use with the DUMMY 13 - Acrobatics pedestal I recently made a Lucky C-3PO by Printables user egz and decided there needed to be an R2-D2 to go along with it. If you like…
Bring the galaxy's most beloved astromech droid to life with this incredibly detailed 3D printable STL model that captures every iconic curve and panel line. This stunning figurine showcases R2-D2's classic cylindrical design with…
This is the stand you're looking for. If you like my work, please consider joining my patreon with Stand it Up Comics! https://www.patreon.com/Standitupcomics A little stand for the Alexa Dot 4, inspired by the astromech everyone loves.…
This is a redesign based on the idea and software from Ultimate ESPHome DIY Smart Sensor | fixtSE The individual sensors are clipped in neatly and are not loose in the housing. Printed with PLA, 15 % infill. Electronics used: ESP32 30 PIN…
Case to hold a LD2410 MMWAVE sensor module and a Wemos D1 mini board. The radar module can be rotated horizontally to adjust the angle and direction it is sensing. Four parts: The case that holds everything A holder for the radar module.…
https://www.youtube.com/watch?v=klmxXRzAuSU https://learn.adafruit.com/talking-d20-20-sided-gaming-die/overview The 20-sided die — or “d20” as it’s known to tabletop gamers — is an icon of geek culture. In this project we’ll 3D-print a…
A redesign of my original D20 Cookie Cutter that incorporates the stamp into one piece and a cutter into the other. There are two separate objects included in the file. They will print in place, so both objects can be centered on the…
Scaled for d20s that are approximately 20mm measured from face-to-face. I have oriented the d20 to be held with a vertex at the top, mimicking the original bulb's shape. After fiddling with my prototypes, I wasn't sure if I wanted to…
Adapter to connect FESTOOL™ CLEANTEC™ D27 Dust Extractor to DeWalt™ Air-Lock™ tools This adapter is designed to allow a FESTOOL dust collector with a D27 hose fitting to connect easily to DeWalt tools featuring the "AirLock" style dust…
Display your tabletop gaming dice with this Mage statue that nicely shows off your most prized D20. Includes 3 files Un-unioned 3D Unioned 3D Filled Dice area , This one does not have a place for a dice to sit and can be used as tabletop…
Cracked D&D dice set (D4, D6, D8, D10, D12, D20) fixed and optimized for printing
I really like the original design by Simomura, but found that I couldn't see the top lights of the Google Home Mini when interacting with it. My Home Mini sits by the TV and the angle of the R2D2 pointed the lights away from my viewing…
If you have D27 hose with taper then I recommend going with 3 of each size (Small/Medium/Large). For D36 you can just use the same size all the way along it. The wall bracket is for the D27 only. If you would like a wall bracket for the…
The SD2SP2 POR (Pro?) has a problem - there is a gap between the SD card slot and the GameCube chassis. It's very easy to insert the SD card into the void and you'll have to unscrew the GameBoy Player just to retrieve the card. Print this…
Please comment, rate, and post a make! Update 1/19/2024: I've added a new back with a ball joint to give better flexibility with printing a single back for multiple mounting options. A simple case for using an LD2410C radar sensors with…
I designed this as a Christmas gift for members of my D&D group. It can use up to 5, 6x3 round magnets to hold the cover in place. The hinges can be installed with a short section of filament. There's a top and bottom that have tabs if…
I made this adaptor to connect my Festool D27 hose to some cheap Titan shop vac attachments I bought, but it should fit any attachments with an internal diameter of 32 mm. The Festool cleantec end locks into place with retaining tabs…
Edit 09/04/2020: adding 0.10 mm depth in the magnet hole. A storage box with the shape of a d20 with correct number pattern. You can had magnets 7mm x 1mm to close the lid. Print instructions no support required at normal size you may…
Included dice are two-sided dice (d2) that have shapes similar to six-sided dice (d6) , but with joined parallel faces. For each die after rolling the result is what will be seen at the top of the die. Those are not standard dice used…
Drop in upgrade compatible with AR platforms and other AR grip type devices, including airsoft GBBRs. Features an ergonomic backstrap for greater control. Includes 4 texturing options for increased grip. Print bottom side down with tree…
* update * new harder version head available if you find this one to easy. https://www.printables.com/model/597903-star-wars-r2d2-lvl2-hard-edition-puzzle-with-windu Hey all couldn't find a a small r2-d2 that my rubbish printer could…
Demo video https://youtube.com/shorts/_D_-_w1XRVI I printed everything with a .2 layer height on a Prusa Mk3s, and have included the prusaslicer projects I used. I used support on build plate for the core although it may be largely…
This is a connector cover for a Bluetooth OBD-II scanner. No support material needed. Might require minor scaling (I printed it at 100% and it fits just right for me). Support If you'd like to support me for the 3D models I distribute for…
A basic D20 dice. Nothing super special. I did reference the proper design of a D20 dice, so the numbers are not randomly assigned. Printable with resin/ FDM. Standard tree supports with Cura work well. Print Settings Printer Brand:…
This is a multicolor only evil version of R2D2 R2Q5! Prints with supports on any multicolor printer colors are red, silver, and black! THIS IS THE SEQUAL TO R2D2 KIT CARD!
**UPDATE** - I posted a version 2 that works a bit better… https://www.printables.com/model/353451-d20-cookie-cutter-v2 My wife loves to bake and my son loves D&D and cookies, so I made a cookie cutter to look like a 20 sided die. It's a…
KCD2 Helmet Wall Mount for Philips OneBlade 360 Armor up 🪖 We present to you a helmet wall mount , designed specifically for the Philips OneBlade Kingdom Come: Deliverance II Limited Edition . The helmet features a functional holder that…
Descripción: Este soporte ha sido diseñado para montar un ESP32-C3 Mini junto con un sensor LD2450 de manera compacta y eficiente. El diseño incluye una base redonda ajustable con sistema giratorio que permite orientar el sensor con…
