Fluval Siena 330 feeding flap
feeding flap for Fluval siena 330 fish tank. No special mount needed. For assembly, use superglue
Print approx. €1.09–€1.33 excl. taxPreliminary estimate for PETGSource material: PET
- Downloads
- 7
- Likes
- 1
- Rating
- 0
140 models
feeding flap for Fluval siena 330 fish tank. No special mount needed. For assembly, use superglue
Print approx. €1.09–€1.33 excl. taxPreliminary estimate for PETGSource material: PET
Didn't fine any eligent solutions to this problem that retained the ball check valve used for priming the filter. So I made one. 1.5mm holes Print with ABS or PETG. I tested both. Settled on ABS as it looked nicer. Pictured is the PETG…
Aquarium spraybar for a Fluval 07 series canister filter. I used it with my 207 filter on a 29 gallon aquarium and it produces a low current flow and provides good aeration if placed above water. Laminar flow from the spraybar reduces…
After I bought a Fluval Flex 35l/9g (okay... just because it looked nice) I quickly noticed some flaws and / or opportunities to tinker :-) So I started to redesign and add some things. This is Part 2 (Part 1 is a fan mount for cooling…
This is a chamber 1 filter basket for the Fluval Evo 13.5 gallon Nano Reef Saltwater Aquarium. It's customizable, but there's an included model of the 3 divider model featured in the cover image and photo. The dividers for the…
This basket replace the stock filter in chamber 2 of the fluval evo 13.5 reef aquarium. With the new rooting, the filtration si more efficent. Edit : Revison 2 to include thiker wall for printing easier
A low-flow spray bar for the 15gallon Fluval Flex, designed to reduce the flow in 3 directions. Fits inside the outlet. Use PLA or PETG, no supports required.
This is a spray bar for the Fluval Flex 9 gallon aquarium, uses the existing loc-line flexible arms. Print flat end down, no supports. Greatly reduces water flow for shrimp and fry.
Here are my versions of the Fluval Flex inlet covers that give better coverage around the sides. These where made to fit the Fluval Flex 57L (15 gal) version, and I can't confirm if they fit the other sizes of aquariums. If you try them…
I have a Fluval 3.0 light. I wanted it risen to get better light. This is designed for a rimmed tank. I included the fusion 360 file because I assume someone can make it better. Printed in PLA. Took about 10 hours to print 2x. I have two…
This replaces the stock intake tube on a Fluval FX4/FX6 aquarium filter to add on a surface skimmer. I did about 10 iterations of the float portion to get it sized and floating correctly so it stays at surface. Been running in my planted…
I remixed the feeding hole cover by Robware to have ventilation holes in it. Had an Amano that wanted to go exploring one day… So I just wanted a cover that keeps them in, but at the same doesn't completely block the already limited…
I have shrimp in most of my tanks and have to filter the intake of my Fluval 107 and 207 canister filters to prevent shimp and fry getting sucked in the filter. I designed this because I was tired of dealing with a sponge other the stock…
This is a surface skimmer for the Fluval 07-series canister filters. This contains all the parts you need in order to print and mount your surface skimmer and enjoy that crystal clear and clean surface, free from scum and debris. T-Joint:…
Two simple arms/props to hold open the lid of the 57L (15gal) Fluval Flex aquarium. They are long enough so that they just fit diagonally on a Prusa MK3S printer bed (just a smidge over 29cm in total length). Update: Two shorter…
Fluval Compatible Light Riser – Rimless Aquarium Mount for Fluval Plant LED Lift your Fluval Plant LED light off the water and clear of the tank with this neat light riser, designed for rimless aquariums with 10 mm glass . It slides…
This aquarium was missing a cover for the feeding hole making it lose temperature and water over time. To solve this I created a cover with a drawer to feed the fish more easily.
3" Risers designed to fit into the factory brackets of the Fluval Plant 3.0 aquarium light.
This cover lets you pile gravel high above the bottom intake and fits snugly in 15-Gallon and 9-Gallon Fluval Flex
Replaces the stock output of the fluval FX for a more uniform, less direct flow. Perfect if you have fish that don't like too much current. Available in strait or 90 degree version. Only tested on my FX4, but should fit the other FX…
this is a model for the out nozzle on a fluval fx4 / fx6 filter.
Also doubles as a great way to suspend clippings in your tank :) 0.2mm layer height, 3 perimeters, no infill. ASA/ABS or PETG recommended.
I created this to protect my fry and shrimp from getting sucked up in the very large intake filter of the Fluval FX4 canister filter. It also helps with the sand. It will fit the Large Aquarium coop Pre-Filter sponge to the original…
Fluval Flex 9 Gallon Sliding Feeder Cover. PETG, 10% infill. Glue on the slide retainer
Tested with my FLUVAL AquaClear 50, but should work on most other AquaClear hang-on-back filters as I believe they all have the same intake tube diameter. Printing I printed it with a 0.1mm layer height (but used adaptive layers to cut…
Cover for chamber 2 and 3 There repace le stock cover There is the space for the lightprime 16 HD on chamber 2 and auto-top off system in chamber 3
The pump on my Spec V moves a lot of water, even on low setting. This outflow nozzle mod allows me to run the pump at full capacity (better filtration, more water cycling) without turning my tiny 5gal aquarium into a whirlpool. This part…
This is a spray bar i designed for my Fluval FX6 canister filter. I purchase my filter 2nd hand and it didn't come with the factory piece. i found most of the 3d printer options created too much current in my 110 gallon tank. This does a…
Modelled these Lid Props for my Fluval Flex 123l. For My configuration you need to print: -2x Fluval Flex 123l Front -2x Fluval Flex 123l Corner
Modelled these Lid Props for my Fluval Flex 57l. For My configuration you need to print: -1x Fluval Flex 57l Front -2x Fluval Flex 57l Corner
A short version of my spray bar ( https://www.thingiverse.com/thing:4661414 ) Made to be compatible with the Fluval 07 series canister filters. Prints in one piece. Supports on bed only. Print Settings Printer Brand: Prusa Printer: i3 MK3…
This media basket is a remix of https://www.thingiverse.com/thing:4388453. I loved the idea of the original design, but felt it needed some modifications: There is now small cutout on the trays to accommodate a temperature probe, such as…
Fx6 Locking Lid Handle I 3d Scanned , Works Great as a replacement. Could use It With the fx5 Filter Also. Post Up Some Pictures Completed. Please Do Not Resell Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No…
Simple shroud for Fluval Nano Plant LED light. Shroud sits on the lower edge of the light as shown in the IRL pictures. Aim is to control the sideways glare Category: Other
A nozzle / spray bar for the Fluval Flex 32.5 US Gal / 123 L Aquarium. It's quiet, maintains some surface agitation, and greatly reduces current in the water. Good for bettas or other fish that don't do well with strong currents. Plugs…
Frustrated with the lid during maintenance, I decided to make some props to hold them up while I worked in the tank. I haven't tried other tanks like the Flex or Spec range of tanks but do let me know. Printed diagonally on an Ender 3 v2,…
print with the inlet facing up, no supports needed, recommend PETG.
I've been looking for a 3D printed spray bar design for a Fluval Spec III (2.6 gallon) aqarium for some time, but with no luck. So, I went ahead and designed one instead! Tested on my aquarium successfully; it's not a super tight fit, but…
Fluval Flex 9 Gallon Feeder Cover. I used PETG, 5% infill, Plate supports. Can make with whatever parameters you want.
Replacement intake strainer to prevent filter from sucking up shrimp and small fish. Double height for more flow.
Replacement intake strainer for Fluval FX Series canister filters. Hole for mounting is 24.9 mm in diameter. Strainer holes are small at about 1.6 mm squares. No obvious reduction in flow with the Fluval FX4 over the stock intake strainer…
The pump in the Spec V is far too powerful for such a small tank. I'd seen several flow diffusers on thingiverse, but they were all for the old version of the tank. The new Spec V has a larger 13mm discharge fitting, and none of the other…
A simple light shade for the aquarium light: Fluval Marine Nano. This light shade slides over the top of your Fluval Marine Nano LED light fixture and keeps excess light from ruining the view. Especially helpful for tanks or lights that…
Made this for my 75 Gallon Aqueon tank, since all I was using before was some clamps and a block of wood.
This is a chamber 1 media filter basket for the Fluval Spec aquarium. It's customizable, but the models featured in the cover image are included. They definitely fit the 2.6 gallon version and probably fit the 5 gallon version too because…
This is for the Fluval Flex 32.5 gallon aquarium. This has two removable screens, that are held in place with the wedges on the side. I use Bio balls in the bottom, carbon in the middle and a filter mesh on the top. This is a snug fit,…
Lets you replace the original output pipe of the Fluval 107 or 207 to a small soft flow bar.
Floating plants (like Duckweed) getting caught in the filter outflow causes them to get flung into the water, where they usually get sucked up by the filter. This solves that by keeping them away from the waterfall. Additionally, it…
Split into 4 segments to fit on 256 x 256 build plates. Can rest in place but recommend gluing together with aquarium safe glue. Printed in PETG for water/heat protection. Has hole in back for aquarium equipment wires. Material: PETG…
A stand that is about 60mm tall and goes into chamber 1, it holds 10 BioSpheres made by Maxspect, specifically the Nano-Tech BioSpheres. The central shaft is for being able to pull it out when needed. I use this in conjunction with a…
Screw holder for Fluwal FX5 Akvarium Filter
The plastic lid that comes with the Fluval Spec 5 Aquarium is extremely lacking. It doesn't have anything keeping it in place and has a long, open slit down the length of it that your fish can either jump out of, or your cat get in to. I…
A quick mod added to model made by by Goldballz Designs . I added a bevel inside near the intake end to allow easier printing without supports. It will fit the Large Aquarium coop Pre-Filter sponge and the one from the amazon link below…
Die Halter sind für das Aquarium Fluval Flex 123 l. Da im Sommer die Temperatur um Aquarium eines Freundes gestiegen sind, wurden die Abstandshalter gedruckt. Es gibt drei Höhen: kurz - 10 mm mittel - 30 mm lang - 50 mm Es werden je Seite…
Just rounded the edges off for smooth surface and to avoid any fin damage
After I bought a Fluval Flex 35l/9g (okay... just because it looked nice) I quickly noticed some flaws and / or opportunities to tinker :-) So I started to redesign and add some things. This is Part 5 of the project. The whole project…
Spray bar specifically designed for the Fluval Spec III Aquarium. I do not have one but I hear that the Fluval Spec V has the same pump so this should also work with that as well. It is designed to snap onto any ball joint with an 11mm…
The factory lid for the Spec V 5 gallon fish tank is kind of crappy. It's awkward and a nuisance if you want to be able to mount a better aftermarket light, and it is a pain to simply feed your fish with this big slab of plastic in the…
This is a remix of the Fluval FX6 Intake Pipe created by Dezvinci. I had trouble with the coupler pieces he designed not fitting the pipes and intake strainer so I redesigned them. I also remade the coupler for the tube to hose joint so…
This is a basic filter cover for the Fluval Spec V all in one aquarium. The cover is designed to be printed simply and then placed on top of the filter utilizing the slot. This slot is just wide enough to accommodate for the filter wall,…
Filter optimised for 3D printing.
After upgrading my Spec 16 stock light to the Plant 3.0 as per Fluvals advice I was not happy with how it sits in the lid. This mount replaces the extending arms from both ends of the light and lets it sit securely in the opening. There…
This is an adapter that replaces the original intake of the fluval 107-207 (might fit 307-407?). It lets you use the aquarium coop Medium pre-filter sponge to filter more debris and prevent shrimp and fry from being sucked in.
Printed this for my Fluval Hang-On Breeding Box L. It separates the baby platy the mother gives birth to from the mother itself so that she doesnt eat them! It can be printed in one part if you have a bigger printer. I printed it in Part…
remixed for better flow distribution and capped end
Print two sets of the inside and outside pieces. I stuck them together using 6mm X 25mm bolts and 6mm nuts. See https://github.com/danhooper/3d-prints/tree/master for the python files I used to generate the files.
Light extension/lifter for Fluval Spec V. Lifts light up for easier access to aquarium without removing it. Prints on a standard Prusa Original style printer with pain on organic support at the apex of the arch for the bottom bracket.
Wanted to add a pre filter to my Fluval 106 canister filter in my planted tank (to keep soil out of the main filter). This allows for some filter foam to be cut and placed within the cage to act as a pre filter, which is easy to then…
A two part model which you glue together to form a slide in media box. This fits the Fluval Spec V 5 gallon tank. https://fluvalaquatics.com/us/shop/product/spec-aquarium-kit Make sure to use an aquarium safe filament such as food grade…
Made this so you can put larger baskets of activated charcoal and bio-beads with replaceable filter media up top.
The pot holder will clip onto the glass of the tank to hold a net pot for plants. There is an included file for making a decorative lip on the side of the glass. There are extensions to hold the default light higher These accessories will…
A simple replacement lid for the Fluval Spec V filter chamber
Update: I've made a new version that hangs down a tad more and has sidecovers. Thus not blinding you when standing to the side of the aquarium. A quickly made light reflector for the Fluval Flex 57L (15gal) aqarium lamp. It simply slots…
This lid is for a Fluval Spec V 5 gallon fish tank. The remix is inspired by the design from @Deividas and includes hexagonal openings for inserting plant clippings. I’ve printed in transparent PETG+ with 100% infil. The solid lid file…
This is a mount that holds a Grässlin Rondomatic 400 autofeeder, on top of a Fluval Flex 57L (15gal) aquarium lid. The autofeeder screws onto the mount (with the original thumb screw) and simply sits on top of the Fluval Flex lid. The…
This mount holds a Petbank CY-109 autofeeder on a Fluval Spec V without needing to remove the lid. The chute directs food into the space between the end of the stock light and lid. I find this feeder works well with nano foods, especially…
This model creates a diffuser for a stock Fluval Spec freshwater aquarium kit (has not been tried on the other variants). The intent is to create a way to slow down the current in the aquarium without significantly changing the water…
Bracket to hang Fluval Plant 3.0 light strips from suspension cables. Should work with any generic lighting suspension cable kit but measurements were done based on this kit: https://amzn.to/41ot35Z When choosing a filament to print with…
Tired of killing my fingers when cleaning my FX-6, so I made two different wrenches for the plastic knobs. Printed mine with PLA using 6 walls and 30% infill.
I lost the piece for the directional diffuser on the Fluval Multi-Chamber Holding Breeding Box, so I made a new one. This is the part that spits the water into the box. I made it with a snug fit. This is the breeder box -…
I needed a shorter intake for my fx4 considering the original is so long. This goes directly into the rubber connecter at the end of the hose. Should work on other FX series canister filters as well. I am using it in a 6.5 gallon tank in…
I have a Fluval EVO 13.5 which is acting as a reef tank, and found that I would like to put in an in line UV filter to help with any type of bad bacteria within the tank. In this search I found the Auqa Shield UV Sterilizer Desktop…
The small intake strainer was clogged frequently with debris, this part fits over to pre-filter. Our Fluval canister filter (406? I think) had an intake strainer with an OD of ~28mm. This strainer was designed with a tapered ID for a…
Needed a mount for my Fluval planted light that would fit a 20-gal long rimmed tank, and saw this one made by Nolibert. However, it wouldn't work for my tank or light since it's far too small, so I made some minor adjustments. Tank grip:…
I wanted to use the Fluval Nano Bluetooth 3.0 light with my Flex 9 gallon tank. So I created this lid to use with the light. The lid has openings in the back for my Co2, Air, and power lines, these are setup for the way I keep my tank.…
Fluval FX6 fx4 and fx2 socket 3/8 drive
Simply change the direction of the water flow as needed.
I lost the bulkhead for my flex and couldn't find one. Save yourself 10$ and just print this one. I used this nozzle with it. Enjoy. https://www.printables.com/model/819851-fluval-flex-15g-low-flow-spray-bar Supports aren't necessary,…
After finding a betta on the kitchen floor in the morning, we embarked on a mission to deter future jumpers. This is the 3rd iteration of the design. Does it work? Well, nobody has made it out of the tank so far. ;-)
Verschiedene Fluval Auslässe für die FX Filterreihe. Ich habe sie mit ASA CF gedruckt und diese immer entsprechend mit dem Adapter verklebt.
A simple cover to close the food opening. 10% infill; no supports; PTG recommend
I made this to fit in the throat of a Fluval surface skimmer. It keeps fish, shrimp, and snails from getting sucked into your filter. Print with no top/bottom, and adjust the infill shape and percentage to get the hole size you want. Keep…
I have a Fluval Plant 3.0 light mounted above my aquarium. It works great, but the light from the bare LED bulbs spills out in front of the aquarium and is quite blinding when you are too close at a low angle. I solved this by clipping a…
Floating plant guard Fluval Spec Fish Tank for suction cups. Spans width of tank to keep plants from filter intake and outlet. PETG 3 walls .2 mm no infill
The Problem with the Stock Fluval Flex AIO The stock 9-gallon Fluval Flex AIO design is poorly optimized for saltwater use, especially concerning the rear filtration section. The unorthodox twin-intake design results in the AIO water…
Fry & Shrimp Saver / Strainer – Fluval 107 Canister Filter Intake Stop losing fry, baby fish, small fish, and tiny shrimp to your Fluval 107 canister filter . This strainer adds a fine mesh screen over the intake to block small livestock…
After I bought a Fluval Flex 35l/9g (okay... just because it looked nice) I quickly noticed some flaws and / or opportunities to tinker :-) So I started to redesign and add some things. This is Part 1 of the project. Part 1.1 has a 80mm…
An attachment for the common Fluval HOB filters, that allows the filter's intake water to be skimmed off the surface via a comb arrangement that breaks up surface films. Rev1 revises the intake tube to allow the attachment to sit higher…
This is an approximately 9" riser I use on a Fluval Plant 3.0 aquarium light. It fits 6mm glass and is remixed from SpiceWeasel's model.
The parts are a tight fit: be patient. Honestly, I had to sand the male end a bit; perhaps uniformly scaling that part down a fraction of a percent would save post-process time. I recommend printing the spray bar with the closed end flat…