Small Mitre / Miter Box (1 inch / 26mm)
Small mitre box with a 1 inch / 26 millimeter channel for 45 and 90 degree cuts.
Print approx. €4.58–€5.59 excl. taxPreliminary estimate for one variant
- Downloads
- 384
- Likes
- 38
- Rating
- 5
151 models
Small mitre box with a 1 inch / 26 millimeter channel for 45 and 90 degree cuts.
Print approx. €4.58–€5.59 excl. taxPreliminary estimate for one variant
I am a model railroad enthusiast, which involves cutting a lot of plastic and wood profiles. These cuts often need to be made at precise angles. So I created this small miter box, adapted to the blades I use (0.6 mm thick). The miter box…
Print approx. €0.36–€0.44 excl. taxPreliminary estimate for one variant
I created this utility primarily for cutting ceiling molding at 45° angle. ⛏ Print instructions ⬢ Material: Prusament PLA Galaxy Silver ⬢ Layer: 0.2 mm ⬢ Infill: 40% Grid - bottom (base), 15% Grid - top
Large mitre box for sawing precise angles with a hand saw. Can be used to cut boards up to 6" wide. Available angles are 0°, 22.5° and 45°, as well as one vertical 45° angle. Outside dimensions of the box: 298mm long (11.73") 177.8mm wide…
Mitre box for 25mm (3/4") outer diameter PVC pipes Print Settings Printer Brand: Creality Printer: CR-10 Rafts: Doesn't Matter Supports: No Resolution: 0.3 Infill: 20 Category: Tools
Zero Clearance insert for the R225 mitre saw from evolution power tools. It has a dust box on the bottom with an opening at one end. This prevents dust from falling out the underneath of the saw and encourages dust to be flung up from the…
Small mitre box for cutting 45 degree angles. Gap for small saw blade is 1mm wide. Box internal dimensions measures 25mm wide by 30mm high.
Ryobi 900 Band Saw Mitre gauge. Never had one, so decided to make one. UPDATED 6/10/2017: Increased size of mitre base by 50%. Increased handle size by 50%. Corrected hole sizes for M3 bolts and nuts. I borrowed the angle marks from…
Miter / Mitre / Saw Box - 3 Sizes Same length of 240mm for all 3. Inside width of 22.5mm, 42,5mm and 64.5mm. If you fancy a different dimension, please let me know in the comments.
Layer height 0,2 Infill 15% Perimeters 2 Standard noozle 0,4mm Material PLA or PETG Supports NO
Mitre box to cut 2020 extrusion using hand hacksaw. Should be useful If you forgot to order a laser cutting service:) Guides should be done from steel cylinder with 6 mm diameter. Better hardened steel and it is possible to use metal…
Small redesign of ICant3DPrint exceptional Improved Mitre Cutting Box . The length is now suited to print on a 20x20cm bed like the Prusa Mk4's. This also decrease print time and filament usage. The model in the pictures is printed with a…
In rearranging my workshop I wanted to put the mitre saw as close to the wall as possible by adding a 90-degree elbow to the dust port for connecting a vacuum hose. I designed this in OpenSCAD and have a great fit with a tapered end that…
Saint Nicholas Mitre / Sinterklaas mijter 3D model voor sinterklaasfeest. The Saint Nicholas Mitre (mijter van Sinterklaas, Mitre de Saint-Nicolas, Mitra Świętego Mikołaja, Mitra Svatého Mikuláše, Szent Miklós püspöksüveg, Mitra di San…
Print and connect your Kärcher vacuum directly to your Bosch mitre saw. I cannot guarantee it will work for your Bosch mitre saw or Kärcher vacuum but my setup is a Bosch GCM 8 SJL and a Kärcher WD3 Premium. Just print and try, hopefully…
See it in action here The Makita 1019L/1219L Mitre Saw Dust Collection Adapter is designed to seamlessly connect your Mitre Saw to a 2-1/2" flex hose, enhancing dust extraction efficiency and keeping your workspace cleaner. This adapter…
Can be easily scaled for other evolution saws Concentrates suction and improves dust collection
I made a riser block for my mitre saw to prevent long objects like baseboards from falling down after the cut or tilting and ruining the cut surface. Normally these types of saws have extendable side tables but mine ( Bosch PCM 8 )…
The Design consists: a: Guidance with a tight fit. Please check the “TryOut.3mf”. In my case the fit gets tight with a left to right orientation (along the x-axis) and less tight along the y-axis. I needed to postprocess the printed…
Mitre box for making precise cuts at different angles, mainly 45 degrees. Suggested print settings: Infill: 20% Perimeters : 5 Top layers : 5 Please share your makes!
A simple model to connect my Bosch Professional GCM 8 SJL sliding mitre saw to a 35mm shop vac nozzle. Print both STLs @ 0.20 and 30% infil is enough. No supports needed, the overhang lip may droop a tiny bit but it didnt affect…
Multiboard holder for a Carpenter's / Mitre square (universal). This holder uses Multiconnect connectors. 2 of them is sufficient. Multiconnect is much stronger than Multipoint. The connectors are tool-less and very easy to move. The…
Lady Dimitrescu Fan Art Statue – Gothic Vampire Lady Diorama This is a highly detailed fan art statue inspired by Lady Dimitrescu, designed as an elegant gothic vampire lady display piece. The model features a tall countess-style…
42 mm internal diameter to 58 mm internal diameter vacuum attachment. Attach Dewalt DW715 Mitre Saw to 2.5" shop vacuum hose. Will work for other tools w/ 42 mm vacuum port.
Print the drop-in support block out PETG (or any other plastic that will not bond to the plastic used for the main model) and insert before the upper surface starts printing. It should key in to the hex cutout as shown below. Print main…
Little tool with great effect. It's not anodised in red but PLA or PETG works fine. Dimensions: 182x38x25.4 mm
I wanted to make a saw sled for my Ryobi RTS30. Since this is a contractor saw, it doesn't use a standard miter slot. I searched the webs and didn't find one for my saw. Using the original Miter Bar as a guide I made this. The saw is full…
One end connects to the Bosch "Click and Clean" port (45mm internal diameter) on your mitre saw (or other Bosch tool) and the other end connects to a regular 60mm internal diameter hose from your dust extractor/vacuum. Recommended to…
1. Introduction This simple adapter gives you the abbality to properly plug-in your Festool vacuum cleaner onto your Makita mitre saw. 2. Revision History Version Description Date A.1 Initial Release 15/01/2024 3. Printing Instructions…
Miter/mitre inserts - one style for flat head bolts and the other for standard hex bolts. 18.7mm x 76.2mm / .75in x 3in
Connects the vacuum port on a 10" Ryobi sliding mitre saw to the suction hose of a Dewalt shopvac hose for easy clean-up. Includes a 30° bend to keep the hose out of the way when using the saw. Print instructions Print standing up with at…
I designed this mitre box to cut the 32mm pipes required for another project - Filament Storage Solution (IKEA SAMLA) ( https://www.thingiverse.com/thing:743280 )
A mini mitre-box for working with smaller pieces. I will be changing the dimensions of the notches in the base very soon to emulate the mini mitre-box I saw at Michael's crafts store last night (each notch on the base is a different size…
June 8, 2026. I replaced v2 and 105 files with files labeled v3. The difference is that I added a strong chamfer to the leading lip or front edge. The problem with the earlier files was that the user had to carefully avoid contacting the…
print facing up with supports. I did PETg 50% infill with 4 wall layers for extra strength.
As others have confirmed, the Evolution Mitre Saws have rubbish dust collection. This builds on others ideas for the saw cover, now to find - or design - something that goes behind the fence… I found that normal supports work better for…
This is a remix from https://www.thingiverse.com/thing:4217831 I needed a stop block for my mitre saw that would attach to a length of 3x2 screwed to the fence of the saw for cutting many pieces of PVC piping. You just need to glue a 6mm…
Made some simple changes to make fit the 2020 V-Slot profiles
This stop block fits standard t-track with a 3/8 inch or 9mm gap, fitted flush to the workbench, rather than to a fence. For mitre saw stations where the fence is installed flush to the workbench rather than to a fence. The hole is…
Built for 1" (24.5mm) aluminum extrusions, but STEP files included for modifications. Hardware: M3 nuts [x4] M3 bolts 12mm [x4]
Check the dimensions of the T-slot before printing. You need 2x M6 Nuts 2x M6x20mm Screw
This is yet another mitre / miter box but with a unique difference! It is designed to hold and clamp 25mm x 11mm window fly screen frames to allow for easy accurate cutting of the required 45 degree angles. I designed it with two guided…
I printed this Miter Clamping Tool with Fuzzy Skin on the outside in Prusaslicer. This gives the clamping tool more friction on the surface of the wood. You could also glue a piece of sandpaper to the clamp to add more "sticktion". I…
A replacement blade guide pusher (german Führungsschieber) for an Ulmia Ott Mitre Saw, Type 352.
This lever (on off switch) broke and this is a replacement parts could fit others Metabo as well: KGS 216 KGS 216 M KGS 254 M KGSV 216 M KGS 305 M KGS 18 LTX 216 Printed in PLA with 6 walls, 6 top, 6 bottom layers in 0.4mm nozzle with…
Couldn't find a zero-clearance insert for the LS1019/LS1019L here so I made one. I've included the STEP files in case you want to make any changes to it yourself, up to you. I've modeled the rail supports as well, so it should hold up a…
Here is my Festool mitre gauge holder that I use to hold both my MFT and CMS router table mitre gauges. I screw the holder to my plywood tool wall using 4G screws. Print Settings Printer Brand: Prusa Printer: i3 MK3 **Rafts:** Doesn't…
Printed it in PETG with 80% infill, because the zero clearance slit you saw into it yourself. No supports needed.
Mitre bar with a tight fit for RIDGID R4512 table saw.
Any material will work, can be scaled up for wider wood profiles. Works best with "japanease" style pull saws.
This V block is a work in progress, I'm not sure yet where it's going, if anywhere! The idea was that it could be used as a conventional V block and sort of a mini mitre box too. There are straight saw slots in the V sections, but no…
I designed a Zero Clearance Mitre Saw Stop block. Using a digital reader, along with some aluminium bars and T-Track. Build video can be seen here:
My first model!! A new dust port to be able to connect a 50mm dust hose, at a 45 degree angel to the top port of the saw. This way the hose has a bit more freedom to move when the saw is turned.
Small little piece for perfect fit in the mitre slot of a Laguna Fusion F3 table saw. Might be useful to anyone who wants to print a feather board or such things. Designed to work with an M6 bolt.
Saw Guide for Wood Mitre Saw Blade The optimal method for boards thinner than 2 cm is shown in the photos (Appendices 1 and 2): Secure the board: Place the board in a vice. Attach the guide: Slide the saw guide over the saw blade.…
Simple guides to help with marking 55mm plaster cornice.
Original design leaves a lot to desire, so I designed a simple block which you can put on the support rail, slide it along and tighten with a thumbscrews in place. It will widen the range up to about 35cm. Obviously, you can use it on…
Simple mitre box for cutting 15mm trim/bead. Needed something to help make 45° cuts on some window beading.
Simple mitre box for cutting branches into cookies
My mom purchased a coil of 1.5" trim for her bathroom. Its a rubberised self adhesive trim that you can cut with scissors. I made a simple mitre box to cut it with a knife or hacksaw blade, to get clean cuts. I made the slots cut into the…
This is a version of my crosscut jig but slanted at 45 degress to make cutting mitre joints by hand easy. Just glue a piece of magnetic sheet to the cutting face and it will keep your saw on track as you cut.
The first model I made myself for my new printer, so be kind. Openscad files are included so you can adapt it for a different saw or fix any problems.
Keep your workshop clear from dust and debris by attaching a variety of different dust bags / extraction systems to your mitre saws. It fits to hoses with 34mm inner diameter.
My Ryobi mitre saw stand (the silver edition on sale a few years back, not the current green one) lost one of the rubber feet. So, I made one real quick. Category: Replacement Parts
Made this to connect the bag adapter on a Dewalt Mitre Saw. Pop the bag off the adapter, slide this on and connect a 2.25" hose. Done.
Replacement for Metabo Mitre Saw Guard Release Lever KGS 216 - all variants. Printed in PETG - use appropriate material. Use at own risk. Printed and tested for +months. No issues or wear.
Handle on my mitresaw broke off, so I cleaned the break and designed and printed a replacement for it. Then I just epoxied it to the existing screw from the old handle. Print instructions Category: Parts
All you need are two square nuts (m4 and m5). I printed with 0.2 mm on a Bambu X1 with PETG + Supports enabled. Print time approx 1h.
Printed with Galaxy Black PETG Nozzle Temp: 230c Bed Temp: 85c 1st Layer, 90c higher layers PrusaSlicer 0.20mm SPEED settings - 4 perimeters, 15% infill Position - Knurled End Down No Supports
Model tested with : a Karcher WD3S (Vacuum) Fits all Karcher WD3/KWD3 models equipped with the “Suction hose with connection piece” as shown in the last picture above and a Makita LS0816F (Mitre Saw) Might fit with : LS1110F, LS0815FL,…
A truly minimal fret slotting mitre (miter) box. It's designed for making additional slots in already fretted instruments: ideal if you're too much into Angine de Poitrine, KGLW, Massive Audio Nerve and other microtonal stuff and want to…
A 0 clearance insert should support the back of a cut preventing blowouts, thr original had a giant gap. I consider this part to be semi consumable and will replace it in time. Having fitted it I needed to trim the front a little and will…
Throat Plate Insert I made for the "AEG 10" Dual Bevel Slide Compound Miter Saw (Model PS254DB) The insert is split into two identical pieces to fit most print beds. Together, they form a perfect replacement for the stock throat plate,…
Makita LS Sliding Compound Mitre Saw ShopVac Vacuum Adapter 32mm ID /41mm OD ShopVac Vacuum Adapter to Makita LS Sliding Compound Mitre Saw Compatible Model: LS1219 LS1019 LS003GM102
Needed a guide to cut 16mm mini trunking So thought I'd add here. The one in the image is printed with a 0.6 nozzle, 0.4 layer height and in PETG.
I recently got a used Einhell TKS 15./250 UV tablesaw and the knobs for adjusting the mitre angle knobs plastic has broken so they didn't work as intended. It seems they used an M8 screw and flattened one side so I created one larger knob…
Makita mitre saw model LS0815 (and I'm pretty sure the other models too) is is fitted with a dust collection bag. This is a comprimised solution - the lack of positive suction and small capacity means you'll soon be covered in dust. The…
My mitre saw is up against my window, so I needed a good way to redirect the airflow and hook it up to my shopvac. Shopvac nozzle should easily friction fit for fast connect/disconnect. If not, add some painters tape. Using a DWS780, but…
A holder for Mitreapel CA Glue and CA Glue Activator Can. I also included the blender file so if you wanted to tweak the design you can as i was happy having the activator upside down with the cap on. otherwise my can does not fit. link…
Zero clearance inserts for Bosch PCM 8S sliding mitre saw. Inserts are intended to use only when saw is in vertical position, for other angles please use original inserts. For dimensions please see diagram, printer with table at least…
Edit 2026-05-04 - Version 1.1 Added additional 4x washers with different chamfers which let you increase the expansion to span a larger gap between the wall of the runner and the mitre slot. I modelled this based on the design from here:…
My Makita saw came with a plastic adapter to connect the included dust bag. I took them both off the saw to connect it to a dust collector and have since lost them both. It also turns out that when you buy a new bag, you also need to buy…
Zero clearance insert for the Mac Allister MMS210SL. I use the MitreWithSlot stl so I could then set the wall count to 5. When I then cut the slot using the saw it cut into the walls and didn't exposed any infill.
Here is a set of mitre boxes for cutting 19mm aluminum window screen frames. The grooves are sized to fit a standard hacksaw blade. The edges are radiused so you can hold it comfortably when making your cut. I originally needed to trim…
These are templates designed to slide over tubing (square and rectangular profiles) and use to mark out square and 45 degree mitre cuts, mostly for making simple welded frames and such. They are designed for metric steel tubing,…
Remix miter insert, for compatibility with zero clearance module. After print just click it in! No glue needed. As a bonus, when the zero-clearance insert wears out, it can be easily replaced. you can use my remix (screw holes removed)…
This is a dust extractor for a mini mitre/circular saw that I use to cut archery arrows to length (the saw is currently available under various brands on Amazon, eBay, etc.). My mini saw had an unused 4mm screw hole on the right hand side…
This sliding stop will make repetitive cuts a breeze. HOWEVER cutting any short timber on a sliding compound mitre saw requires care and comes with increased risks. Please ensure you are aware of the operational risks before attempting to…
Make your own lamp using a fallen branch! Lumitree is an adaptable lamp that clamps into your branch. You can make 2 models: 1 - LED Strip: Printed parts: 3x Branch Coupler(print-in-place) 1x Superior Base 1x Inferior Base 1x Joint A 1x…
Better dust extraction for the Makita DXT saw; these prints allow you to use two 32mmOD/28mmID hoses connected to a ShopVac. The elbow must be glued together (easier to print). The Hose to saw adapter is designed to be tight so you may…
Rear knob for Craftsman mitre saw. Modelled in Fusion360, Printed in PETG.
Adapted the Rigid 2.5" to a Dewalt Mitre Saw (DWS715) with a model created in onShape There are two versions, one that requires support (V5) and one that does not (V2) as long as it is printed vertically with the smaller opening on the…
Mitre Box 15.6mm Makerbeam XL. Scaled down remix so I could cut the beams. About 1mm of play using the settings of the original model. The channels for cutting do come up tight, I had to widen them as I cut so could probably do with…
Designed for 9mm thick fly screen, but if you're using thicker frame scal it up vertically in the slicer. You want it to be 15mm taller in the slicer than the depth of the fly screen. (eg, if your fly screen is 16mm thick, scale it up to…
Ersatzteil für eine Gehrungssäge deren Hersteller ich allerdings nicht kenne. Die Säge selbst ist aus dem Baumarkt. Das auf dem Photo oben liegende Originalteil diente als Vorlage für ein mit Blender erzeugtes Modell welches dann…
is a firm fit on the oval side to saw just sanded seem and pushed on.
Used to hold cylindrical objects with a clamp or vice. Designed to be used with Michael Hornung's Miter Box Can hold up to 3 rods between 6-12mm diameter. You can choose to use 1 - 4 jaws to hold your work. 6mm rods will be too small to…
Camlock Vacuum Adapter for AEG/Ridgid Circular Saw or Mitre Saw. Should fit tightly with some PTFE tape.
This is a simple mount to attach a 250V 12A softstart modul KR-009 or the 16A ZLB to a Scheppach mitre saw HM90SL without making any permanent changes to the saw. Just unscrew one screw that holds the bladecover, add the mount and…
This is a battery holder spare part for the Milwaukee M18 SMS216 Mitre Saw. Mine broke, which is why I designed a replacement. It's printed in 2 parts - Place them sideways on the print bed. I printed with PLA+ for now. Might reprint in…