122 models
This is a remix of the awesome looking OctoGlasses from Ramalama2 which fixes some issues in the original design. Design There are the following changes: The terminal cover on the left side of the board is now fully accessible The fans…
Wanted to add some options for 3D printing case feet for the NCase M2 to give a classic mounted GPU more airflow. They reuse the screws that come with the case, and can be printed in 10, 15, and 20mm heights. If you have SolidWorks, you…
Fan mount for the Ncase M2 (inverted layout) There are two different designs available: ITX (recommended): The fan cutout is not shifted. This allows an easier routing of the GPU power cables. MATX: The fan cutout is shifted towards the…
These are the clips that hold the side panels in on the NCASE M1 and Lian Li PC-Q33 (and maybe other) cases. I've tried in ABS and it works well, so far it's went through a lot of cycles of me taking the panels on and off. Not sure if PLA…
This was not my idea. Dimensions: 165mm long, 155mm between center of holes, 10mm wide, 5mm thick, 3.4mm holes(⌀). You could make it one or two mm thinner but I think that would work better with a stronger material like CNCed alluminum. I…
Original SMX Heinz design of the 3D printed slot 3.00 & 3.25 flipped travel kit. Designed to use with ABS filament. If you print with other filament you may have to adjust shrinkage compensation to get the correct dimensions. Installation…
Liteweight remixed version with zero gap between radiator and fan body, 25mm fans support in 3 slot mode, precise strong mount, support Corsair Venegance memory sticks and similar height even with shift brackets for AM5
Finally printed the BentoBox recirculating airfilter and made some changes to it and some nice cable management inside the P1S for 12V. I use the filter mainly when printing ABS/ASA to avoid VOCs and that nasty white deposit that…
This bracket holds two 120mm fans for the front of the case, it's about 10mm thick to avoid turbulence It pretty much maxes out the width of my mk3 printer and I also designed it to not require supports I added some slots for some magnets…
Those are brackets made for the Ncase M3 allowing you to mount front intake fans. They look good, they are well secured and make the grater pattern worth it!
This clever design is the work of OVERWERK + Scott Yu-Jan. All credits goes to them. I only adjusted the opening to fit an iPhone SE / 7 / 8 with a slim case . The wireless charger fits the Apple original or a cheaper alternative . Before…
Based on this plan . Make a new one, a bit longer and with a thicker gap to slide your MacBook Pro with his case protection on it. This is a MacBook Pro under the table rack. You use 2 screws per side to attach it under the desk so you…
Update 26/04/2026: - Added 15mm variant set. - The hole for these variant is 4mm deep. This require either a M3x3x5 or M3x4x5 as inserts - Replace the lower mounting hole as 2mm guide post instead. I wanted to try a different way to align…
Tested with 5080 founders edition YYMV. Uses 2 M3x4x5 mm threaded inserts .
The GPU mount uses the 4080/4090 Founders Edition M3 threaded holes hidden underneath the magnetic cover located at the front end of the card. The bracket attaches to the fan/radiator bracket of the Ncase M2 with M5 self-tapping screws…
A lightweight but sturdy 3D printable PC Case, fusion file included for modification, the X2 in a filename indicates that two of that part must be printed. This case includes space for one SATA SSD, and one standard sized Hard drive. It…
What is this? GPU Anti sag bracket to secure RTX 5080/5090 Founder Edition cooler from the rear side to eliminate sag. What have I modified from EIGA's original model ? Adjusted the model to fit RTX 5080/5090 FE. Made the structure more…
You will need M3 heat set inserts to mount them.
If you want to drive the bottom fans by the video card, you'll need an adapter. something like this will work although there are other options. I'm only linking this one because you can clearly see the pinout order, in case you have a way…
GenCase - Modular Open Air PC Case Short Description GenCase is a fully modular open air PC case designed for maximum flexibility and clean cable management. Unique feature: convertible orientation to route all cables at the case base for…
I readjusted this wonderful model from Eiga to fit my 5090 fe.
To protect my Rode wireless Go i made this case to print in TPU or TPE. Print Settings Rafts: No Supports: No Resolution: 0,2mm Infill: 15% Filament: any brand TPU or TPE Notes: No Support needed Category: Camera
Rear intake duct for the Noctua NH-D12L in an Ncase M2. Designed to work with a Asus ROG STRIX B650E-I GAMING WIFI Mini ITX in the 5th position. It may work with other boards, but probably not. Connect w/ fan screws and washers. Install…
Though NCase offers an STL file for 3D printing a 140/120mm fan mount for the M2 case, it didn't completely fit in my M3 (colliding with my PSU). I designed this alternative that allows mounting a 120mm case fan using the same technique…
Important: This is for M1 V6 only! Will not fit earlier versions! Printer: Original Prusa i3 MK3S+ Filament: Prusament PETG Slicer: PrusaSlicer 2.5.0 Slicer settings: 0.20mm Quality preset Other parts: Rubber strip (optional) Surface…
Dual 120mm front fan bracket for the Ncase M2 Grater featuring shifted fan holes for better airflow pathing around a side-mounted PSU. It should allow for more direct airflow to the CPU cooler for builds using the rear fan as exhaust.…
Building a custom VZBot printer and needed to cover this circuit board. This is screwed to a sheet of acrylic panel so thus the flares.
NCASE M1 sadly has been discontinued. Wanting to continue using the case, but making it more current with a usb-c port, I decided to remix RCodispoti's V5 blanking mod to instead have USB-A and USB-C ports. Uses the 2 original mounting…
I designed these feet in TinkerCad for the Ncase M2. The holes line up with the original holes for the little nubs, but I actually recommend placing them a little further inside. I mounted them using the screws and washers provided with…
ISO 4014 & ISO 4017 hexagon head screws with encased thumbscrew head. M3, M4 & M5 are available up to 50mm in length. Updates: 2025-09-06: Filament change note added for Prusa Slicer 2026-09-19: Revision 2 Update. Assembly thumbscrews…
Torus Knot with an Encased Ball and a Funnel Lilly Really just some random experiments with math, modifiers and use of wireframe in blender edit mode.
BTT Octopus Fancase that can be screwed from the top.
I printed them in PETG 2 of each and used the double sided gurilla tape for installation. Use 100% infill to give it strength.
The Ncase ITX Portable Monitor Mount Mod is a 3D printed accessory that allows users to attach a portable monitor to their ITX Ncase with ease. Using zip ties and existing case holes, it provides a secure and simple installation process.…
NCase M2 Side IO Uses standard M2 IO bracket and components. Secured with 2 m3 screws to plate and friction fit under case. Requires feet with 20mm in height to clear and fit snugly.
Adjusted the right side to mirror the left cutout in order to expose the 5v and GND rails on the Octopus. This allows you to run a DuPont connector where previously it was blocked by the original midpiece design.
I merged the 2 parts made by SKT to one solid piece that holds in place.
These are ducts I've designed for both Noctua NF-12 and Arctic P12 fans when deshrouding the PowerColor Red Dragon AMD Radeon 5700 XT in the NCASE M1 chassis to maximize fan-to-heatsink airflow and utilize 120mm fans to increase cooling…
This is a model based on bernabap's GameClip: https://www.thingiverse.com/thing:43977 It holds my encased Sony Xperia Z3 (74mm wide, 10mm thick) to the PS3 controller (Dualshock 3). I placed the phone over the controller for a better…
My strip connector from my incase bag broke. Designed (10 mins) and printed (30 minutes) in PETG. Heat the slabs a bit to make them easily bendable. Print instructions Print with 100% infill and in PETG.
Headphone holder that integrates directly into the front panel of the NCASE M2 Grater
120mm fan bracket for front fan mount on NCase M2 Grater. Designed to fit a slim fan when mounted under a Corsair SFF PSU at the highest setting using all 3 screws, and fit securely when the front panel side bar (not sure what that thing…
Inspired by a thingiverse design that also used 1" light duty ratchet straps whose design language did not call to me. Hexagons are the bestagons. Mount is intended to be used with #8 self tapping screws but M4 hardware should work as well.
FlexibleSkiDock with Encased Magnets: This is a remix of SkiDock such that the magnets are encased into the SkiDock during the print; added a frame such that a logo plate can be easily glued into place. Printed in TPU to obviate the need…
This elevates the dancase a4 sfx off up by 10 mm to allow for better airflow to a bottom mounted CPU cooler. This is alot better than the random knick knacks I was using before to elevate it. Prints in two separate parts, the notched part…
These are the 3d models to make an under desk mount for the NCASE M2. All parts besides the “Bump Pad” were printed in ASA, but other materials should also work. The “Bump Pad” was printed in TPU as it is softer. The screws used on the…
i didnt change the holesize of the original. this resulted in me drilling the bigger holes to 3mm. the build instructions can be found here:…
Requested remix for sidepanel adjustment to fit some higher cooler / pumpblocks in the SSUPD Meshilicious. NOT TESTED from my side. Category: Replacement Parts
The mount in the first photo isn't a perfect match. It had some small issues I fixed with the current version. Better tolarances, adjustability etc. Please comment and let me know if there are any issues with clearances or other things.
The NCASE M1 v6 has a USB-C port on its front panel, but if you've removed the front I/O because your GPU is too big (or you just don't like the look), then you lose one of your motherboard's USB-C ports. This model allows the USB-C port…
INTRO The stand NCase provide on their website was rubbish. So I made my own and this is it. The front stand can occupy two USB 3 ports, one USB-C port and larger power button. Please check you motherboard if you can add addtional USB…
You can support my works here: buymeacoffee.com This is a front dual 120mm fan bracket designed for the NCASE M3 Grater. The bracket allows two 120mm fans to be mounted behind the front grater panel for additional intake airflow. The fan…
Designed to fit on the bed of a Prusa Original printer mk2 and greater.
Bracket to mount standard 2.5" SSD on bottom grate of NCase M1 Evo or M2 (same pattern, not tested). Has holes for M3 threaded inserts. To print set, clone and mirror. Arrow marks direction to SATA and power. Printed in PETG for better…
Engineering work! Magic ball! Perfect for kids and cats
some simple spacers for the NCASEM2 case to increase the height of the rubber feet from 3mm to around 15mm for better airflow just need to have some extra m3 screws, I think they were 16mm in length
Uses standard Voron heats in the fan case versus in the actual fans.
To insert the pin, I squeezed the clip against the back of the holster with my fingers and used channel locks to press the pin through.
Bracket designed to use the USB IO Kit from Ncase and mount it to the front of an m3 grater. Uses 4 m3x4 heat set inserts and 6 screws. 2 - M3x8 for the feet 2 - M3x8 for the USB kit to the bracket 2 - Factory screws for the bracket to…
Replaces the original front panel of the NCASE M1 with a custom water reservoir. With this front panel reservoir, custom water loops inside the case should be made a lot easier. Also filling and draining is a lot easier with a reservoir…
30mm vented riser feet for the Ncase M2. Uses the original feet holes. Required hardware: M3 countersunk screw x4 M3 female screw (6mm flat round head) x4 (*connected length of both screws must cover around 27mm to fit properly)
You can support my works here: buymeacoffee.com This is a custom offset SFX PSU mount for the NCASE M2 Grater. It was originally designed around my Cooler Master V850 SFX PSU. I have also included a separate version for Corsair SF1000 PSU…
Replacement holster phone clip for encased holsters. Mine broke after 6 months and I didn't even know it, the phone stayed in place. I noticed when I went to take my phone out of the holster. So I modeled a replacement based off of what…
After running my previous feet on my M1, i decided to updated them now after 3 years as i am doing a build refresh. I've designed two versions of them as i was not sure which design looked the best. Decided to upload both of them so you…
I remixed @Meiji_Black_3253347's Rear Intake Duct for Ncase M2 & NH-D12L to make a rear intake duct for my NCASE M2 build with the Noctua NH-D12L on a TUF Gaming B850M-PLUS WiFi AMD AM5 B850 mATX Motherboard. Pictures show remixed duct in…
Designed for M2 DualC Front USB IO Kit (CNC Bracket Included) For the Grater just print exactly what’s contained within the STL. For other versions remove the IO foot and power button backplate then duplicate the standard foot. Use M3…
Posted on Thingiverse Oct 5, 2015. Any feedback is appreciated. If you print this, send me a message on how it printed. I am curious in how it comes out. Summary Wind Powered Electric Generator This model was created using Tinkercad.…
Included are the frame to mount the fans, a blend to direct the exhausted PSU air and a spacer to create some space behind the PSU to hide cables. Designed and tested in this set with the NCASE M1 V6
For detailed information - please check original model
This is a remix of 2ROBOTGUY's penny fidget spinner. The only change I made is that I added a 0.5mm top layer to each of the penny slots so that the pennies can be fully encased inside the spinner. Instructions: I sliced the spinner using…
This bracket is meant to help better secure a Corsair SF1000 to the back panel, in combination with the original mounting bracket. Keeps the PSU in place when only able to use 2 mounting screws. ***Not yet tested, may not work as…
This is a mount for a EK D5 pump in the Ncase M1, the best small form factor case ever, for use with custom water cooling. Features Reuses the internal SSD mounting holes Perfect fitment Secure & easy to remove Easy print Requirements 3x…
Box for iBMS and Smart Shunt connection. All components are in one box, easy to install on the wall using double-sided a
If like me you tore the storage sleeve trying to get it to fit I have designed a tougher replacement sleeve to be printed in TPU. Just add the bar plugs, tools and you're good to go.…
A design I made to support the Astral 5090 (or 5080) in the ncase m2 case. Small variations can still occur between cases and how it fits so check the fit yourself. This is for the normal (not inverted!) layout. Make sure to print it with…
Received Fanttik Solder Station for Christmas. Needed something to hold all the parts. Decided to design and print one. Case is 9" x 7" x 3" (230mm x 180mm x 80 mm) Printed using PRUSA MK3.5 using generic PLA filament. Will see how it…
The enclosure prints in place with build plate-only supports . I tested it with 0.2mm layers. Works in PLA and TPU for AMS (68D TPU). 0.2mm layer height Build plate-only Supports (tree) Check the bridge direction parameter so the…
This will let you mount your T1 pc case under the desk, saving space and improving cooling.
A decorative yet stylish holder for psu cables and aio tubes for your formd or ncase T1, not sure if this workss with other psus
Wall mount for baseball bat in a plastic cylindrical case that has around a 2.70" - 2.75" diameter
I have modified the original model to accommodate three 4010 fans. Additionally, certain areas have been thickened to improve structural rigidity. notes:1.Connect the main power cable to the motherboard first; however, note that this may…
This mounts to the side PSU mount holes and allows you to have a fan in it's place when you move the PSU to towards the front mount. Needs M3 threaded inserts: I used these (m3x5x4):…
Supports are needed. Use glue to attatch small parts on the body. All the 3D models of NemoMK2・Cults (cults3d.com) I'm selling more 3D printable things, take a look :)
You can support my works here: buymeacoffee.com These are custom 20 mm angled case feet for the NCASE M2 Grater. I designed them to increase bottom clearance for improved intake airflow, especially for builds using bottom-mounted GPU…
Plate that covers your power supply wiring and GPU wiring for the NCase M1. I've included the original Fusion file so you can modify it to fit your GPU if you'd like, or remove the GPU portion entirely. One thing to consider here is that…
Headphone stand designed for Ncase M1 Classic v6.1. Part has 4 threaded holes on the bottom that I use 4x 8 mm M2 nuts with washers to attach to top of the case. Two models are included: with and without cable management prongs.
I just wanted a floppy drive to write random files to it :3 https://www.amazon.com/dp/B0D4F8VGWM?ref=ppx_yo2ov_dt_b_fed_asin_title
skincase-czarny, fioletowy, żółty
You can support my works here: buymeacoffee.com This is a custom mount for installing an Aquacomputer Quadro fan controller inside the NCASE M2. I designed it as part of my NCASE M2 Grater air-cooled rebuild to keep the Quadro securely…
eep your Anycubic K3 printer organized and protected with this custom screen cover that includes a bed scraper holder. Designed for convenience, the holder ensures your scraper is always within easy reach, making it perfect for quick and…
Just a cover to block the hole if you don't want to use the headphone cable. To avoid supports I made it into two pieces that locate into one another. A dab of super glue should do the trick to keep them together. Category: Computer
This is a model based on bernabap's GameClip: https://www.thingiverse.com/thing:43977 It holds a Samsung Galaxy S6 with a thin TPU-case (72mm wide, 8mm thick) to the PS3 controller (Dualshock 3). I placed the phone over the controller for…
Mount for 92mm or 120mm fan at the front of the Ncase M2 grater case. Uses the attachments for the front IO of the standard front panel. Fit will depend on the components and layout you're using, but these were deigned to just clear a…
The clip will now hold the phone tight and it will not fall out. Increased griping strength. Well I guess I am a little OCD. The D ver of this really fits nice and snug, so I am now happy. Also if you have an MK4S with HP nozzle I…
I created this because my Encased holster clip mount actually broke off from a drop, so I made this to glue on the back to use temporarily until i got my replacement holsters that I ordered. Print with normal supports and a brim.
For this project you'll need some plexiglass around 355mm x 245mm (they usually sell them at 12"x16" online) I used 1/16" thick, around 1.5mm and some short m3 nuts and bolts, I think I used ones that were 6mm long To cut it up, I used a…
Bracket for 4 inch IPS display for N Case M2
U shaped feet for the stock foot locations on the NCase M2. These were inspired by https://www.printables.com/model/1246488-ncase-m2-feet but are my own clean sheet design that screws into the stock foot location but also allows you to…
I needed a version of this Skadis mount that is able to contain the WiFi Dev Board in its encased version since the original only allowed to somehow letting it sit loosely on top that's why I created this model using Eddieprints Original…
