Voron 0 Filament latch Remix for no drop nuts & Siboor Kit (1515 Extrusion)
Short legs version for Siboor/Makerbeam extrusions, and the stumps version won't interfere with no drop nuts.
- Downloads
- 223
- Likes
- 32
- Rating
- 5
59 models
Short legs version for Siboor/Makerbeam extrusions, and the stumps version won't interfere with no drop nuts.
As the extrusions for the Siboor Voron 0.2 R1 are different that the LDO extrusions, I couldn't find a model that fitted. Hope this helps other people. You might have to play with the tolerances as it is a tight fit. Cleanup up the…
Use the F623ZZ bearings from the original siboor cable chain swivel, an m3 heat set and a M3x16 BHCS. Placing the heatset can be a bit tricky, be careful not to damage the swivel. Print orientation as in the .stl, Voron standard settings.…
I have downloaded this file, and it did not fit the Siboor led lights I had purchased, Since I printed them on ABS, as it shrinks by around .5% on this long piece it was 2mm too short, so it was remixed with those tolances in mind, and…
Simple nozzle brush that mounts to the bed frame. Needed a way to wipe before cartographer does it z offset using touch. Brush used : https://s.click.aliexpress.com/e/_mMPr8W8 Print in ABS or ASA Need 3m x 16mm long bolt and your choice…
Compatible with SIBOOR's Voron Trident kit and Clicky-Clack Fridge Door.
Stealthskirts for the Siboor awd trident 300 with extended front skirts for the fridge door, hdmi5 v1.2, inverted electronics bay and filtered power inlet.
Fumepack mod for the siboor trident with mounting for a cpap blower/driver and mounting for the biqu turbo fan kit.
made the legs thicker and stronger, added optional way to screw in 2 m4x40 screws in the center legs to increase strength even more! ( not needed though ) rounded of some of the corners to be in line with the other curves scaled object up…
Fan splitter PCB mounts or PCB isolators for recent Siboor Trident builds. I didn't feel comfortable just mounting the PCB's directly to the 2020 extrusions with exposed pins at the bottom so I made these. Use M3x8 SHCS and M3 T-nuts…
I got the same led bar from Siboor as the creator but I wanted an even stronger diffusion, total height is 4 mm, adding a photo with clearence on my printer, mileage may vary. If the diffuser doesn't sit flush on the pcb you need to snip…
The original fan ducts conflict with the vertically aligned neopixel LEDs. This fan duct has a slightly lower profile and does not conflict with the neopixel LEDs. The airflow was also designed to be as equal as possible …. I think. This…
4x M3 heat set nut 6x M3x8 SHCS 2x M3 T-nuts The siboor kit includes a fixed mount. I felt that the touchscreen would be easier to use with a mount can tilt.
Test cube inspired by VORON CUBE V7. #1 Added 0-90degrees overhang test #2 2x vertical heatset, 1x horizontal heatset (VORON spec M3 heatset insert) #3 M20x0.2P #4 Overhang similar to VORON CUBE #5 45/55degrees overhang test #6 Siboor…
Latest revision but still untested
This will help you to organize cable!
I have noticed my extrusions are not consistent, if you find they are too lose when you print, (test before you place the insert, in case you need to reprint) You may need to scale the part up 1% Have you ever gotten done with a build,…
Side lift handle for Voron v0.1 Youth Edition kit by Siboor. Fits custom cut acrylic side panels and won't fit other side handle models. Based on Voron design team's door handle profile and scaled to fit. Install with M3x14mm screws.…
Logo design rights goes to siboor. ABS is suitable! Use it as your multi color print test :) I recommend to use Black&Cyan combo! Siboor Discord https://discord.gg/UxvMpJbaYM I highly recommend Siboor VORON kit!…
SIBOOR LOGO for Vorons Skirt Based on RJ45 Jack from Tomas (really nice model!), I created a nice Siboor logo shield for my Voron Trident 350mm from Siboor. It can be attached nicely in skirt-hexagons. Print / Install Instructions: place…
Print using Voron standard settings. Screw 2x m3x6 bhcs into the bottom plate, let them stick out about 3mm. Put the keyhole over the screws and slide it into place, then screw it down tight onto the plate. Make sure the opening of the…
Siboor modded fumepack now with a hole on the left or right.
Made for SIBOOR CNC plate
This mod allows you to install the archetype on the cnc carriage siboor
This little peg can be used to mount the siboor led bar/pcb on a voron v0 frame. Insert two M3 nuts in top extrusion, use M3x8mm to fasten the mounting peg to the extrusion, use M3x6mm to fasten the PCB to the mounting peg. Bar is mounted…
Please check the → GitHub page ← for more information about this design before printing. If you appreciate my designs and would like to support my work, you can do so by buying me a coffee. Your support means a lot!…
Push the part to the back and slide it down to secure it. After securing it, put the printer on its side, insert the M3 nut inside the 1515 extrusion, and slide it to line up with the hole. Use M3x8 screws to secure the cover plate.…
Planetary gear extruder have some COM problem, so i tried to fix the problems by lowering the motor and supporting it, so i have much less vibration and more accurate readings from the accelerometer. perhaps also compatible with other…
BOM: m3 8x12 (carriage, extruder, hotend fan) 2x8 (fans) M2.5 4x8 (radiator) 6 m3 heating insert
This mount shifts the Fly Gemini mainboard that is included in the Siboor kits and gives necessary 9mm extra space for the USB connectors. Simply print them (recommended ASA/ABS) and replace the nylon spacers. For mounting you will need…
The beefier legs remix didn't completely eliminate wobbling and knocking against the side panel, so I attached it to the Y gantry using a plate that goes through the very small clearance between the Y gantry and the side panel. Print…
This mod will mount the DIN rail on the Siboor Trident bottom panel
Edited the connector tabs to be 2.8mm thick to fit better on the Siboor extrusions. I found that the original and the remix for LDO extrusions did not fit with my Siboor kit. Just quickly resized the connector tabs to be 2.8mm thick and…
Use diffusers from ruiqimao's model. I will add that the diffusers did not slide in for me without modification, but I just removed the sidewalls of the diffusers post-print and they slid in a lot more smoothly.
I made a diffuser for LED LED Cover_01 needs to be printed with translucent material
While looking for strain relief for the Bed Heater wires, I discovered that the Siboor part had screw holes instead of cable tie holes. This part allows you to secure the wires from the bed heater to the channel for the Rear Bed Mount…
Still uses the same hardware. pcb should be a snug fit
Instructions: Print using Voron print settings (PETG or ABS, maybe even PLA) Print with face touching the plate. Add supports structures. Print each STL once Print each STL again, but this time, mirrored Clean-up your print and assemble…
Here is my versions of the Stealth Skirts originally made by @PrintStructor!! i have modified them to work on the Siboor Tridents Electrical tray! ive printed them using the Default Voron Specs Layer height: 0.2mm Extrusion width: 0.4mm,…
It only needed a little force to break the standard HDMI5 bracket at the thinnest part (see picture). This design adds a few ribs to strengthen that part of the design, and adds a couple of holes for tool access. Print with the back down.…
The stock siboor plate stops only support exact size build plates. As in, if your bed is 350mm they only fit plates exactly 350mm. After market build plates are typically build size +5mm, so the stock stops will not work. These plate…
The blocks can be mounted with stock screws, however on the X endstop I found that a 2 mm longer screw works better. I run the SIBOOR Trident 350 AWD with flipped Y rails and the following mods from the Armchair Heavy Industries…
In the title you cann read my config. Stock siboor aux are made for stock stealthburner, so i've modded the original for throwing aire in the right direction and not on the build plate. altready cutted for adding bed adesion
Much more robust re-enforced support bracket for Siboor Trident HDMI 5" screen. Still prints great without supports and would recommend printing with strong support settings, namely 4 walls, at least 25% gyroid infill and 0.20mm layer.
these two tools help u to align the pullys as requested in Siboor Docs one is for 13mm the other is 5mm
◼ Voron Trident (AK Stealth Wires) Siboor blower PCB housing hides the Auxiliary Part cooling Fan PCB and the wiring inside the 2020 extrusion profiles for a stealth look, created as part of the AK Stealth Wires project. Learn more about…
The new Design of the Display Holder does not permit to fit the standard Skirts anymore from the official Voron STL. So i made this design. Fits very snugly but perfect. Please share your makes :) This is for the Siboor 2.4r2 AUG kit from…
Micron R1 minisb modified to accept nozzle leds. For example from Fysetc.
These are front skirts to use on a 350mm Siboor Voron Trident and ChriL's screen mount. This is to be used with the Clicky Clack door as well. Follow instruction on livinhack's github to print correctly. ChriL's screen Mount:…
Klipper expander module mount for Siboor/ Voron 0.2 R1 w/ fly mellow gemini 3 board materials: 4x - M 3 screws 2x - M3 standoffs 6mm
Cables most likely need to be routed through the cutout before installing the screws unless you add the connectors/headers later.
An easy-to-install bed cable strain relief for the Siboor BOOM kit. Designed to drop in just as easily as the original stock part, but with significantly better cable support! Installs seamlessly just like the original stock component—no…
◼ Voron Trident (AK Stealth Wires) Siboor stepper cooler helps keep the stepper motors at lower temperatures. Designed specifically for Siboor 2504 stepper motors and for use with a 4010 fan and stepper motor heatsinks, created as part of…
I wanted to mount 2 UHP Power supplies and I didn't have tools to tap new holes in my Bakelite electronics bay base I used these as both a drill template and a mount. Drill 4 holes for one end (2 per power supply) and use the power…
The power inlet on the back has been moved to an unused side fan
I wanted to mount 2 UHP Power supplies and I didn't have tools to tap new holes in my Bakelite electronics bay base I used these as both a drill template and a mount. Drill 4 holes for one end (2 per power supply) and use the power…
Instructions: Print using Voron print settings (PETG or ABS, maybe even PLA) Print with face touching the plate. Add supports structures. Print each STL once Print each STL again, but this time, mirrored Clean-up your print and assemble…