36 models
My house has no gutters and soffit trim that has a lip, so the normal clips won't work. Designed these clips to get my lights up before it got too cold. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No…
Slides over lights mounted on the soffit with the 3M tape. Secures by covering the wire on both sides
OEM mount is a long and gangly pole , too wobbly for me! Too many posts of folks adding guy wires to keep the wobble down. Any wobble at all will offset your yarbo core by the same amount; its supposed to be static! This mount is intended…
Simple soffit clip, but each can provide five or ten pounds of holding force. Make it out of PETG, and you should be able to leave them up all year.
Clip designed for Triple 3-1/3" InvisiVent soffit by CertainTeed to provide for light weight hanging without drilling or strong adhesives. Insert into the vent slot with clip parallel to the slot, then turn to lock into place. Should not…
I bought some white PCB water resistant RGB Strips and wanted to stealthily mount them permanently to my house - to stop with the yearly chore of putting up/down the christmas lights. I didn't trust the double sided tape, so I designed…
Soffit mount for Reolink cameras intended to allow flush appearance and clean cable passthrough on PoE models. I have tested this with CX410 PoE Camera but I believe the mounting pattern is the same for most Reolink camera. The model is…
Inital remix was to 'fix' the original Thing - S3D saw it as 2 seperate parts Then extend the back of the clip by 2mm, reduced the height to 5mm and made the gap for the cable 5mm also
I didnt want to make a big hole in my soffit to mount the turret camera's large connector. This mount allows you to securely hold the Ubiquiti G6 Turret camera in place on a soffit, offering an installation option that avoids drilling…
I was installing some g4 domes on the soffit of my house and REALLY had a hard time getting the camera to twist onto the bracket without bending the soffit and pushing the mount higher. I made this bracket that screws into the soffit and…
Avevo esigenza di avere il controller Xbox a portata di mano, quindi ho disegnato con tanto di logo lo stand. Il fissaggio è molto semplice, con due viti da 4mm di diametro, e la facilità di passare il gira vite tra i fori, senza rovinare…
I needed a way to clip my Starlink cable under my soffit. I have a trim piece that was perfect for an anchor point so I designed this simple clip for the purpose. It is designed for a 6.5mm cable and a 24mm wide anchor piece.
This vent cap is designed for mounting into the soffit to deflect the air away, reducing the opportunity for warm humid air to circulate back into the attic. The vent body includes an optional bug screen, and it can be installed as-is or…
Lampada da soffitto in più componenti, facile da montare con colla
I don't know about you but I hate the look of metal soffit vents. Especially with and beautiful stained wood soffit… Well, don't compromise your beautiful soffits - make the vents with the same material! This guide is intended to be used…
3D printed clips to attach WS2811 Pixels in J-Channel to the soffit for Permanent LED Lighting. Printing: Clips: PETG or ASA - .3mm at 20% infill Drill Guide: PLA - .3mm 20% infill stand on end (will fit on Prusa MK3s size printer) Clip…
I needed some hanging hooks for my string lights outside and couldn't find anything that would work for me, so I made a hook that would loop into the soffit brace for the soffit (roof vent). These worked out nicely so I thought I'd share.…
Dial in your first layer to prevent the elephant foot effect from constricting the holes, or clean them up with an exacto blade after.
my PTZ g5 and g6 soffit installs needed help. the g6 is significantly larger and heavier than the g5. I made this bracket, simliar to my g4 dome bracket to make soffit mounting more manageable. This plate should be printed in something…
Installed a tongue and groove ceiling on my porch roof and I needed to drill 1,000,000 holes for ventilation. So I print
A 2 piece clip system when placed together create a non-permanent way to hang year around pixel lights, mounted in J-channel, to the eaves (soffit actually I guess) of your house. The attachment created when the two pieces are slide…
Designed to snuggly fit the wyzecam flat usb cables.
Plafoniera a 3 luci per soffitto. si installa a soffitto per mezzo di un solo tappo e una sola vite (al centro). perfettamente adattabile al set di cavi e lampade sospesi della ikea tipo gravacka, jallbi, skaftet. oppure con qualche…
Soffit Eave Oval Vent. It has 3 files, one all combined and the others with parts separated so you can remove clips if there are too many on whole model. I spent a couple days making this and I hope you all enjoy. Final printing is in…
Mount your Reolink Trackmix inside your soffit, allowing you to minimize it's visible footprint. Note: If your camera is mounted like mine in the soffit, the IR lights may become useless as well as the spotlight due to the splashback from…
A 2 piece clip system when placed together create a non-permanent way to hang year around pixel lights, mounted in J-channel, to the eaves (soffit actually I guess) of your house. The attachment created when the two pieces are slide…
Block glare for security cameras that are blinded by street lights or sunlight during the day, and even block IR lighting emitting from other cameras. Could also be used to block irrelevant areas of the camera view that trigger too much…
This 8" soffit duct vent is designed for clean, functional ventilation using standard 8" flexible ducting. The design includes dual swing doors that help prevent backdrafts, pests, and debris from entering while still allowing proper…
Initially I thought this will just be a plate with few screw holes, but my roof soffit panel is extra long (360mm to be exact), so I cannot fit it with my printer. Given the camera is quite heavy, and I want some flexibility to adjust the…
Remix del modello da parete adattato al soffitto. Usare una rondella da 25 mm ed una vite a pressione da 6mm, il foro inferiore permette l'accesso per avvitare la vite al soffitto. Consigliato ASA o PA6.
if your lilke me and dont want to change your light juste for a rusty cover , this will do =) i have a old house and didnt feel like changing all my 5 soffit lights. it cost around 40-50g of filament per cover , i hope this will be useful…
This is a bracket/mount for the pixel trim found here: https://yourpixelstore.com/product/yps-pixel-mounting-trim-great-for-outlines/ I screwed these to the underside of the eve/soffit of my house with #8 1-1/2" screws. Printed in PETG.…
Non-destructive mounting clip for securing WS2812 LED strips directly to exterior trim such as soffits and fascia boards, without staples, screws, or adhesive. Its calibrated snap-fit tension holds strips in place against heavy winter…
Slides over lights mounted on the soffit with the 3M tape. Secures by covering the wire on both sides
OEM mount is a long and gangly pole , too wobbly for me! Too many posts of folks adding guy wires to keep the wobble down. Any wobble at all will offset your yarbo core by the same amount; its supposed to be static! This mount is intended…
A soffit mounted seed pixel clip with an 18 gauge 3 wire cable clip on the back. Print in place, no supports necessary.
