72 models
Without a spool, the Sunlu S2 is very top-heavy and can easily topple over. This is a very simple stabiliser which is mounted to the case and provides a bit more stability. It does need longer screws, I used 18mm long which I happened to…
I like to have a Z-Axis support for my Ender-2 Pro, keep the handle and move the filament holder from the side to the top to save some desk space. The Z-Axis stabiliser requires one 608 Bearing (22mm).
I added tabs to Upper_Bracket and now fits on the original screws from the printer. You need: 2 x Upper_Bracket 1 x Z_Axis_Lower_Bracket_SWX2_Part2 1 x Z_Axis_Lower_Bracket_SWX2_Part1
Friction fit base stabilisers for Arcs miniatures so they do not topple easily, no glue needed. To fit the main ship bases the slip the angled front base from the back of the ship and slide until the angle of the printed base matches the…
Update 6th of March the w.i.p. status has been removed from the stabilization system use two sticks and one clip (tight) to create a stabilization beam. The ML4 stabilizer ring is only applicable for the Motorized Lift v4 The ML4…
Required hardware. 2x 1000mm m10 threaded rods cut to 500mm each 16x m10 nuts 12x 16mm m5 allen bolts 12x m5 t-nuts
This is a remix of my frame stabiliser for the Voron V0 now made to fit the Voron 2.4 frame size. I have beefed it up to add extra rigidity as the frame size is much larger than the V0. But still keeps a small form factor to sit neatly in…
simple handlebar stabilizer max supported diameter of the handlebar 40mm max supported width of the main bar 50mm i recommend to add a thin layer of rubber at the position of the main bar in order to prevent damaging the surface of the…
See my improved model here: https://www.printables.com/de/model/961036-z-axis-stabiliser-for-sidewinder-x2 Fully printable Z-axis stabiliser. Perfect fit for Artillery Sidewinder X You need: Right Side Right Top, Right Bottom, Middle,…
So the stock rubber feet for the MK3 leaves your printer wobbling all over the place, the hard feet are great but make your printer a lot noisier. There has to be a better solution right? This is a designed to hold the stock rubber feet…
So my bed had a bit of a wobble from a bad linear rail block, so I replaced the block, problem was the replacement was just as bad as the first one. Or my rail has some really bad machining. Anyway to avoid spending more I designed this.…
I needed to lift my washing machine about 40mm off the ground, hence my own custom washing machine foot stabiliser. Printed from TPU, this should prevent movement and reduce vibration. Recommended to be printed with TPU and at least 5%…
Voron Frame Stabiliser (MINI edition) Building from my Hex Stabilisers i wanted to create one that had the same benifits and style but this time being a little smaller than the norm. shaving off 14mm in length has made this a neat little…
VORON V0 ELECTRONICS BAY STABILISER This is a small but mighty little addition to your V0 making things that little bit more rigid! I've used these for nearly 2 years now and they have stood the test of time and multiple trips in the car…
If you have carbon wheels and use long presta valves you will be familiar with the problem of valve rattle at higher speeds. No drama - just annoying. This is an example of how it is simply fixed with a small stabiliser. This is precisely…
I remixed this model so that larger tools can fit through the handle holes to screw it down. I also made it longer to be more ergonomic. I also flattened the bottom to help improve printing. I usually print with a 0.4 mm nozzle at 0.16mm…
You're out at a restaurant, and you got the wonkiest table. Moving the table just made it worse, hahahah! Folded paper napkins never seem to quite do the trick. Everything else you might be able to use is of course at home or in the car.…
I wanted to reduce the screen vibrations on my R1250GS and keep the functionality of easy height adjustment and access to the GPS navigation locking system. I didn't like the commercial options. The system clamps onto the BMW GPS mounting…
same as original but made it a bit shorter & mirrored
I have constructed a simple holder for drink cans so that they do not tip over so easily on unstable surfaces. It fits normal beverage cans with a maximum diameter of 66.00 mm. So all normal 330ml or 500ml cans. Otherwise, of course, any…
This is a little stabiliser pin for the XS Fan Duct Plate from Dev-In Labs ( https://www.printables.com/model/251191-ender3-adapter-for-e3d-revo-hemera-originalxs-v2 ) which can be used to mount Hangtight 's fan duct (…
This is an inkwell type support for the screw top stylus support supplied with the XP-Pen Innovator graphics pad. I wanted something to support and give some weight to the screw top pen support and designed this simple thing in Fusion…
A block for the barrel to keep the layer lines from separating and reinforce the hand guard.
A little block that doubles up the mounting point of the x-axis rails where they connect to the Z-Axis. With the original mounting blocks I found that it is possible to rotate the sheet metal piece around the z-axis, affecting accuracy of…
Dry Box PTFE Filament Roller/stand with Stabilisers Note: to fit the Gunpla specific cereal boxes (they have hexagons on the lid), i cannot comment if it will fit other, please check the Gunpla requirements This all came about due to not…
A simple device to add stability to your camp stove when cooking on uneven ground. Five legs work better than the three-legged versions available commercially. The legs fold up underneath into the concave bottom of the can so it doesn't…
You know the feeling... A new table from Ikea (Lack) and a tiled floor that is not level :-( Here's the solution: the Ikea Lack stabilizer. Print 4 feet, if you use ABS your table is also protected against water when cleaning the floor.…
The laptop stand from https://www.printables.com/model/1316274-laptop-stand-with-cable-management is really nice, just the balance is off so I created this foot. You will need to mirror the file to print the right side.
Mount with existing screws on the charger. Its quite snug, may need a some convincing push in/out at first with a less tuned printer. Onshape link
While drip tray is fairly stable if you place it atop a scale, I wanted some peace of mind while pulling espresso and swapping cups around. This model uses a 6 x 3mm magnet to attach the base to the drip tray. I've also uploaded a taller…
A stabilising wrap to sit underneath a drink bottle so that it doesn't tip over easily when placed on a desk / bench.
Replacement for broken Caravan RV Stabilizer Stabiliser Big Foot
Update! There's a beautiful detailed remix by lechuckgl here: https://www.thingiverse.com/thing:3753434 Volcanicus is awesome, but one of the downsides to this massive robot made from smaller robot dinosaurs, is that Swoop's legs can…
This part is designed to help remove almost all left-to-right wobble in the barrel of the WE Apache. Front to Back Wobble I have included provisions for a M4x4 or M4x5 grub screw that you install from the front that you can loosen until…
A few of my stabiliser shims blew away in a gust while rigging up so I designed some replacements. I added in 0.75mm and 1.25mm shims to this set as there were times that the standard phantom 1.0mm shim felt like it was not quite right…
A replacement foot for a stabiliser leg on a camper trailer. Printed with 100% infill in PETG.
print with 3 perimeters and honeycomb infill, no bottom and top walls if you want cross section visible or print it with top and bottom closed. Prototype on picture.
The UFix System External fixation is a common technique for treating bone fractures , however commercially available systems remain prohibitively expensive and reliant on complex supply chains, which causes significant challenges in…
Printed in TPU for flexibility and strength I made this grommet to prevent the tubing I use to pump oil out of vaccum pumps from slipping out of the waste drum being filled.
This is a rather “niche” project, but many years ago I bought a Rolson folding trolley which is great for carting bags of compost from the car to the other end of the garden. It has always bugged me that sometimes the wheels try to…
A replacement part that fits the standard Geli balcony planter that stabilises the middle portion of the planter. https://www.bauhaus.info/balkonkaesten/geli-standard-balkonkasten/p/20250991 This stabilising part breaks ofthen or does not…
Celestron Leg Stabilisers Case - Holds 3x Leg Stabilisers
Remix of both Suddoku's Ender 3 cable chain XY endcap https://www.printables.com/model/408734-ender-3-v2-neo-chain and Sout3's Ender 3 V2 Z Axis Supports https://www.printables.com/model/220808-ender-3-v2-z-axis-supports allowing for the…
CR 10 SE lead screw mount replacement
This tool is designed with the strengths of 3d printing taken into account, which some others I have seen do not. Really useful for tweaking and tuning a stabiliser wire that's not sitting straight and plenty strong. Photos show just how…
Large format bed slingers suffer from instability and Z wobbling especially at high heights. There are models online of stabilising rods for the CR-X's cousin (CR-10) but there are none for the CR-X - until now! These rods (and triangle…
Print settings: Spiral vase mode 0.8mm wall thickness (standard 0.4mm nozzle) Single wall Original design file here if you want to modify:…
UPDATE V5 - Added RIGHT Brace to support Logitech Cams - Brio100, C270, etc UPDATE V4 - RaspiCam Case - Added one more version that is flipped 180 degrees to have slightly more height - 5mm approx and added a ribbon guide UPDATE V3 - for…
170mm in length and adapts to 10mm foam/balsa sheets. A version of horizontal stabiliser connector I built to enable removable Horizontal stabiliser for my RC airplanes. The intent was enable me to remove the stabs for storage,…
My Dopper water bottle was too loose, which can be dangerous. This stabiliser makes sure it doesn't flop around in the center console.
Modified design of Mate X Rear Mudguard support brackets with longer length. Three extended sizes are listed here - 10mm, 15mm, and 18mm longer than the original design. The 18mm extension works best for my early build China Mate X 250+.…
I designed this holder / stabiliser for the Philips RC620X1 flashlight. The model stabilises the work light when there is no metal surface for it to hold onto. Without a stabiliser, the lamp easily falls over and is frustrating to work…
Original model 3D model can be viewed and modified at oshape.com “ DJI O3 CAMERA AIRCRAFT RUDDER TAIL MOUNT VOLANTEX PHOENIX 2400”
Milled an old pentium heatsink to cool my Pi and was concerned it might short something out so made this little guard to provide a more stable platform around the CPU, assorted holes around it to clear the tiny surface mount components…
Ball and claw coffee table base stabilisers 150mm
Could not find a item to do this so decided to design this myself will need tweeks.
My Wish Adapter Bag kept bending in my Backpack and the Adapters got mixed up. With this Stabiliser you can solve it. The Plate fits in the big Pocket and is 245x180mm Printed In PET-G 100% infill. Maybe it works with less but i wanted to…
The Swing Stick made by Swing Vision is great for recording your 3.0 tennis games but, it is really made for US tennis courts… Here in Hong Kong where I'm living currently, the fences are so tall and I rarely get to use the “fork” to hang…
Parts Needed M8 Nut M8 Bolt Self tapping wood screws x 2 Print Instructions Pause at layer 192 to insert M8 Nuts
Self explanatory model. Use (up to M6) screws to tighten everything in place. Print the pivot piece with pointy side of the hole pointing up. You might want to shorten the pivot or ideally use a kid's bike fork.
I decided to hang a few of my guitars on one of my doors, but I soon realised that the guitars would sway all over the place and even sometimes fall off when using the door, so I designed some simple guitar stabilisers, works really well…
Overview This printable stabiliser reduces the torsional flex that makes a telescope tripod rotate around its vertical axis whenever the mount is touched. Three diagonal struts join the legs in a closed loop; split clamps make the system…
This is a 3D-printed stabilizer support designed specifically for mounting an automatic focuser (like the ZWO EAF or Pegasus Astro) to the Takahashi FCT-65D refractor. The factory rack-and-pinion gear cover on the Takahashi FCT-65D only…
This a cupholder to prevent my young kids from spilling their drinks all over the table. I printed this in TPU for extra grip.
For my Ender 5 Endorphin Hybrid CoreXY build, I noticed that tightening the bolts for the X-Axis idlers causes binding in the bearings, leaving the idlers locked. So I cannot fully tighten the bolts. This created wobble in the idlers.…
Parts Needed M8 Nut M8 Bolt Self tapping wood screws x 2 Print Instructions Pause at layer 192 to insert M8 Nuts
UPDATE V5 - Added RIGHT Brace to support Logitech Cams - Brio100, C270, etc UPDATE V4 - RaspiCam Case - Added one more version that is flipped 180 degrees to have slightly more height - 5mm approx and added a ribbon guide UPDATE V3 - for…
Could not find a item to do this so decided to design this myself will need tweeks.
I decided to hang a few of my guitars on one of my doors, but I soon realised that the guitars would sway all over the place and even sometimes fall off when using the door, so I designed some simple guitar stabilisers, works really well…
While drip tray is fairly stable if you place it atop a scale, I wanted some peace of mind while pulling espresso and swapping cups around. This model uses a 6 x 3mm magnet to attach the base to the drip tray. I've also uploaded a taller…
