29 models
If you're looking for a little visible reminder of things that need to be done this might be the model for you. The list comes as a set of 2, 4, 6 exchangeable tasks. I am using a strong double sided tape to glue it to the wall. The task…
Switchable Magnet. Center: 17.5mm turned down from .75" all thread Outer bars: 3/8 (9.5mm) Magnets: N42 10x5 This is a tad different than the design created by Andrew Klein. It is smaller, the outer "bars" go all the way through, and only…
Desk-Organizer with switchable Addons to play during breaks.
Switchable Magnet remix. Center: 12 mm rod Outer bars: 6,5 mm rods Magnets:5x4 mm (doubled up) Made this remix only to fit materials I had at hand.
The scepter is divided into multiple parts, allowing you to choose between an engraved or plain design. The gem is mounted via a screw, and it is possible to print multiple gems with different materials and switch them as needed. The best…
Project Description: These 3D Printed drawer labels allow for paper labels to be easily switched out while the label housing keeps a low profile to the drawer front. This system is to label drawers and cabinets. It is design to be glued…
My original idea was to create a small box that I could stick some LEDs in… haven't made it that far yet, but this turned out to be a nice little décor piece. If you do want to try this as a light box, I would recommend increasing the…
This cover protects the DC House 12V 100Ah terminals and provides some extra functionality. The cover clamps securely onto the battery but is easy to remove if you need access to the terminals. Its printed in PETG , I used Overture PETG…
Print as rotated in the STL-Files, obviously with “Support on Buildplate” I “glued” the Plates to the window using Tesa Powerstrips (2 for the short and 3 for the long one), holds perfectly for over a year now. You need a Plate for the…
This is a model of the MAGSWITCH MAGMOUNT 150 GRIPRIGHT 90 DEGREE SWITCHABLE MAGNET - 81001424 https://magswitch.com/collections/new-products/products/magswitch-magmount-150-gripright-90-degree-switchable-magnet I needed to attach…
Uses a male JST-XH 3-pin connector on the bottom to connect to the printer body and a female JST-XH connector on the top to connect the lightbar cable into. In the center of the plastic part (cf. 2nd pic), the middle pin is soldered…
This is an alternative pen arm for the Sphere-O-Bot. https://www.thingiverse.com/thing:1683764 It allows to easily swap between pens while doing multicolor creation. You need at least 2 6x2mm magnet, more if you want to print more pen…
This is a quick-adjustable corner edge guide using a switchable magnet. Works best with 2 magnets on steel honeycomb. The magnet can be fastened to the guide with M5 screws if needed. The part will fit on a Bambu X1C. Print…
Motivation I found this nice model of "Helferlein / Little Helper" by DIY Wizard (based on the popular model "Dummy 13"). To illuminate the bulb you can order a magnetically switchable device ... which I did not have available for a short…
Switchable arrow I made to use in baby crib, so we remember how we positioned baby to sleep. Insert should be printed in a different colour.
This is a quick-adjustable straight edge guide using a switchable magnet. Multiple magnets can be used, but 1 in the center is sufficient. The magnet can be fastened to the guide with M5 screws if needed. 6mm OD x 12 mm L pins may be used…
I'm happy with my automatic door closing mechanism but sometimes the door snap shut and my two Cats might get uncomfortable if they can't leave the room anymore. So I searched for a small door stopper which could be easily replaced if not…
I have Jung LS 990 frames all around my house, which are nice, but most third party devices, especially smart switches and such, are made for the Gira 55mm system. I created a simple adapter plate here . This is a two part model, where…
So you got your CPAP WS7040, and pondering on whether you're mostly wanting fresh cold air, or avoiding cold drafts? Let software handle it for you. This (significant) mod of my favourite side bowden entry has been fitted with a 2…
Use Emboss option in your slicer to add Your name to nametag
Wired Ethernet switchable 2-port power outlet with full local control from your web browser or via your smart home with the usage of prepared URLs. It uses the WT32-ETH01 ESP32 board which allows using ESP32 controllers connected to your…
I saw that Adafruit had published a 3D printed case for their soldered version of the HUSB238, but not the switchable one. So I made this real quick to help with a project I'm working on. This uses four M2.5x4mm screws to hold the board…
This was migrated from my Thingiverse profile and is from 2016. Hot end heat sink enclosure and ducts for Ormerod 2 quick-set dual-nozzle setup with dc42's improved differential infrared height sensor board . A removable shutter allows…
I was looking for a way to automatically switch my cocktail table joysticks between 4 and 8-way mode. I found Legochuck's model on Thingiverse ( 4-8 Way Switchable Sanwa Joystick Restrictor Plate by legochuck - Thingiverse ). My joysticks…
Needed to finish: 2 M3x6 button head screws Superglue Did print well following RatRig Printing instructions in PETG. First mount the valve to the top section with the M3x6 screws. Use some supper glue to fix the screw on the lever side,…
Headphone Holder for IKEA SKADIS Remix This bad boy now comes with magnet holes designed for 8x2mm neodymium magnets. The holes are measured to exactly 8x2.1mm on the Headphone holder, but how is that possible? It won't fit you say? The…
Use Emboss option in your slicer to add Your name to nametag
Motivation I found this nice model of "Helferlein / Little Helper" by DIY Wizard (based on the popular model "Dummy 13"). To illuminate the bulb you can order a magnetically switchable device ... which I did not have available for a short…
Switchable Magnet remix. Center: 12 mm rod Outer bars: 6,5 mm rods Magnets:5x4 mm (doubled up) Made this remix only to fit materials I had at hand.
