35 models
🧵✨ If you are tired of struggling with re-threading drawstrings on your clothes, you need to try this 3D printed version of a Drawstring Threader ✨ Available in five different widths (6mm, 9mm, 12mm, 15mm, and 18mm), our threader needles…
Print approx. €0.13–€0.16 excl. taxPreliminary estimate for one variant
magnetic threader ring or keychain helps run cables and other wires behind walls and through tubes. fits a neodymium magnet dimensions listed on STL keychain version requires a keychain around , feel free to replace keychain with anything…
Print approx. €0.83–€1.02 excl. taxPreliminary estimate for one variant
One side is for M12 other for M6 4 perimeters 50% infill PETG
Print approx. €0.39–€0.48 excl. taxPreliminary estimate for PETGSource material: PET
If you've ever needed to re-thread a drawstring for a hoodie, you know it can be tricky. After struggling with this once I designed these drawstring threader needles to make the process much easier. Simply pass the end of the string…
Sized inspired from commercial elastics threader. Easy and quick to print, a must to have in your sewing toolbox. I have added a version with holde to allow cords or round elastics insertion. Can be print in PLA or PETG
Have you ever accidentally pulled the drawstring out of your favorite pajama pants? Trying to push a floppy string back through a long fabric channel just so you can keep your pajamas tight along your body can be incredibly frustrating.…
This is the ultimate flat elastic threader ! I have always struggled with the one-size-fits-all elastic threader, because it just either didn't grab the elastic tightly enough or it didn't fit in the tunnel for elastic. This is a set of…
Next time the drawstring comes out of your garment, instead of struggling to get it back in, print this model and easily fead it back through (almost like a giant needle!). This is very fast to print and uses very little filament. This…
Designed for nozzle size 0.4mm but can be changed in the provided OpenSCAD file. Best printed with 0.10mm layer height (The eye part is 0.3mm high). Also, tested with 0.12mm though model scaled to 106%. No adhesion, no supports.
Here is the model of a solid needle threader which can still be used 9 times if it breaks. Prints quickly and uses only 1 gram of filament. Perfect for spool ends. Here are the step to use the model. Thread the eye of the needle into a…
ever pulled that string on your hoodie or your PJ pants a little too far and now it's out? you can try and rethread it with a safety pin or a straw or just loop or tie it to this tool and thread it right back in under 30 secs. the pencil…
My son loves his blades but I wanted to design my own. I couldn't find any that were print in place unless they were 2 pieces that needed to be screwed together. All my designs are print in place with no supports needed. I generally print…
The small circle at the end of the thin line of filament helps keep the line attached to the print bed during the print and does not affect how well it works through the eye of a needle.
Robust drawstring threader that cannot break appart.
This generator will make all common size elastic threaders (also known as tape threaders and bodkins). It will also make a drawstring threader for round cord. How to use the Generator You may customize just about every dimension to create…
Have you ever pulled to strong in your waistband cord or hoodie cord? This is a basic waistband threader. For threading your cord into the waistband or your hoodie. I still have to figure out how to effectively get the cord hold onto the…
The needle Threader from episode #301 of stargate SG-1
Use to (re)thread strings through clothing like hoodies!
Thread as many needles as you can onto the ring. Coil a piece of cotton around the hooked tip of the ring and pull off the needle to have it threaded and ready to sew with. This needs a finely tuned printer. I'd suggest printing several…
needle sits in the groove at the top and thread starts at 4mm hole and funnels down to 1mm to find the eye of the needle. Printed at 0.2 layer height with 0.4mm nozzle with PLA on creality k1
This is very bad so I don't expect anyone to use it. I made this so I could thread my hoodie strings back in.
I've used 0,25 mm Kynar electrical wire. Must be printed at 0,1 mm layer height to preserve wire channel size. Set a pause at 1,80 mm layer. Make a 0,8 mm loop at both ends of the wire. Wrapping once or twice around small tweezers should…
Easily thread the string back into your hoodie. Includes a hanger so that you can store in your closet. Print instructions no supports needed.
Intro I designed a needle threader which can also be used as a versatile handle for small tools (mini chisels, cutters, scrapers, etc.). Thanks for visiting! Once you've printed the handle, you'll need to perform some additional assembly…
Makes replacing the tie string on your BJJ or Karate gi pants easier. Works with the giant zip ties that you can find at your local home improvement store.
Printed in Devil Design PET-G on a Voron Switchwire (converted Ender 3 Pro) at 0.2mm layer height, 15% cubic infill.
The Knob for the needle Threader Brother Innov-is F400, might also fit for other brother sewing machine see the pictures. The print is a press fit, you might want to use some glue, and if the bridging doesnt work to good use a file. Needs…
Small tool to help getting drawstrings or rubber bands through holes: Hook or slot for holding on to rubber band or string. Scale it up in slicer if longer or larger tool is needed.
Problem: The printer is positioned close to the wall, making it very difficult to thread the filament into the small opening. Solution: To make this easier, I designed a cover with a “funnel” as a threading aid. Nothing needs to be…
This tool head is shaped to slide over all standard pallet slats and works with the flexible dryer vent cleaning rods I already have. Designed to print with no supports. I printed in black Overture PETG, 0.2mm layer height. It uses M6x0.8…
Printed in Devil Design PET-G on a Voron Switchwire (converted Ender 3 Pro) at 0.2mm layer height, 15% cubic infill.
If you've ever needed to re-thread a drawstring for a hoodie, you know it can be tricky. After struggling with this once I designed these drawstring threader needles to make the process much easier. Simply pass the end of the string…
Thread as many needles as you can onto the ring. Coil a piece of cotton around the hooked tip of the ring and pull off the needle to have it threaded and ready to sew with. This needs a finely tuned printer. I'd suggest printing several…
