Ikea Strimsäv magnetic holder
This is a simple magnetic holder for Ikea Strimsäv light. There is open space for 12mm magnets. Just put a drop of glue and put some magnets in the slot.
- Downloads
- 30
- Likes
- 6
- Rating
- 0
Counting matching models…
This is a simple magnetic holder for Ikea Strimsäv light. There is open space for 12mm magnets. Just put a drop of glue and put some magnets in the slot.
More spare parts available: Air conditioning trim pack https://cults3d.com/es/modelo-3d/variado/air-conditioner-trims-for-seat-ibiza-ii I also have several spare parts for Seat Ibiza II: Spare hinge for the trunk tray:…
You will need: 1x support 3x clips 1x Screw Printed in 0.2mm layer height with 0.4 nozzle
If like me your Tool Holder handles didn't look very good after removing the supports, I designed these handle trims to snap straight onto the Bambu Lab Tool Holder handles to improve the aesthetic, especially if they are printed in the…
Lithophane STRIMSAV IKEAK LED SPOT Compatible with 15x11 cm and 15x10cm 60° vertical lithophane. The support is in two parts so you can use the top part and adapt it to another lithophane support. The spot is attached with clips (stl…
The Keychron K2 HE (special edition) has wood trims on the sides. I want to create storage space for the USB dongle, this is step 1; recreating the trims. Edited on Jan 22 after feedback from Drazor; my models were 127 mm long, whereas…
Warning A multi-color management tool is required. The yellow parts are not included. You must purchase the 3D SETS models 7 and 8. The configuration in the slicer must allow the added elements to be printed in place of the original…
The original model use light bulb for light source This base able to use Ikea strimsav led as light source Support required for printing
A table lamp made for ikea strimsav. Press on the column to turn the light on and off layer: 0.2 infil: 15% supports: yes
I have designed and 3D printed a lamp shade to be mounted on a LED light usually installed in BILLY-bookshelves from IKEA. It prevents glare when turned on and gives a nice, comfy light. Mount it by sliding the opening towards the…
I searched a neat way to use the Strimsäv spot as a small workshop lamp. To build this print you adittionally will need: 1x screw M4x10 (at least, but longer ones will work, too) 1x M4 nut slice with 0.2mm, 3 layers, 15% infill, no…
Its all the armor trims from minecraft
Layer height 0.2 The lamp cover is made for IKEA Strimsäv Art.No 405.683.02 or 705.224.78 You can stack several Middle units. In the photo there is one transparent and one red Middle.
Simple stand I designed for my girlfriend to hold her razor to help keep it dry. It has a convex base to (hopefully) allow the water to drain away from the razor, and a lip on the edge to stop the water from running onto the shelf.
These where designed for vintage Technics speakers (circa 1985). Especially for the SB-2565 model speaker tower. Its close copy not exact replica, so they would have to be printed in pairs to keep the look.... . Added one for the stock…
This is a desk LED lamp that can be usefull when you need som extra light for Tinkering, soldering etc. The Housing is designed for IKEA STRIMSÄV LED-spot IKEA part number = 705.224.78 The stand used in this design is from the Simple…
Why? I tried to mount the LED pads to the top covers using the adhesive tape that came with the pads, but after a few minutes of heated printing, they fell down. Additionally sitting near the printer caused the pads to be a bit too bright…
Three different door trims with varying hole sizes to accommodate different bird species for the ‘3-Story Cantilevered Birdhouse 2.0’ model. Diameter of the holes: - 28 mm (~ 1.1 inch) for blue tit, crested tit, coal tit, marsh tit…
Trims Roof Top Cab Marker Light Cover Compatible For 2003-2009 HUMMER H2 SUV SUT
Carefully attach the mount on the gantry as seen in the photos. You will feel resistance, and the intended print orientation puts the teeth at a weak point; but the model is thick enough that it won't snap if your print settings are good…
Wall bracket designed to mount the IKEA STRIMSAV as a reading light.
Печатал из tpu 95a получаются достаточно мягкими чтобы при желании можно было снять или установить без демонтажа накладки порога
Its the coolermaster masterbox lite 5 trims for the top and bottom its really that simple you might want to print them in PETG so it doesnt melt from the computer's heat
About These switch panel blanks fit very well in a Mercedes Sprinter VS30 / W907 OEM panel, to add additional switches to your van with a clean look. Their key design value is the spring/locking mechanism which is similar to OEM Mercedes…
The holder is designed to keep the IKEA STRIMSAV in place, with the possibility to push its bottom side to still use the on/off switch. I created this as addition to the "Minecraft Creeper Lantern" of Freezing Pixels (…
We have tried a number of different Seal trims for our Glass Shower doors, for both our bathrooms. They were all difficult to assemble and were quick to collect dirt, soap rests and deposits inside the trim. Partly due to that their…
Its the coolermaster masterbox lite 5 trims for the top and bottom its really that simple you might want to print them in PETG so it doesnt melt from the computer's heat
https://youtu.be/5h5hcsslLds 16/03/2025 The following improvements were made to the center trim. - The part has been reinforced. - Added stronger flanges than the previous ones. It costs a little more to put it on but it does not fall…