Counting matching models…
Remix of ( https://www.thingiverse.com/thing:3337602 ) Modified to accept a 10x3mm magnet since I had more of those than the 8mm ones. Thanks to HEIados for including a very nicely done Fusion 360 file to work with! To get the 10mm magnet…
Basically prints without support and brim, but I'd recommend a 5mm brim and organic support for the locking interface (as in the .3mf file). 0.6mm nozzle and 0.25mm layer height is fine, although you might reduce it for a higher quality…
Basically prints without support and brim, but I'd recommend a 5-10mm brim (as in the .3mf file). 0.6mm nozzle and 0.25mm layer height is fine, although you might reduce it for a higher quality print. Do yourself a favour and use PETG or…
This is a remix of the Bambu Poop Chute by Fantasy3DPrintsShop , modified to suit my needs This uses 10x3mm magnets to attach to the metal plate on the back of the BambuLabs X1C, P1P and P1S. The support under the end where the magnets go…
These accessories prevent dust or pieces of filament from getting stuck in the Z axis and under the side covers. Modified the original to use 10x3 round magnets. Had issues finding reasonable 20x6x2 and all the 20x5x2 I was getting from…
Read the description of the original and test print using just the man's foot - my printer/settings work for these size magnets with just a touch of glue (they press-fit but one popped out). I also glue the man into the frame and glue the…
Slide box 10x10x3 cm Print settings 0,2mm layer 4 walls 30% infill no supports
Tube for geocache 110mm long and 30mm in diameter. Screw-on tube with alcove to facilitate the retrieval of the logbook. Tube pour géocache de 110mm de long et 30mm de diamètre. Tube à visser avec alcove pour faciliter la récupération du…
Updated (2024 Nov 24) - Several people were asking for my Z-axis parts, so I'm uploading them. The bed required 10mm steel threaded balls to be mounted in the front corners and rear center. Depending on the thickness of your bed, you will…
Bambu Lab Y-Splitter for Magnets 10x10x3mm
Full credits to trutheframe ! I only did a quick change of the hole sizes to fit 10x3mm magnets I had at hands! The original is made for 6x3mm magnets in case you have these. Just fix it to your Bambu Lab AMS, your filament box or…
Found @Edward's model for 10x3mm magnets, but the needed to redesign for spouse-factor. STLs provided for a few cable-bundle sizes. In theory, no support is needed – the magnet hole depths have a 0.3mm tolerance to allow for…
Remix of Samsung Remote Holder - This version has no screw holes, is slightly taller and includes spaced to glue in two 60x10x3 mm magnets to make this a magnetic mounting remote holder. One magnet may have done the trick, but I tend to…
Can be placed on the fridge, metal cabinet, or any metallic surface using 10x3 mm magnets.
Honeycomb Storage Wall (HSW) insert magnets based in the original inserts of the model of RostaP. Combine with any HSW, and all existing accessories to bring a bit more of order to your kitchen (if put in the door or side), or to your…
Repair Lock Pin for Honda Transalp 650 M10x35mm This 3D model is a direct replacement for the original fairing locking pins used on the Honda Transalp 650. It is specifically designed to repair or replace the side panel fasteners, which…
Purge tray for the Prusa XL with three 10x3mm magnets embedded in the part. Sticks to the underside of the steel sheet. Pause the print at Z=3.2mm to add the magnets. Recommended to print using a material with high glass temperature, such…
Remix of Blue's Core One corner plug for 10x3 magnets. Printed in Eryone PETG CF and these magnets https://amzn.eu/d/6dWixJC
Remix of "Rotenso / Midea AC remote control wall mount (Desk stand) - This version has no screw holes and includes spaced to glue in two 60x10x3 mm magnets to make this a magnetic mounting remote holder. Amazon Affiliate link to buy the…
I made these because I needed them. I use strong Neodymium 10x3mm magnets in many of my projects and I hope this model helps you. Please share pictures of what your wall looks like! Make sure you add super glue to the holes before putting…
These are a bit strong and sometimes hold to each other instead of the curtain if you don't separate them carefully. Might need to add a shim to to tighten it up. Or you know, use smaller magnets like the original :)
Poop chute for Bambu Lab P1PP1SX1
This is still in development, but some people asked about it. Updates will follow as I work towards a final version. This is a refined and optimized version of my previous Ender 5 ModMax design . I was looking to improve three aspects of…
This is a remix of the Magnetic Key Box by Michaël Fortin using 10x3mm magnets and also scaling down the width (only) of the sliding cover to 99% as the original I found to be too tight. Magnets should be placed at 4.2mm. The g-code…
Remix of the Buddy3D Cam Ball Joint Mount with magnets with very minor changes to use circular magnets that are 10x3mm, rather than the rectangular magnets of the original model.
A tool for placing magnets so that they are always the right way around. Uses a pair of 10x3mm magnets.
I'm not smart enough to edit someone's STL file for the 300 pack of 6X2 mm magnets I bought, but I do know basic CAD. This is the lazy man fix for this issue I run into multiple times.
I printed the quick release part on a 0.6 nozzle with 0.35mm layer height just for the speed. 0.4 nozzle with 0.2mm would do fine too. The paddle part I printed with a 0.4mm nozzle with 0.15mm layer height, as the top is quite thin. I…
A purge bin for the CoreONE system, equipped with a cutout for a wiper and designed to hold 3 10×3 mm magnets.
Kinda bummed that your Vortex Solo 10x36 monocular didn't come with any lens caps? Well I've got you and your glass covered! This is a protective cover for both the eyepiece and the objective lens. They need to be printed from TPU or…
I made this for an other project of mine, where I needed to take measurments of the inner bottom diameter of some conical flowerparts. Just use this device for grabbing dimensions, so that you can hold the caliper on a ruler to get the…
A quick 20x10x3 magnet remix of ccc888 's LACK door knob with inserted magnets . I ordered 20x10x2 magnets from Amazon but got something around 19.5x9.5x2.8 instead, so I tweaked the STL file a bit to make them fit. I used a drop of glue…
easy to print (bridging will be required and PETG or higher is recommended for best results. It's been printed and tested, i just haven't updated the picture just print and snap into place
Bambu Lab Y-Splitter for magnets 20x10x3mm. Normal and mirrored version.
A simple knob to put your magnets in so that they're easier to handle. Fusion 360 file included if you want to adjust for another magnet size.
Print in ABS/ASA, use supports. Edited in FreeCAD
Remix of the charger cable winder with extrusion added to glue in two 10mm x 3mm magnets. Prints exactly like the remix I'm adding two versions, the one I printed in the pictures and a second version I shortened by 4mm
A remix of the original mag flip desk toy using 3 10x3 mm neodymium magnets. I've also added a small 2mm pin to assemble it as I didn't have a 2mm rod on hand. The holes might need a little working with a drill bit when using the printed…
I recreated the original doorknobs from the LACK enclosure, but I included set screws to secure them in place, and I included magnet slots for 10x3 disc magnets instead of the bar magnets from the original. I also included a hole…
X_Belt - allows use of stock belt & mounting screws but will allow easy tension adjustment of the X axis belt - printed with 3 perimeters, .2 layer PLA (Updated 01-09-2019) - better belt locking, more adjustment PM-C07_Z_bracket - has…
🧩 10x3 Puzzle The puzzle consists of ten identical pieces and a storage box with a sliding lid. Assemble the pieces into a ball pyramid. 🖨 Print Settings Print 3v.stl ten times. Each puzzle piece consists of two parts that need to be…
Pegboard-able circles for mounting magnets or magnetic items. Like metal rulers or lite tools Made to have 8x3mm or 10
Binocular Adaptor - iPhone 15 Pro Max - for Diamondback Vortex 10x32 Binoculars - Easiest to print this model as two seperate pieces and super-glue together. -Added a MERGED file which can be printed using supports, but I find it much…
A simple stand to hold (press-fit) and display these 2022 General Mills Monster Cereals figures designed by pop artist KAWS. Holes for bases are 47x10x3mm. If you want a label or inlaid text on the base (as in the photos), use PrusaSlicer…
Admittedly this model slides down your whiteboard due to the weight of the markers but I keep mine at the bottom of the board anyway so it doesn't bother me. You could add rubber or stronger magnets, I guess. Print with the default…
Chitu Resin Heater Controller Wall Mount with magnet 10x3 version
This remix uses 10 10mmx3mm magnets but works perfectly fine with less. Printed with PETG but PLA should also be fine. Added a small hook to stabilise position Increase the magnet size to 10mm x 3mm round magnets Increased the width in…
Remix of https://www.printables.com/model/205599-itty-bitty-fidget with 3 positions using 10x3 mm magnets
10x3 Knife holder. Expanded to fit my new Sam the Cooking Guy knives which are 410mm long. This is 420mm long.
I edited @AzJake's magnetic sharpie holder to accommodate three 10x3mm magnets because that is what I had. I made the three magnet holes 10.25mm x 3mm because I hate when friction fitted magnet holes or the magnets have tolerance issues…
Voici ma version du support a outils, que l'utilise pour ma CC2, Les aimants permette de la fixé sur la plaque gauche Imprimé en PETG couche de 0.2mm, Activé les supports Sur ce support j'accroche: Les 2 tournes vis fournie avec…
A big 10x37mm bullet inside of an even bigger 18x72mm casing. Kinda useless, since the primer's already been struck, and there's not single gun chambered in this. Not made for multicolor printing, but feel free to try.
A K3 Style Door Magnet Holder 10x3. It is pressfit and for assembly with M3 screws.
TIRED OF THROWING A PARTY AND SOME JABRONI TURNS OFF THE LIGHT SWITCH THAT POWERS YOUR SMART SWITCH BECAUSE YOUR RENTAL WAS BUILT IN 1875 AND HASN'T BEEN UPGRADED SO YOU DON'T HAVE OVERHEAD LIGHTS? AND YOUR LANDLORD HAS THE AUDACITY TO…
Heart Magnet 10x3mm fridge valentines day Use 10x3 magnet
remake of https://www.thingiverse.com/thing:1278048
If I can put filters on my cameras and telescopes, why not my binoculars too? This is a simple adapter that slips into the objective opening of Canon 10x30is binoculars and presents a cutout to receive a 2" filter, eg. some sort of light…
I made this for my 310x310 heated bed. Total dimension is 290x290 and dimension between leveling nuts is 245x245. I made it for standard LM8UU bearings and under every bearing slot are 2 holes for zip ties. Everything Except Middle needs…
Added space for 4x Ø10x3 magnets to each model. The cutouts are quite snug, so the magnet should fit without the need for any glue to keep them in place. Print settings: - Lipstick Red PLA - 0.4mm HF nozzle - 0.2mm layer heights - 15%…
Set a pause at 3.2 mm to insert the magnet. It has just a single .2 layer on each side of the magnet for strongest effect with the tradeoff the top layer to seal it in will look a little stringy
The pocket for magnet can be modified to match printer settings.
Redid the entire thread and kept the same design from the POSITIVE so that we can reuse the LID
Mosquito Net Magnets. Magnets size: D: 10mm, H:3mm As the original, magnets are pressed into the holes and locket with glue(but personally, I use them without glue). The Windowmagnet can be glued on a strong adhesive tape, which is then…
i will update with real photo when done
PETG printed. Slightly wider hole that houses the magnet in a fitting way. The edges below have come a little rounded, so to work with a dremel. It was originally designed not to let the magnets touch each other (deeper seat), but it…
Magpin v7 is my best iteration so far of my design. I use these everyday!
I already lost 2 caches because I attached the magnets only with gaffer tape. Now I took a new approach and used a 3D printed magnet holder where the bison tube can be inserted (glued in). The model contains an “invisible” slot for a…
Rangement pour plaques d'impression 310x310 mm Imprimé en PLA de 0.2 mm de couche.
For me, the 10x3 magnets were all a snug press-fit and no glue was required. But if they are loose or you want a little more security, a bit of CA glue will do the trick. I used these to mount a Hue strip inside my Prusa Mini enclosure.…
Ein einfacher Klappmagnet für zwei Magnete mit einer Dimension von 10x3mm.
Thanks to DrAI for this lovely dovetail jig model. I remixed the 1:7 version to use 10x3mm magnets. Changed the hole size to 10x3mm (actual hole size 10.2 x 3mm). My magnets are 9.98 x 2.70mm (trymag from Amazon). They press in and hold…
Instead of two 10x60x3mm magnets, this model uses six 10x3mm magnets. Magnets can be super glued into place. Depending on the strength of your magnets, you may not need to use all six slots. Use tree supports.
INDX Founders Plaque Magnet Holder / Mount - use two Ø10x3 magnets. Like the original project file, I also enabled supports under the magnet slots to test the PETG model using PLA supports, but supports are optional.
It simply glues on to the Sharpie cap. The 10x3mm magnet should snap in snug, but a drop of glue may also be needed to hold it in.
Just a simple label for PLA+
Quick adaptation of the parent model to support 10x3 round magnets that I have on hand from other printer mods. See upstream instructions here: The attached 3mf file captures a few critical print settings: The two models (also attached)…
3D-printed insert for fitting 10x3 tires on the Ulip Splitrim, compatible with Xiaomi Pro2.
I found it difficult to source 10mm diameter linear rods with a length of 325mm and I am too lazy to cut them, so i extended the original mounts to be able to use linear rods with 330mm length.I found it difficult to source 10mm diameter…
This is only the optimized bottom part. Check out the v2 file for the matching top part and other instructions:
Format: Length: 40mm Width: 20mm Height: 6.5mm Recommended text height: 2mm Required magnet size: 10mm by 3mm Placing the text: The text can be placed with any slicer but you find examples in the .3mf file. If you want the text to be on…
Agriculture, Furniture, Interior design
The 3 USB cables shown are the thickest I have and their diameters vary from one to the other, between approx. 3.4mm and 4.2mm. I made 2 stl files with slightly different dimension where one or the other flexed and grabbed on to the…
Printed with TPU. 25% Fill density. No supports. Attached with a piece of fabric.
The storage tray fits FibroTech, shelf, 110x355 mm. The storage tray, dimensions are 100x350x60 mm. The design is prepared for splitting the parts into two parts, if needed. i have added two locking pins to make it easier to align the two…
This is a two-part 3D printed screw tray modelled in Onshape. The ‘Base’ holds the magnets, and the ‘Tray’ holds the screws. You can connect them with 4 M3x6 screws. I will also add the .step files for each so you can modify the magnet…
It simply glues on to the Sharpie cap. The 10x3mm magnet should snap in snug, but a drop of glue may also be needed to hold it in.
Schlauchanschluss 10x32 zum einkleben.
This is a remix of DvG3DAtelier's "Camera lid remix v2 (round magnets only)" for the Buddy3D camera on the Prusa CORE One. Same improved camera angle, but: - Uses 10x3 mm round magnets instead of 10x2 mm. - Works with the Wi-Fi antenna…
TIRED OF THROWING A PARTY AND SOME JABRONI TURNS OFF THE LIGHT SWITCH THAT POWERS YOUR SMART SWITCH BECAUSE YOUR RENTAL WAS BUILT IN 1875 AND HASN'T BEEN UPGRADED SO YOU DON'T HAVE OVERHEAD LIGHTS? AND YOUR LANDLORD HAS THE AUDACITY TO…
This remix uses 10 10mmx3mm magnets but works perfectly fine with less. Printed with PETG but PLA should also be fine. Added a small hook to stabilise position Increase the magnet size to 10mm x 3mm round magnets Increased the width in…
Voici ma version du support a outils, que l'utilise pour ma CC2, Les aimants permette de la fixé sur la plaque gauche Imprimé en PETG couche de 0.2mm, Activé les supports Sur ce support j'accroche: Les 2 tournes vis fournie avec…
A simple stand to hold (press-fit) and display these 2022 General Mills Monster Cereals figures designed by pop artist KAWS. Holes for bases are 47x10x3mm. If you want a label or inlaid text on the base (as in the photos), use PrusaSlicer…
A big 10x37mm bullet inside of an even bigger 18x72mm casing. Kinda useless, since the primer's already been struck, and there's not single gun chambered in this. Not made for multicolor printing, but feel free to try.
I just needed a 10x3 for my XT60 covers so I used the parametric onshape file to make it.
