Counting matching models…
Well, I had a small tripod, a big tripod and some binoculars… so I figured I could make an adapter for it to fit all togeter. V2: I placed the nut higher up to avoid having to glue it. First time trying to insert a nut during print!…
Electrical Junction Box 80x110x50
This a 48 sample pack of approximately 10x5 cm climbing holds with their molds generated by BH Toolset, an open source Houdini project. https://github.com/JeremSparte/BHToolset Category: Sport & Outdoors
Refer to the original post for further model details.
NEW Version. Cosmetic cleanup and slightly better modelled. Conic fit for Ø 100mm duct. This is parts for ventilation fitting 110x55mm rectangle ventilation duct to 100mm Ø duct. Orientation for print will depend on printer and you may…
This is parts for 110x55mm rectangle ventilation tubes. Orientation for print will depend on printer and you may have to experiment with support. Here is an example of a duct angled 45 degrees for better print result for overhangs. See…
NEW Version. Cosmetic cleanup and sligthly better modelled. This is parts for ventilation fitting 110x55mm rectangle ventilation ducts to 100mm Ø ducts. Orientation for print will depend on printer and you may have to experiment with…
This is parts for 110x55mm rectangle ventilation tubes. See also other 110x55 parts https://www.printables.com/model/840511-rectangle-ventilation-110x55mm-angle-90-degree-upr And a 90 degree horizontal to verticla twist module…
A remix of Tom Stantons design, but I modified the rotor to fit 30x10 millimeter magnets. There are 16 slots.
my local hardware store had only one piece of device mounting frame left in stock, I needed some more, so I constructed one by myself also included a self designed stiffener/connector for the cable duct (picture is showing the first try,…
Insert to combine with a magnet (10x5mm 2,5kg force) for hanging the HSW to a magnetic surface. In my case on the side of my Bambulab printer. 2-3 of these with 2,5kg magnets per HSW panel should hold it, depending on the magnetic…
NEW Version. Cosmetic cleanup and slightly better modelled. Conic fit for Ø 100mm duct. This is parts for ventilation fitting 110x55mm rectangle ventilation ducts to 100mm Ø ducts. Orientation for print will depend on printer and you may…
Solar Filter for Binoculars 15x70 or 20x80 and 10x50 use with BAADER AstroSolar Safety Film (OD 5.0) Use a tap to create a thread for screw FreeCad source Category: DIY
This is parts for 110x55mm rectangle ventilation ducts. Orientation for print will depend on printer and you may have to experiment with support. These models are 3-way links for rectangle ventilation duct 110x55mm If you need a mirrored…
New version. Smaller cosmetic changes for a nicer look. and easier print. These models are parts for 110x55mm rectangle ventilation ducts. Orientation for print will depend on printer and you may have to experiment with support. See also…
This is parts for 110x55mm rectangle ventilation tubes. Orientation for print will depend on printer and you may have to experiment with support. The model is available in two versions (male/female or inner/outer fit). Please note you can…
This is parts for 110x55mm rectangle ventilation tubes. Orientation for print will depend on printer and you may have to experiment with support. The model is available in two versions (male/female or inner/outer fit). Please note you can…
110x55mm ventilation duct wall fasteners and one for 2020 alu V-profile. One of the models require a M3 nut to be inserted together with a hex 16-20mm SHCS (hex socket head cap screw). See also other 100mm and 110x55mm ventilation parts…
Previous years I used permanent marker to make labels directly on pots, but by the time I needed to transplant the seedlings into open ground the labels were washed away or burned out by the sun and I couldn't read them! So this time I…
This is parts for 110x55mm rectangle ventilation ducts. Orientation for print will depend on printer and you may have to experiment with support. These models are 3-way links for rectangle ventilation duct 110x55mm If you need a mirrored…
A remix of the Catch-All Trays / Desk organizer that can hold 12 AA and 4 AAA batteries (or you can simply put 16 AAA batteries)
I designed this nozzle to fit between the wall and the window, in such a way that when the window is open the nozzle directs the air out of the window. It fits a 110x55mm ventilation tube. Category: Kitchen & Dining
This model should work for any 210mmx55mm rear MTB shock. The model is 55mm long with a 25% and 30% indent for proper SAG adjustment.
This is parts for 110x55mm rectangle ventilation ducts. To be used connecting two ducts with a magnetic coupling for easy parting. On the image below, wall mounted duct is connected to a duct mounted to the backside of a Voron 2.4…
Material PETG 0,4er Düse 0,2 Layerhöhe oder nach belieben….. Stützen, auf jeden fall Bitte vom Schieber die Kanten etwas abrunden.
This is parts for 110x55mm rectangle ventilation ducts. Orientation for print will depend on printer and you may have to experiment with support. This model is a 3-way links for rectangle ventilation duct 110x55mm. It was updated on June…
Made in OpenSCAD, uses a small M3x10 screw placed through the hole in the linac. Print with supports for the overhangs on the cylindrical cam, and the linac placed flat on its side. Will need a bit of light oil to run smoothly. The…
recommended magnet size : 20x10x5mm - Neodymium magnet (2 pcs) recommended screw: M3x10 (1 pc) Recommended settings: Default 0,2mm layer height profile, PETG filament, supports are not needed .
A standard rounded shelf for openGrid and openGrid heavy. The dimensions are 110x55mm and a 12.5x8mm cutout has been added to the shelf to support a cable pass through.
M3 slot nut for c-profile with 10x5 inner dimension. This is a simple slot nut that can be fitted to a c-profile with inner dimension of 10mm x 5mm. A standard M3 nut can be put in and normally sticks without glue (depends tolerances when…
When following the instructions to build a RGB Minecraft Ore Lamp , I couldn't find a pickaxe with a slot for the magnet; therefore, I created one. At 100%, the pickaxe is 65x65x5mm and the slot fits, a 10x10x5mm magnet. I also included a…
Lost lens cover for my Nikon Action 10x50 6.5 Binoculars so I printed one. Included Rhino file so people that have it can modify if needed. Printed out of PLA.
J'ai perdu une des protections de ma paire de jumelles. Impression en TPU
This is a simple solar filter for my olympus 10x50 binoculars. You can modify source file if you want to fit this design on another one https://github.com/gshimansky/scad-models/tree/master/solar-filter Print Settings Printer brand: Anet…
This is the best holder I've found for hanging a Polydryer box off my Core One. I made a few changes to Narcorex's model to make it fit my magnets and print faster (see differences section). When printing, be careful since the model is…
Kupne łączniki i redukcje zajmowały zbyt dużo miejsca. Zrobiłem, jak zwykle, swoją wersję.
Remix of Prusa CORE One SKADIS mod with different Magnets for the upper rail (10x5mm cylinder)
Small M3 slot nut for c-profile with 10x5mm inner dimensions This is a simple small slot nut that can be fitted to a c-profile with inner dimension of 10mm x 5mm. A standard M3 nut can be put in and normally sticks without glue (depends…
made this stylish hook made to fit a 10x5.5 plank. i made a version with no holes so that you screw it in from the back. i holds up things super well. I use it to hang up my bands and stuff for the home gym. will aslo work for other stuff.
This is a simple and functional glue-in case for a cylindrical 10x5 mm magnet.
I did not have such big magnets. So I made new openings for 10x5 magnets. Holes are press fit and you do not need glue.I did not have such big magnets. So I made new openings for 10x5 magnets. Holes are press fit and you do not need glue.…
I have x4 5160hv on Driver 3 4 5 6 and normal TMC2209 on Driver 0 1 2 7 for Nozzle brush / Air Flap / Extruder and Z motor I design this because while first opening it's found overheat from some Driver 0-2. so i decide to design cooling…
Needed a way to hold a strong 40x10x5 magnet as well as have some indication of polarity. Print the model pointing up, squirt some super glue in the hole and stick in the magnet.
Customized version of http://www.thingiverse.com/thing:735213 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=735213 Instructions Using the following options: arm_thickness = 2.4 tube_diameter = 10…
I wanted to connect my recuperation unit Mitsubishi Loosnay to shelves with 3D printer. To connect this recuparatin I needed flat pipe and connect it around with no space between, so typical connection which is outside is not proper for…
This is version V3, redesigned for better stability with two mounting points. More versions will come in the future!
The model was created in AutoCAD 2018 – the DWG file is attached. Printed from TPU95A.
Over time, the original covers cracked and broke, and as a result, the alignment of the right tube relative to the prisms became disrupted — the image started to double. I didn’t realize this right away and wanted to adjust the prisms,…
Refer to the original post for further model details.
This is the best holder I've found for hanging a Polydryer box off my Core One. I made a few changes to Narcorex's model to make it fit my magnets and print faster (see differences section). When printing, be careful since the model is…
When modding Dell Optiplex 7020, there is not enough clearance to "bend" PCIE cables with larger GPUs. This mod provides 10mm extra clearance and little extra ventilation for fitting larger GPUs into an Optiplex. Comes with two parts, the…
This a 48 sample pack of approximately 10x5 cm climbing holds with their molds generated by BH Toolset, an open source Houdini project. https://github.com/JeremSparte/BHToolset Category: Sport & Outdoors
I needed specific angled connector pieces for my in-house mechanical ventilation. Since the original parts were made from ABS, I decided to design and print the pieces; I have made a variation of adapter pieces (please visit my account)…
I needed specific angled connector pieces for my in-house mechanical ventilation. Since the original parts were made from ABS, I decided to design and print the pieces; I have made a variation of adapter pieces (please visit my account)…
Brackets for using IKEA Nojig bins on Skadis pegboards, using the Skadis Universal Hook by CSD_Salzburg. The hook can be found in https://www.thingiverse.com/thing:2853257/files as Skadis_Universal_Hook.stl. The 10x10 bin bracket takes 2…
Popis Box with handle - outer max dimension 108x125x54mm - inner max dimension 100x100x50mm Video with disassembly: Used screws: no screws needed 3D printing settings Layer 0,1mm for no supports (0,2 with supports - use organic tree 25°)…
Cutlery box outer dimensions 210x100x50mm inner dimensions 205x95x48mm Print settings 0,2 layer 4 walls 15% infill no supports
I exported a "strait" option that allows mounting the ventilation duct in line with the fan if you need that. The “side” version is the one I used to extract air from a cabinet as shown on the pictures. The cabinet is used a cat litter…
This is parts for 110x55mm rectangle ventilation ducts. Orientation for print will depend on printer and you may have to experiment with support. Here is an example of a duct angled 45 degrees for better print and result with overhangs.…
This is a magnet case that keeps the magnet in place without the need for glue. Print two parts as separate objects.
Meeting my local store I was shocked by how expensive those parts are (reg. EUROPLAST System 110x55) and made some parts myself. Model is for 0.8mm Nozz and NO Supports (whilst therefore, my design is a little different compared to the…
Meeting my local store I was shocked by how expensive those parts are (reg. EUROPLAST System 110x55) and made some parts myself. Model is for 0.8mm Nozz and NO Supports (whilst therefore, my design is a little different compared to the…
18650 10x5 holder. Simply large holder to 18650 cell li-ion
This is bed slad holder (maximal slat dimension 10 x 53 mm, pitch 34mm).
Coiltek nox 10x5 coil stiffener for minelab equinox
90° elbow fitting for 110x55mm rectangular ventilation duct Vertical/horizontal orientation Male / Male Print recommandation : Recommended PETG Layer Height 0.28mm Infill 15% ---------------------------------------- Pièce d'angle 90° pour…
When modding Dell Optiplex 7020, there is not enough clearance to "bend" PCIE cables with larger GPUs. This mod provides 10mm extra clearance and little extra ventilation for fitting larger GPUs into an Optiplex. Comes with two parts, the…
Simple magnetic mount for a 120mm case fan. Adjusted from the original to fit some 10x5 magnets I had lying around and use an M3 insert, since M5 bolts are too big for most computer case fans. First time remixing something in CAD, so it…
Ventilation tube 110x55mm straight. To be printed standiing up. Scale slicer i Z-axis to get the length you need or want. In addition to the tube is a female/female part you can combine with the male-male tube of the 110x55mm ventilation…
I saw Keina's PCB Holder model and wanted to print one for myself hoping the magnets i had at hand would fit. Rather than take any chances i remixed it to use 10x5x2mm magnets. THIS IS JUST THE BASE ONLY! Youll have to go to Keina's page…
Customized version of http://www.thingiverse.com/thing:386904
You need a 10mm diameter x 5mm thick magnet. It presses in but I would suggest a bit of glue. Gluegun would do the trick. The thicker 4mm straw works for airduster and the thinner straw works for KEBCO Drilling & Tapping lube. You could…
Created small button to hold magnet inside for easier handling. Used adhesive to hold magnet inisde printed button.
I could not find a premade insert anywhere so I thought I would post mine to save you time if you don't know how to make your own insert. I made the insert from the original model's default fill. Printed at .2 layer height at 15% infill.…
By downloading 3MF file you should be able to modify magnet dimensions. Hole is there even though it's not visible on preview because of incorrect rendering of negative volume modifier.
Attachment of square plastic pipe (air conditioning) to the wall or ceiling
cover cap for flat duct 110x55mm (e.g. intelmann) for sleeve (113x60mm) petg → 250 celsius → 0.12mm layer
Hmoždinka 10x50 tištěno s límcem… Límec neodlamovat , ale složit ke hmoždince jako výplň a proti protočení. Díru vrtat co nejpřesnějí 10mm.
