Counting matching models…
This is a modular system with which many kinematic chains, aka robot arms, can be constructed. The modules can be seen in image 1. The chosen actuators are very cheap servo motors without gearbox, which brings advantages and disadvantages…
3D printed robotic arm with a video tutorial on youtube. I’ve developed a 6 axis robotic arm that can lift up to 150g with an amazing precision of 0.2mm thanks to stepper motors. This arms is my first project to develop a solution for…
ErgonoMouse is a do-it-yourself 6DOF Controller (6 Degrees Of Freedom) based on Arduino. Or commonly known as "space mouse". It uses commonly available hardware (see “Required Hardware” 🡣) and it requires intermediate printing,…
Support de charge pour montre connectée Nerunsa P66D Charging stand for Nerunsa P66D Smart Watch Impression à plat sans support.
Print any filament, 0.5 width and mount nvr. Cover2 for mount rtl8812au 150mw reciever. Drill holes for ant where you need.
I'm changing DMF and clutch on BMW 116d. Changing DMF and clutch requires clutch aligning tool so the clutch end up in the center of the flywheel when mounting. Since this will be one time use and not a complicated geometry I made one…
Hawk 6DOF Hall Effect Joystick – Precision Flight & Space Sim Controller Overview The Hawk 6DOF Hall Effect Joystick is a high-precision, fully customizable flight and space simulation controller designed for immersive and responsive…
This is a Replacement DVD Drive Top Cover with the cut file for plexiglass. All of the print settings are in the Read Me file within the download! FITMENT: Lite-on DG16D4S, Lite-on DG16D5S ONLY. INSTALLATION: 1st: Print it and remove all…
A tip and nozzle holder for Yihua 8786D Soldering Station with mounting holes for adding accessories. The holes are for 4mm screws and are on 10mm centers. It holds 10 tips and 4 nozzles.
I designed this case that's inspired by visual futurist artist like Syd Mead and John Eaves. Not your typical boxy type case for a piece of audiophile equipment. This is meant to make it standalone and have a visual impact with futuristic…
6dof Stewart Platform Check out the new V2 design: https://www.prusaprinters.org/prints/17153-6dof-stewart-platform-v2 Print instructions Print Quantities: 6x - Shafts.zip.amf 6x - U-Joints V3.zip.amf 2x - Frame V2.zip.amf NOTE!!! Under…
Small remix for V6DM Heatsink from Trianglelab (https://aliexpress.com/item/1005005195556343.html)
6dof Stewart Platform V2 Print instructions Print Quantities: 6x - U-Joint.zip.amf 6x - Actuator.zip.amf 1x - Upper Frame.zip.amf 1x - Lower Frame.zip.amf NOTE!!! Under no circumstance should you use pre-generated .gcode files, it is…
156DT Display Tree This is the library for parts for the 15.6mm Display Tower. This is a modular tower that you build to fit your needs. Optimized for .4mm nozzle .2mm layer where possible. Most parts are printed with no supports The…
Designed to attach to the underside of a desk, for TP-Link TL-SG1016D 16 Port Switch. Print two pieces Unter Schreibtisch Halterung für einen TP-Link TL-SG1016D 16 Port Switch. Zwei Stück drucken
WIP model of my NVR Case for use with OpenIPC FPV and Ground Stations. This case is a remix of W's case that he posted on the OpenIPC Telegram page. Thx for getting me started. This case features the following: 50x50x10mm 12v fan slot,…
Simple solution for using the Bosch 18V batteries as a power input source for M6D charger. For attaching the Bosch battery is used this model > Adapter with fuse >…
You have to bend the thing in half to sick it in there, what are you gonna do? It fits nice and snugly, so much that I didn't even need to line up the M3 screw holes. pokemon font!!!! you'll probably want to attach a fan somehow if you…
this is a casing vor the TPA3116D2 (AOSHIKE 8-25V 100W TPA3116 NE5532) amplifier. this is a lowpass mono amplifier for subwoofers. More information: https://www.youtube.com/watch?v=SO96JDnXoRg (not my video) where i bought the product…
This is an adapter that converts a DELL monitor stand into a VESA stand. Compatible with stands labeled “FFT-ZS”. Please let me know if you can use this model other than those listed below. UP2516D UP2716D U2717D Print setting Layer…
Shows good fit on the carburettor but should be regarded as a prototype.
This is a case for the Commander X16 Development board V2. Key features: Front Panel with Power and Reset Buttons, and indicators for Power and Activity. Support for Low Profile Expansion Cards Support for side Cartridge Support for a 25…
simple case for cheap TPA3116D2 2x120W class D amp board
Fixed the 16 degrees slider by removing part of it so that it fits around the plastic of a KING KW65 1000/6000 Whetstone
A few small accessories for the Yihua 2-1 in soldering/hot air station (might work on others, seems like the soldering handle stand is shared with others). angled soldering tip holder vertical soldering tip holder Both can be mounted on…
Case for Raspberry Pi 5 for adding two INNO MAKER MIPI 7251 RAW Cameras Edit: been having issues getting the 7251 to run so will be trying the OV9281 instead which should have better support. and a Adafruit 9-DOF Absolute Orientation IMU…
Here is the F-16D kit card. This is a simple 2 piece kit card, of the 2 seater variant of the F-16. This is my first model and kit card I have uploaded onto Printables. More to come in the future! Results in different printers may vary.…
**The Vtr_pcb files are only to mount support don't print them*** This is the evolution of the first Desk. I use a nozzle of 0.4 on my Neptune4, pay attenction to have the right extrusion to respect the tollerance. wood panels: 1 (central…
26mm Phaetus Dragon Heat Sink specification compatible with v6 volcano heat block for Stealthburner
Enclosure for chiniese bought subwoofer amplifier, I have designed it to be glued together, once put together, box have no openings for wires or any type of plugs, as that can be drilled if anyone have specific needs as per that.…
Features Removable power bank tray The power bank tray slides in and out easily, and is secured with clips. Accessing your 18650 batteries is very fast. Furthermore, the 18650 holder is an off-the-shelf part requiring minimal soldering…
Dies ist ein Auffangbehälter mit Extrafach für die Overlock Nähmaschine N 656D aus dem Hause W6 Wertarbeit. This is a collecting container with an extra compartment for the overlock sewing machine N 656D from W6 Wertarbeit. Print Settings…
Let me introduce this Mini Project. It‘s basically a case for a small DI Box. there are active and passive dI Boxes avaiable. Both will fit in the case We are using M3 Screws and we are using the CNC Kitchen threaded insert M3. But there…
updated to V2 to add additional clearance for audio jacks which were deeper than I guessed. I took jbebels remix of the Customizable Box and added the ability to have a second PCB. I also added in soe extra ventilation to the top panel. I…
Summary Here's a family of organizer tubes that fit perfectly inside a common Berry Kerr VL-16 16 dram pill bottle commonly found from your pharmacy. I also have a design uploaded for the smaller 13 dram version. Pill bottles are already…
Stand created to display the M6D magnum found here https://www.thingiverse.com/thing:2379783
I needed a low profile mount to stick to my wall as a baby monitor. I used two XL 3M command strips (removable velcro tape) to adhere to the wall. I printed the mount out of some PLA+ at 5% infill and 80% infill around the little arm…
Another nozzle organizer for the Atten ST-826D. The hole diameter is 30 mm. An infill of 20 percent is completely sufficient.
So my bench is a watchmaker's bench and my workshop is a 1-car garage, which means stuff needs to be portable. I needed a rework station and they all pretty much assume they own your workspace and maybe elsewhere? But not around here they…
DEMO https://imgur.com/BeThDN8 NEW VERSION https://imgur.com/a/GOBVW61 https://makerworld.com/zh/models/1297418-joystick-6dof-spacemouse DIY SPACEMOUSE 2 Joystick 6Dof MOD use waveshare rp2040-zero & 2 joystick module original author…
Simple case for a cheap TPA3116DA mono 150w class D amplifier board
Introduction Provides a cable box at the bottom of a Sonoff TH/POW 16/20A smart relay to safely enclose cable connections when used outside of a distribution box, such as wall mounting it independently. Without the cable box, mains…
5-6GHz 16dBi horn antenna. Just need to trim the driving wire to the desired range using a VNA (like the LiteVNA/NanoVNA). Apply tape VERY WELL and across the areas where the screws are (see photos for examples). The smoother the tape and…
Guide hop style retro mod for VFC HK416D & M27 generations 1 & 2. Official VFC system is patent pending, this is just a retro fit upgrade mod to bring your old HK416s back to life. No profit is being made of the mod. See manual in the…
Welcome to the Developers library for the 3UDC clip system and the 156DTmm display tree. Both of these systems involves lots of components and I wanted to put parts and information needed to create things in a non-end user library. These…
Both models were made with slots to insert magnets for a easier deployment, making it also possible to retrieve the magnets if the print doesn't turn out so well. The size of the inserted magnets is 20 * 10 * 3 mm and they can be found in…
This is a Bulkhead shim for a Team Associated B6 / B6D. It goes between the chassis & bulkhead, you can choose between 0.5mm & 1mm. It provides a smoother steering response and increases mid-corner steering. Some may find 1mm to…
I designed an extra piece to mount our AngelCare AC315 baby monitor on the "Modular Mounting System Arms - Customizable" by 6d6178 (printables model 185322)
I do this for my personal postation! I use it with cars simulator for indicate the gear! I have inclinate it about 6° for a better view It's for a single max7219+matrix dispaly all in one The rectangular hole in the top it's for cablage…
Gleisrost für eine asymetrische Doppelweiche, Schienenform 6d der KPEV. Schienen müssen mittels Schienenfüßchen aufgenagelt werden. Bohrungen für Weinert-Schienfüßchen und Peko Code 75 Schienen sind bereits im durchgegehenden Gleis…
XH-M543 (TPA3116D2) case for mounting under desk. Power through XT30-M connector You can use 2 inserts m3 with 4mm length, or just melt 2 plastic pins I used a minijack 3.5 mm female this type:
Caja para amplificador XH-M422 basado en el chip TPA3116D2. Permite conexión por bluetooth, puerto microSD y USB. Como se ve en la foto, he usado dos viejos altavoces creative que tenía guardados por casa. Material necesario: circuito…
Needed a stand for the ethernet switch that connects our Ultimaker S3 printers to the computers we use for slicing. Support my work: PayPal Donation: https://www.paypal.me/disizitstudios Cults 3D:…
the mounting points on the back's cross section are too thin and when combine with the printing direction(layer lines), it's too thin for printing wih ASA easily broken off. I just make it thicker.
.2 layer height 20% infill.
Suport for multimeter HABOTEST HD206D with magnet and M3 version.
Enclosure for my audio power amplifier based around the Tpa3116d2. You can find pcb details and download here: http://www.maj.pavlin.si/ Category: Audio
Very simple, but useful holder for Habotest HT206D. Fit perfect with Habotest HT206D and M3 insert HSW Printed without supports
Keychain inspired by iconic Nissan RB26DETT engine (head gasket) Print settings: Layer height 0.2mm, 100% infill, nozzle 0.4, ironing on Dimensions: 80mm length, 3mm thickness
All my designs & progress available @ http://marginallyclever.com . I can make one for you if you want. Video: http://www.youtube.com/watch?v=rhuM6Cnn5Pk Some times creation is all about low hanging fruit. I already have a Rotary Stewart…
The design secures the drive using four M3 screws (standard internal mounting points) and attaches to the underside of your desk with two wood screws. Ideal for custom PC setups or media stations where internal drive bays are unavailable.…
This item can support your HK416D. Please don't let your beloved weapon lie somewhere, let it stand up and show it to your friends. Since private ownership of guns is not allowed in our country's laws, this is the parameter of 3D printing…
[EN] Dead man's security repair kit for Grillo G126D tractor. This part could be fitted on other old tractors from this brand. Printing tips: 30% infill (cubic), 3 perimeters, 3 layers top and bottom, supports like the photo [FR] Kit de…
I wasn't a fan of the "stuck down" container for the tip cleaner so I did my own even had some filament in a strangely good color match, I have added the location if you feel the need to screw it down from under neath but its a tight fit…
Ford Fiesta MK-2 "Fiesta CL 1.6D"
This device was developed to be attached with double side tape to the machine. For additional protection, a board cover was made to fit in the ESP32-S3 support and allow the connection with the battery and the external sensor. The code…
Just a very simple space. that lifts the Pyle PLPW6D up enough to make it fit in the space available on the BMW Z3 subwoofer box. The screw hole amounts are spaced to match the Pyle subwoofer and you can drive screws into the subwoofer…
The holder can be printed from any material. No supports are necessary when the model is placed on the build plate with the foot facing down. A layer height of approx. 0.15mm is recommended. By using threaded inerts for M3, it is possible…
Replacement Antiroll/Sway Bar for the Team Associated B6/B6D. It's only the bit that sits on the back of rear gearbox but can be easily damaged/broken. Its not the most cosmetically pleasing model but its functional. Best printed in ABS…
Xytronic Fume Extractor 426DLX Grille replacement. Fusion 360 file included.
A compact holder for the Yihua 8786D soldering station. Stores 3 hot air gun nozzles on the side and mounts with two M4×6 screws. 🖨 Print time: ~31 min ⚖ Filament: ~11 g ⚙ Settings: 0.2 mm layer height, 3 walls, 20% infill Setting Value…
Organize your RC workbench with this compact Skadis mount for the ToolkitRC M6D Dual Smart Charger . While the original design was great for all-in-one portability, many workshop setups use a dedicated power supply tucked away elsewhere.…
This design is available under CC BY-NC-SA 4.0 for non-commercial use. The board is this one. You can also find it in many other places.…
This holder mounts to two of the standoffs in the front part of the mower. The standoffs are drilled and M3 heat set inserts (I used BOSSARD 1386743) are pressed in. M3 screws are then used to secure the holder. The PCB to the left of the…
Holder of 11 tips for the Solomon SL-916D soldering and desoldering station. I printed it from PETG with standard settings. No supports needed. Soldering tip hole diameter: 6mm Desoldering tip hole diameter: 7.5mm Object size: 120 x 40 x…
Additional materials needed: USB PD trigger board - aliexpress.com/item/1005009301680543.html Female XT60 connector Wire Hot glue for gluing the lid Reccomended to print the lid with fuzzy skin enabled to improve grip.
|'ve designed a lockable joint for 8mm tubes. It has serrations that locks every 6 deg. It uses a M8 bolt as an axis. The tubes can be secured in the joint by 3mm screws. I've added a drilling jig to make the holes in the tube ends.
This is a 6DOF Robotic Arm. NOTE: This is not an electronic arm, neither is it suited to be automated. It is merely a helping hand/holder. It WILL NOT hold by itself, you will have to either glue the parts or put some kind of putty in to…
This over-ear headphone extender. It serves to reduce the discomfort caused by movement touching the ear, causing it to heat up. I used the 20% fill setting and the adapter must be glued onto the part. mounting the pad on the adapter.
Hackclub x rx76d Keychain A keychain with a Macintosh on one side and the Hacklub logo with my username on the other side. Printing & Assembly Resolution: Print at 0.12mm layer height so the small "hack" text and rainbow stripes remain…
10" rack mounting trays for the D-Link DGS-1016D (model without fan) gigabit switch (witch is 11" in original case). This is made for my rack with rails on both front and back side and are made to only occupy 1U space. The mainboard…
Its a Remix from EatMoreTronxy , the left cover has the wrong size... this should be fit. Category: 3D Printing
A slime VR case for a LSM6DSV + 18650 battery, handwire and a rocker switch like a PSU one
Housing for the 100W Bluetooth 5.1 TPA3116D2 Mono Bt Audio Power Amplifier (link at bottom). The design is pretty simplistic, the amp slides in from behind. The two holes are for the volume knob and the AUX port. The openings in the back…
Redukce na vysavač pro přímočarou pilu Narex EPK16D
Hackclub x rx76d Keychain A keychain with a Macintosh on one side and the Hacklub logo with my username on the other side. Build Instructions: Software: Download OpenSCAD. Paste the code, Render (F6) to generate the mesh, and Export as…
I printed the hopper in PLA and PETG, both are working fine. The lid is PLA. For the hopper I put the seam to the back and used a brim. Otherwise nothing special, 0,4mm nozzle, 0,2mm layer.
Print it facing down so it needs no supports. I recommend 20 percent infill with gyroid, i printed it at 0.25mm layer height/structural with the generic petg profile, zoffset of 0.034 and the bed to 90c The switch: TP-LINK TL-SF1016D The…
The Nano Motion Rig is a compact desktop motion simulator platform that demonstrates up to six axes of movement in a minimal footprint. All structural components are 3D printed in PLA and assembled using standard hardware. Designed for…
EN - This Di2 junction box cover is designed to integrate cleanly into the Vision Metron 6D handlebar. The goal is simple: a cleaner cockpit look while protecting the junction box. It’s designed to be easy to install and straightforward…
This is a hard case designed to fit inside the bag for Radio Link's radio-controlled transmitters.
Concept CAD collection for a DN100 PN40 trunnion-mounted ball valve with an ISO 5211 actuator interface. Includes the full assembly, cutaway, valve internals, and sphere/stem unit. STEP files are provided for CAD review and educational…
Gridfinity-compatible holder designed for the ToolkitRC M6D dual smart charger . Keeps the charger, cables, and small accessories organized in a compact layout. Available versions: 2×3.5 – Charger with large cable compartment (allows…
Hackclub x rx76d Keychain A keychain with a Macintosh on one side and the Hacklub logo with my username on the other side. Printing & Assembly Resolution: Print at 0.12mm layer height so the small "hack" text and rainbow stripes remain…
Just a very simple space. that lifts the Pyle PLPW6D up enough to make it fit in the space available on the BMW Z3 subwoofer box. The screw hole amounts are spaced to match the Pyle subwoofer and you can drive screws into the subwoofer…
Print it facing down so it needs no supports. I recommend 20 percent infill with gyroid, i printed it at 0.25mm layer height/structural with the generic petg profile, zoffset of 0.034 and the bed to 90c The switch: TP-LINK TL-SF1016D The…
The holder can be printed from any material. No supports are necessary when the model is placed on the build plate with the foot facing down. A layer height of approx. 0.15mm is recommended. By using threaded inerts for M3, it is possible…
This is a hard case designed to fit inside the bag for Radio Link's radio-controlled transmitters.
![ErgonoMouse [Free version] - 6DOF Controller Knob & Joystick with Wheel, Buttons & Keys](https://media.printables.com/media/prints/973725/images/7443301_6431622c-6203-4049-abb5-c021b4241c1f_e177f1da-39c9-4328-8e49-8818ce495155/promo-knob-free.png)
![Dead man's security [Grillo G126D tractor]](https://media.printables.com/media/prints/63286/images/659756_0b2d3892-2bcb-44b5-9f7b-5df576904986/securite_homme_mort_img4.jpg)
