Counting matching models…
This is a Mount to place the Leo Bodnar 10MHz reference mini GPS module on the side of the ICOM IC-9700 radio. This uses 2x M4x8mm screws (MAX 8mm, or you will damage the radio) I printed this side on, with supports on build plate only,…
This is a protective cover for the front of an Icom IC9700 or an Icom IC7300 Amateur Radio Transceiver. The front face plates of both of these Icom radios are identical and so for those of us lucky enought to own both, two print runs will…
Mounts a RAK19007 into the QILIPSU Junction Box 5.9"x3.9"x3.5" RAK4631 - $25: https://store.rokland.com/products/rak-wireless-rak4631-nordic-nrf52840-ble-core-module-for-lorawan-with-lora-sx1262 RAK19007 - $18:…
Connect your headset to your TRX. All connections fit into this small box. The box fits nicely on the side of the TRX. Holes are 6mm and 8mm offset. Holes for magnets are 10 to 1mm. If you have any questions you are welcome to write. Vy…
Epson Stylus Pro 9700, while relatively cheaply available from ebay and other sources, do not have a lot of replacement parts available from Epson anymore. While the InkTube Assembly is still available from Epson, it costs an arm and a…
Introduction Dell XPS 9700 tends to get hot when gaming, wanted some easy to carry feet to improve air circulation when needed. This part elevates the back of the laptop by ~20° I am proud of this simple piece and would appreciate your…
Bližší informace o modelu na stránkách Lega nebo v aplikaci LEGO Builder. Zkompletováno z různých zdrojů na internetu, popřípadě navrženo ve FreeCadu.
I dropped my original metabo 626697000 bit box. The lid crashed and the box itself cracked, so I needed a replacement. And thanks to the FANTASTIC paramatric rougged box (v2) here we go :) Warning: I am not skilled in 3d design. I just…
This is a modified version of the „Radiator Grille External To Headlamp Nut“ from General Motors, part number #3999700. The part is discontinued and no longer available. I needed replacements for the brittle original ones of my 1982…
Replacement plastic parts for the Ink Holder Right of an Epson Stylus Pro 9700. Epson no longer provides this part for the printer and I broke mine while trying to clean out a clogged nozzle, turns out the "cleaning" fluid actually…
A small snap fit box for the PTRX-9700 reference injection board to sit inside. Tight fit so print the base first then alter the size of both parts if necessary. Printed at 0.12 layer height.
The old Life Fitness treadmills models like the 9100, 9100HR and similar like the 9500 lack the possibility to conveniently hold your phone or tablet. Here are my 2 solutions for the matter. One clip that goes around the display and one…
A case for a USB to RJ45 Ethernet adapter, based on a SR9700 chip, where original case was broken and lost. It consists of two parts, which snap together, but it would be wise to some tape or glue, to make them stay together. I printed…
This is a single-piece AM4 mounting adapter for the Zalman CNPS 9000 / 9005 cooler. It is designed to let these older Zalman coolers be mounted on AMD AM4 motherboards while keeping a mounting method that is close to the original one. The…
Portable Charger for the Baofeng BF-9700 radio. Designed specifically to house the IP2326 USB-C charging module. Print Settings Supports: Yes Material: PETG (recommended for snap-fit flexibility) Hardware Required 1x IP2326 USB-C charging…
Stacking bracket for ICOM IC-7300/IC-9700 transceivers. Wanted to be able to use the tilt foot on the lower radio and a little more space between the units. This bracket (x4) provides the necessary stability and additional air gap. Note…
Simple bracket to keep a Dell XPS on a folding desk when it is folded down while still keeping it accessible. I wanted to avoid drilling through the surface of the desk to make a more permanent bracket. This is a very niche item but I've…
In case your radio doesn't have any feet / stand like mine does, these offer a 10 degree tilt for your radio. Use an M4 x 16mm style bolt to attach to your radio. duplicate and mirror this model to print legs for the other side of the…
Simple bracket to keep a Dell XPS on a folding desk when it is folded down while still keeping it accessible. I wanted to avoid drilling through the surface of the desk to make a more permanent bracket. This is a very niche item but I've…
