Counting matching models…
Instinct MI50 BBQ blower fan shroud JSCAD share link There is a new sticky “Radeon Instinct MI50” thread on mersenneforum.org (registering needed for access): https://www.mersenneforum.org/node/1072920 Used Radeon [pro] vii GPU prices are…
Printed vertically with the fan side facing down, with supports to support the part that mounts the shroud to the card. M3x10 screws used. First plug in the EPS to 2x PCIE cable then mount the shroud and screw it in using the 2 screws and…
Made a nice organic looking air intake to cool four Nvidia CMP 170HX PCIe cards with two high pressure 120mm fans. They move more air than 8x 40mm fans and are hell of a lot quieter. Also compatible with the A100 PCIe and potentially…
120mm fan duct for NVIDIA A100 / CHMP 170HX GPUs. It's not a very efficient design, but it's enough to cool a CMP 170HX with a 120mm Noctua industrial 3000RPM fan. .STL file is included Printing: Orientation: Large Flange on bed Material:…
Sigma Aura 100 gopro Halterung /Sigma Aura 100 Gorpo mount
I needed a model to hang my Elitedesk on the wall but didn't want to attach it permanently since i'm going to mount it in a tight closet. This way i can just slide it out if i ever need to plug something in. The standoffs need to be cut…
This 2.5" HDD enclosure is designed for the new generation of 15mm Seagate 4 and 5TB hard drives. These hard drives are cheap, whisper-quiet, very economical in power consumption and can therefore be supplied with power directly via…
TrackIR arm that mounts under the VESA100 screws. The sensor mounts magnetically to the arm like the original stand. There are short and long arm pieces to customize the arm length. Additional hardware requirements: -M5x30 bolts and nuts…
I printed Gomiappuroda's blower adapter (https://www.thingiverse.com/thing:6773548), with the end chopped off when slicing to save space, then used this piece to mount the blower next to the card so it fits in my case. Two versions, one…
This is a custom blower cooler design for the Nvidia CMP 170HX that replaces the original shroud. It is approximately 305mm long. It has satisfactory cooling performance, while having a more traditional integrated form factor compared to…
This is a minimal wallmount for monitors with a vesa100-compatible mounting plate. It works like a frech cleat but with no chance for the monitor to slide sideways of the mount. I have a 24" benq monitor attached to the mount an it is…
Got a small desk where your monitor takes up half the space? Mount it to the wall! This is a removable Monitor mount for your wall. There's no adjustment (yet) so you'll have to measure it right! I wanted the design to be removable so I…
A VESA100 mount for this awesome model - https://www.printables.com/model/309029-modular-75mm-vesa-monitor-arm/remixes#preview.yxqLb
VESA 100 mount for a Netgear R7000 router. Enables mounting router on back of LCD Monitor. Saves desk space. I swapped out the router middle antennae with an remote/extension wired antennae, so the middle antennae wasn't in the way of the…
I recommend printing from ABS or ASA. PETG used in the photo. 0.20mm layer, no supports.
I made a set of replacement pieces for the LaserActive, but as they are all quite small detailed parts (and not to mention, awkward angles for FDM printing), it either requires a Resin printer, or you could order them through a shop like…
A grip, tripod plate, and bottom right strap connector for the Nikon Coolpix A1000. Pictured here in Prusament PETG galaxy black. I recommend adding some fuzzy skin with a box modifier to make it feel nicer! The problem The Coolpix A1000…
Replacement for the usually gooey or brittle 42mm plug used to seal 42mm holes in the wiper compartment of W639 Viano and Vito. Might fit other Mercedes Benz models BEWARE, this is made to print in TPU/Flex. Using any other non flexible…
I made a set of replacement pieces for the LaserActive, but as they are all quite small detailed parts (and not to mention, awkward angles for FDM printing), it either requires a Resin printer, or you could order them through a shop like…
Using mitikohalls original design(https://www.thingiverse.com/thing:3245793), I've been able to make a sturdy case for the Nordic Semiconductor nRF52840 pca10056 development kit. The case has a dedicated reset button and exposes most pins…
I made a set of replacement pieces for the LaserActive, but as they are all quite small detailed parts (and not to mention, awkward angles for FDM printing), it either requires a Resin printer, or you could order them through a shop like…
I made a set of replacement pieces for the LaserActive, but as they are all quite small detailed parts (and not to mention, awkward angles for FDM printing), it either requires a Resin printer, or you could order them through a shop like…
This is a ground up rebuild of a battery holder for the new generation of Sony cameras. It is completely parametric, having been put together in Rhino 3D and Grasshopper.
I made a set of replacement pieces for the LaserActive, but as they are all quite small detailed parts (and not to mention, awkward angles for FDM printing), it either requires a Resin printer, or you could order them through a shop like…
Have a 3 monitor desk stand, but with HMD, I don't need all 3. So now one of my VESA Brackets can be a convenient place to store the HMD when not on my head. M4 nut sockets, ideal with 12mm M4 screws. Print instructions Category: Tool…
This is a VESA mount for the Siglent SVA1000X / SSA3000X series of spectrum analyzers. I have tested it to fit my SVA1032X (same as the SSA3021X / SSA3032X). It grabs the instrument by the vent holes on the back, and provides bracing…
This thing was made to adapt a E-body flip top gas cap to my Dodge A108 Van. 10-32 Nuts are instated into the adapter then bolt the adapter to the filler neck after the adapter is secured to the Filler neck bolt the gas cap on. I used…
- detail description an photos would be added later
Its an adapter to Mount an Vesa 100X200 (some TV's) display on an Vesa 100X100 monitor arm. The adapter has been holding up the 32" tv I'm using as a second display for over a year without a problem. I printed it out of petg with lots of…
This little customizable angled case perfectly fits the Eachine TX03 AIO camera. You may have to slightly change some parameters in the OpenSCAD file to match your printer tolerances. The cut on the back-right-side is for the video-in and…
This thing is a Front Marker Lens for a Dodge A100 Truck or Van or A108 Van. This is an elusive part if you are searching for it at swap meets. In the past year or two reproductions have been showing up on eBay but they sell for about $70…
Simple feet to absorb some vibrations for the Dayton Audio HTA100BT tube amp. make with TPU.
The images show it mounted into a piece of carboard…. but it will get mounted into a piece of wood as soon as I get further along on this record cabinet restore… This can be printed with no supports as is (face down). If instead you want…
For a smooth finish on the logo and a rough finish on the deboss, print with the logo facing down. It shouldn't be necessary to adjust the horizontal expansion, although I recommend printing the test piece first.
I found this cassette recorder in a local trash :-) It suffered from the rain and dirt, but the average condition was 4+ star, so I decided that it could be still alive. I took it to home and disassembled it. The antenna was broken - only…
Designed this a few years back. I intended to print it with my SLA printer in clear but couldn't get the clarity right. I could only achieve driver quality with A LOT of post processing. Maybe you could have better luck! The seal is good…
There's a new version! See https://www.printables.com/model/597188-nikon-coolpix-a1000-grip-and-arca-tripod-plate-upd This is the first one of these custom compact arca-type tripod plates I designed, and it's a bit cursed, but there's a…
Vesa100 support made for an HP T630 Printed in PETG with 3 wall, 4 top and bottom layers, 20% triangles infill. Tree supports were used.
This Sigma Aura 100 Mount has been created from scratch. But as inspiration the Model from @TEDesign was used. My model also uses the same mounting arms as the Model below. So please download those from the Model below to credit the…
Print upside down and supports may be needed for version 2….210mm x 210mm x 152mm
This bracket is designed to mount a hi-fi amplifier under a table. Without gaps Can be placed on any surface. Mounting holes - 5mm. PETG plastic Perimeters - 3 filling - 15% layer - 0.2 Use supports.
Modified version of ed_33519's Intel NUC Adapter. Added cutouts for 4mm nut and extended to 4mm. This allows you to attach vesa100 compatible items to the back of the Ergotron HX Dual Monitor Arm Bow Printed in PLA, 20% infill, with…
Vesa100 support made for an HP T630 Printed in PETG with 3 wall, 4 top and bottom layers, 20% triangles infill. Tree supports were used.
Modified version of ed_33519's Intel NUC Adapter. Added cutouts for 4mm nut and extended to 4mm. This allows you to attach vesa100 compatible items to the back of the Ergotron HX Dual Monitor Arm Bow Printed in PLA, 20% infill, with…
I made a set of replacement pieces for the LaserActive, but as they are all quite small detailed parts (and not to mention, awkward angles for FDM printing), it either requires a Resin printer, or you could order them through a shop like…
January 7, 2024: Added some more performance data to the bottom of the original blog post on what happens with key down.. https://holdmybeer.io/2023/12/22/ham-stack-fan-shroud-for-elecraft-kxpa100/ January 4, 2024: I recorded a timelapse…
Printed in ASA for strength fill needs to be 45% or higher. The screws for the side of the amp are 10-32 x ½ long. Tighten the thumb screw on both the radio and panadapter prior to putting on brackets. the same brackets fit both.
![Nikon Coolpix A1000 Grip and Arca Tripod Plate [UPDATED]](https://media.printables.com/media/prints/597188/images/4755255_1800b8d0-6da9-492b-9b17-c8c8b96d3b82_8fe4b957-24f8-472a-a3b7-e527240c87d3/dscf2501.jpg)
![W639 - 42mm plug - A1009870044 [Scheibe] - Vito / Viano Mercedes Benz](https://media.printables.com/media/prints/9efeb331-90d2-427e-98a7-7c6ae16ee987/images/9725173_94da1573-0068-43e2-a5ca-d3a95fc459fe_2315b8ff-fb92-4834-8458-d30913b8157e/img_5162.jpg)
