28 models
We were updating our church to in ear monitors , but didn't have a digital board to have an aux for each person, and I came up with this idea. Use the Behringer MA400 as a partial personal mix for instruments. Then the Mackie HM-4 for the…
Print approx. €4.40–€5.38 excl. taxPreliminary estimate for one variant
Needed a way to mount the Behringer MA400 (and its knockoffs) near orchestra members either on a mic stand or the music stand without needing extra stands. Supports are only needed for the bolted mount inside the hex area. Hardware…
Print approx. €2.03–€2.48 excl. taxPreliminary estimate for PETGSource material: PET
use PETG 0.3mm m12 Nut *4 m12*20 Screw *4
Print approx. €4.72–€5.77 excl. taxPreliminary estimate for PETGSource material: PET
Passionate about aeronautics, I wanted to modelize this aircraft. Designed in several parts, this model can be printed without difficulty and with reduced supports. The canopy being designed separately from the main model, it will be easy…
The bottom recess will fit a single 8x3mm magnet. I'd recommend printing with PETG if possible (less brittle). The original model was designed for assembly as opposed to print-in-place. Printing the parts separately will likely yield…
Old computers are great, but the plastics don't stand the test of time, yellowing through brominated flame retardants, or just getting brittle with age. The Amiga 4000 is one of those affected, and due to the limited numbers they were…
Custom completely printable SFF PC case able to fit Nvidia RTX A4000 (slightly modded). The goal was to design and develop the smallest possible PC with powerful workstation graphic card with four display outputs. Parts: MB: Asus ROG…
The Airbus A400M is a versatile military transport aircraft designed for a wide range of missions, including cargo transport, troop deployment, medical evacuation, and aerial refueling. Developed by Airbus Defence and Space, it combines…
A handy model where you can fix your Behringer Ha400 Microamp device under the table. The bolt holes are open. All you have to do is screw the bracket to your table. I recommend using support in printing. Designed with wide tolerances.…
A simple rail that attaches to the tube rings of an Askar FRA400 refractor telescope. The rail mounts to the rings using M6 screws. The center holes are designed for 1/4-20 or M6 screws and hex nuts (11.5mm between flats) whereas the…
This 3D-printed bolt-release shroud is designed to be installed beneath the bolt-release latch of first-generation Beretta 1301 Tactical, Beretta 1301 Competition, and Beretta A400 shotguns. Its purpose is to help prevent unintended…
Ring that holds the hood of an Askar FRA400 refractor telescope in the extended position. Requires a 10mm or longer M2 screw and hex nut. Without the screw, the ring is flexible enough to be passed over the hood.
Use this to mount your RTX A4000 GPU
Cable holder that mounts to the tube rings of an Askar FRA400 refractor telescope using M6 screws.
A two-piece swivel hanging mount for the Hako FA400 / FA-400 Fume Extractor / Smoke Absorber. Slots for zip ties and holes for screws. The mount comes apart so you can easily unhang the fume extractor and use it in a different location.…
Overview: This is a tray to hold a SD Card to SATA interface adapter in the lower floppy bay of an Amiga A4000. The SD Card to SATA adapter was purchased from Amazon, I used this device in the photo. You'll need nine screws and some glue…
Ozdoba na ścianę Airbus A400M MIlitary
Remixed from https://www.thingiverse.com/thing:5100822 but much stronger. I have a case missing many of the internal parts and found this one. When I first printed it, it worked but broken when attempting to use it with any cards. Its…
This is a 180 degree Rotation scale for the ASKAR FRA400 telescope, though it might (should?) work on any of the ASKAR scopes with a 78mm drawtube. Major divisions at 30 degree, minor at 5 degrees. Line up the centre division with your…
I've created this nema 11 stepper motor mount for my ASKAR FRA 400 telescope. I give as well my dew shield for this scope. You have to found the adapter piece (coupling) 2.5mm to 4mm (stepper to focuser) as I've not designed myself.
This is a simple hand-held mount that we designed in 2014 for a pair of Canon PowerShot A4000 cameras to capture synchronized stereo images or video. The camera mount is our own design, holding a pair of A4000 so that the stereo baseline…
Original one fit great, just need to add a bit more plastic to the bit that holds the card in. Category: Computer
I bought what I can only assume was a fake FA-400. Either way, it had a look only a mother could love (or a fanboy) and a sound that needed taming. First I installed silicone washers. This worked well, but I found the shape inconvenient…
I love fisheye lenses, both for artistic and technical purposes, and I have quite a collection from door peepholes to high-quality fisheye lenses. Unfortunately, few cheap options give full 180-degree views, and almost none give more than…
Use 10% infill with gyroid to print. I used TPU 92A and Prusa Mini+.
Plastová pohybová matice z pohonu křídlové brány Moovo XW432 , XW532, NiceHome ARIA200/ARIA400. Materiál: PETG Tryska: 0.4mm Výplň (infill): 100% Tištěno tryskou 0.4 mm, výškou vrstvy 0.16 mm, infill 100% na Bambulab A1, PETG se skelným…
I recently repaired a Technics SA-400 receiver and, in the process, converted the lighting to LEDs. Since suitable BA9S LED bulbs are quite expensive (at least in my country) and installation in the spring-loaded sockets is very fiddly, I…
