Counting matching models…
The files here maximize the usage of the print bed from the AnkerMake M5 (235 mm × 235 mm)) and M5C (220 mm × 220 mm) printers to print the honeycomb storage wall. New to the honeycomb storage wall? Look Honeycomb storage wall by RostaP ,…
Printing recommendations: FILAMENT TYPE TPU 85-A INFILL 25% WALLS 1 MM LAYERHEIGHT 0.20 MM Original designer: This is an articulated mouse. It can move its head and its tail. No assembly needed. It prints already assembled…
The original model was great but I found that I was having trouble getting the screws to grab the nuts so I made some tolerance adjustments to allow them to grab better. If you are having this issue, here is your solution. Simply replace…
I noticed after printing the original v2 model in PLA that the cards in the first few slots would not easily extend from the wallet, while the back cards came out too easily. To correct this, I changed the orientation of one corner so…
Insert for the game, it has been adjusted to fit perfectly giving no lift and not giving any room for things to slide.
Disclaimer: I have only tested this design once! I'm not sure how this print will perform at different sizes from what I used. The key print settings I used were: -125% size -PETG -Organic supports, manually placed -0.4mm nozzle -0.1mm…
Light bar for the AD5X adjusted to fit this LED strip: https://a.co/d/hUbBwfu . Requires you to carefully snap off one of the connectors at the end of the LED, and it helps if the material is warm, allowing for easy insertion of the LED…
I wanted to use the life counter by @Scottimus in a multiplayer Magic the Gathering game, but with the number indicator on an angle, it made it difficult for everyone around the table to see my health. This remix is only for the sides and…
This is a modified version extruder mount from Ender 3 S1 Cable Chain by TechRex. Things I modified: Patched up the holes in the model. Moved the chain mounting point so the chain can stay straight with the Y-axis Mount. Print Settings:…
I love this tally counter but the fit of the parts out of my printer was too tight for it to operate. I fiddled with my printer a bit, but figured I could use the practice so I traced the models in to Fusion 360 and adjusted the…
Just 999henry's can holder stretched a little in the Z axis so it will hold 500ml cans better.
My filament sensor was making a lot of noise and adjusting the lever screw did not solve it. When changing filament I started noticing that the filament did not move smoothly through the sensor at all. I opened it up to see if it needed…
Automatically adapting to different material dimensions. Square ranging from 10mm to 150mm, round from 10mm to 120mm.
I helped someone print these and due to the curved edges and the concerns about the strength of the clips I helped them by modifying this model to print in such a way, that the clips are really strong and where the curved top profile of…
I printed the original sock blocker for a friend but came to the conclusion that the tolerances were too tight for my printer. I, therefore, increased the tolerances a bit. Someone contacted me to share the adjusted file, so here it is! :)
There's been so much frustration getting my stupid HSW and accessories printed. You either have very tight tolerances, sometimes not even fitting, or you have to resize the inserts in the X and Y to 99%. But that means that other models…
This is a remix of the metric remix by @energeticinterpretation44 of the original model by @GarageTimeDavid_3790 All I did here is to enlarge the M6 holes slightly so that M6 bolts have proper clearance. All kudos to the original makers.
Parametric S1 / S1 Pro (sprite extruder) Dial indicator mount - can be adjusted easily to any printer I wanted a model that can be easily fitted to any printer , and any dial indicator so everything is prameric if you want to adjust it to…
This is a Prusa mini 3.2-inch display box, to apply the FYSETC Prusa mini 3.2-inch display. The display box from FYSETC was hiding a bit (1mm left and 1mm up) of my screen. To solve this, I moved the display 1mm up and 1mm to the left.…
On the cover you can see the first version. Drawing and model files for a refined version. See dimensions on a photo. Sizes can be slightly adjusted in Autodesk Fusion. Should work with Bambu AMS \ Lite. But I have no to test. Printed in…
I saw the remix of the base to a double base so I decided to print a second organizer. The first remix closes the holes of the original (v.3). The second remix changed the USB slots to USB-C slots and removes the SD card slots to a small…
This object has been designed in order to be simply printed and used for your dioramas or to create lots of realistic cement barriers using the mold by strain cement inside of it. The mold is made up of four parts: you have to join them…
I made some modifications to the Solder Scroll so it can accommodate small 5 mm x 11 mm x 5 mm bearings. https://www.amazon.de/dp/B092Q5M7FY To fit these bearings, I removed the inner shafts for the gears and the scroll at the back. I…
Works perfectly and fits perfectly on the hexes.
Basically a test print of an STL file, with a 3MF profile so this is a little easier to work with. If you have the latest flow control calibration (i.e. the latest firmware), your preview screen should look like the .PNG I shared here. Do…
Category: Toy & Game Accessories
I loved the idea behind this design but had to make the steak knives work with our shallow drawers. Printed in PETG but I'm sure PLA would be fine as well. Edit: Added a 1x2 Knife Block Extension, for those those with a little bit longer…
This is a remix of the gear-mounting bolt for the wonderful yarn winder model posted by BGDglider . The original model worked well for me with one exception: each screw that holds the drive and middle gears in place…
This remix is a pre-supported version for resin printing of the original model . Supports were created manually in Lychee slicer and successfully test-printed. Note The original model had parts of the spears coming out of the back, which…
I wanted to try out the “brew by weight” function on my espresso machine. However, with the scale placed on the drip tray, there wasn’t enough space for my coffee mugs. Since we enjoy both cappuccinos and Americanos, I designed an…
A remix of devonjones Dwarven Halls Knotwork Floors. The originals weren't playing nice with my other floors (too tall) so I chopped them up, removed some unneeded height, and affixed them to the 7.x series Triplex bases. The knotwork…
Big thanks to the https://www.printables.com/@landmaj_146897 for sharing the STEP file upon request! This is a remix of the DeLonghi Dedica drip tray designed to better fit certain models of the Dedica series. I adjusted the position and…
Allows to join two life counters together. Check the original model this remix is based on for more information, this one contains only the different files. Files to print (original, angeled version): Life_Counter_V1.00-middlepart.stl…
PETG, 5% infill, 2 layers. Maybe 200x200 will be fine with small mods. If you want so, let me know in the comments, I'll create smaller versions then. It's a simple work, but boring and took me quite some time, so you don't have to waste…
A small change to chrisbarratt's awesome angled screen mount to allow for a 2.8" discovery screen with a 5mm offset
When having both the optional “Hinged-Lid” and “Advanced Filtration System” add-on installed, you'll find you have to share 1 connection with both of them. I've adjusted the “Hinged Lid Hinge-Bracket-R” to accommodate “Advanced Filtration…
Print with supports. I used PETG. Just hang this like the original. Make sure the notch (which is not centered) aligns with the nozzle brush. OpenSCAD file provided for further tweaking. This needs the original .stl file downloaded and…
Updated it to work on newer Centauri Carbon sensor mount design.
Adds a bit of elevation to the Outlaw rear sight for better and more intuitive blasting. Print as imported, support 90 degree overhangs. Block supports at the holes. Install dots by applying superglue to 1.75mm filament, pressing in, and…
Thanks to @neutrOn for the remix with display adjustment. Since I don't need the USB port up front I removed it.
Fed up with having to manually adjust thread faces in Fusion 360 to give a clearance, I worked on creating an adjusted Fusion 360 Thread parameter file. Note even these maximum clearance threads will still require ‘breaking in’ so that…
Fits in the top position of the 10 inch mini rack from Geeekpi
Slightly adjusted feet dimensions and handle design, more chamfers, less overhangs, should fit the sidepanels better.
Printed using a 0.2 layer height. It will not need support if printed vertically with the tool head facing up. I would suggest using a raft.
slightly adjusted slide_coil.3mf to increase lifespan of lock. (tested with petg)
Lowpoly deer for the wall.
Print Settings Printer brand: Bambulabs Printer: Bambu P1P Rafts: No Supports: Not needed, but for port holes (USB & Eth) painted supports makes them nicer. Resolution: Nozzle 0.40mm / Layer Height 0.20mm Infill: Gyroid 33% Filament…
A remix of the base from Illia Dudnyk version
I printed the base-top-lid with supports, but I'm not sure it's required - YMMV. The shade is printed in vase mode with the instructions from the original modal.
22370 Honeycomb FTC Centerstage Claw v3 (Adjusted)- given more space, first model fit, but was too snug. Made more room.
Remix of PhilippSorenses's remix of PsychProd's original. I had the small issue, that my silica gel beads / pearls were uneven in size and sometimes broken. That led to a lot of them falling through the main container's wall. I slightly…
A hop-up tab like this one from Detroit Dartworks greatly increases the accuracy and effective range of the Rush-40, but makes the stock sights basically useless. This print fixes that. It clips onto the rear of the top tactical rail, and…
A remix of devonjones Cut-Stone Celtic Knotwork Floors. I added the OpenLOCK Triplex bases to these tiles and ensured the height was the same as the rest of the OpenLOCK Cut Stone set. I'll make sure to upload a printed/painted version as…
Ruins with high walls for the board game “Clash for Eternia” or easily magnetized walls: I have used the slicer to cut the walls above the first row of stones and added circle shaped connectors. With adjusting the dowels it can easily be…
Needed a mount for my Fluval planted light that would fit a 20-gal long rimmed tank, and saw this one made by Nolibert. However, it wouldn't work for my tank or light since it's far too small, so I made some minor adjustments. Tank grip:…
If your sliced model is showing a hole or gap along the angled edge, consider decreasing your minimum feature size, this should force your printer to put a wall there anyways. Besides that, there isn't a whole lot of special consideration…
Wall mounted paintrack adjusted for AK interactive bottles. No supports needed.
I worked this up for myself a couple of months ago and never released it because I didn't want to muddy up the waters with the adjusted belt path. When Prusa released the MK3S with the R4 Y-Idler I compared mine to theirs and saw that I…
This design remixes the original faceplate for the MK6 Funsize to suit the fysetc AIO II mainboard and LCD (https://www.aliexpress.com/item/1005004728567711.html?spm=a2g0o.order_list.order_list_main.39.766b1802RyVIiB). I have also…
I adjusted Maximilianum's great design of the AMIGA 1200 trap door with hex holes. For my Amiga it didn't work: no matter how I printed it, the latch broke. So I adjusted it slightly: 1 mm shorter and higher, with some reinforcements. If…
Remix from "Swamp boat by RCWeinstadt" I changed the rudder so that the control arm is at the same height as the servo arm. There are also holes at the pivot point for convenient mounting and a hole in the control arm. Holes are designed…
I personally had the issue that the stem kept falling out so I made an adjusted version that has a cap on both sides.
Remix of the Arducam cap/case for the pi camera mount to account for a square PCB
The magnets are in slightly different positions in the DB zeroclick cowl compared to the ZeroClick probes magnet position. (This might be because of the ZC probe versions are not followed through on the DB github.) I was afraid it will…
The EU severn model is a little too large for the Rosewill Dehydrator found on Amazon.
this is version 1. I might update. the original was about 10mm too far to the right and I changed the way of attachment.
All these files were remixed to still use the original leveling method of the Neptune 3, (strain gauge). LGX Lite Direct Drive didn't reach, so extended it out to match hole right over nozzle. With the original files of the Neptune 3 long…
This is a remix of @Kaksu3D's Rugged filament sample box remix to account for the 3.3mm thick samples (e.g. the customisable swatches from @Makkuro - https://www.printables.com/model/323399-filament-swatch). Due to the wider slits, there…
Made wider and taller and added a support bridge on at the top of the bracket for added strength. Made the holes on the base to accomodate a 3mm knurled brass insert. Printed with 6 walls and 30% infill using PETG
I used the file for the front cover and modified it to fit the 1.5 OLED display: Yellow 128x128 OLED Module SPI I2C Arduino,Raspberry Pi 1.5" inch ER-OLEDM015-3Y-SPI-I2C from buydisplay.com.
I moved the holes to line up with my kit more accurately
I recently purchased a hardware kit from KB3D.com for building the FRAKS Flexarm Heatset Insert Press. In addition to the hardware, several 3D printed parts are needed to complete the build. The designer of this elegant kit,…
The “Thumbs down BooGhost” with the white part on the left side that protrudes removed.
A friend of mine asked to print the model from carverandi to reduce the light the wallbox creates. After printing and attaching it, there was too much space between print and wallbox. So I fiddled a bit around and decreased the height.…
Took the original and fixed the symmetry along with a small scale adjustment to be closer to the base Dummy Head
Ever had a Tube of Toothpaste that was almost empty, but you knew there was still some left in it? This gadget is perfect for you! This is a simple design of a Toothpaste Squeezer. It includes rounded corners and edges to create a more…
This is a remixed and adjusted version of the HDM mod , specially tuned for PA12-CF printing . Dimensions were tweaked to compensate for PA12 shrinkage , ensuring a solid and precise assembly once printed. 🔧 What's new: Dimensional tweaks…
Adjusted the tolerances of the mounting holes so that the device won't migrate when mounted. Recommend using with two M3x6 bolts. Drill or poke through the holes.
The original arm had wide holes and I prefer simple bowden solution. Made the holes smaller and made some space for the bowden tube holding by a screw. All modification are made in PrusaSlicer. Open the project and adjust to your needs.…
remix of previous phone holder only adjusted the base and top part to fit screws, to mount it onto wood
This remix allows the use of the protector with Radiomaster Pocket Gimbal Spacer Lowered Gimbals mod installed.
Controller Scuffs with Lower Rear Paddles that are Farther away from the Controller, making it easier to access
I had trouble getting the main “left mouse button” to click. It seems like there was a lack of clearance on the parts I printed between the main buttons and the wheel mount. This model gives an extra 2mm of space to the two faces closest…
Increased size to 60mm * 80mm To fit movement https://www.aliexpress.com/item/1005001456871300.html?spm=a2g Supports for movement area and hook.
Tough roller I needed for applying a polypropylene surface to a print bed.
Moved ziptie hole from PTFE hole a bit - they were too close and the ziptie was choking down the PTFE tube.
Adjusted the front of the piece to accept a larger Micro plug and added a bit of tolerance to the front clips for the ProMicro.
A case for the Sainsmart 12864 controller, based entirely on MiggyMan's template - adjusted for M3 screws all around and modified the lid so the SD card slot is held to a minimal opening. Minimal adjustments on dimensions for clearance so…
Amazon Module: Name:DIY Magnetic Levitation Module Platform with 4 LED Lights Can Carry 500 g Link: https://www.amazon.de/dp/B07HHZCQF9?ref=ppx_yo2ov_dt_b_fed_asin_title Producer: MBLUE Manufacturer reference: 16100466 ASIN: B07HHZCQF9…
After seeing the marble maze contest, I wanted to print something similar if not better. I found the Modular Marble Drop Blocks were a possibly larger option with plenty of options to mess with. As other mentioned though, some of the…
(Remixed from https://www.thingiverse.com/thing:2786292 ) The hole spacing on the Anet Evolution X carriage didn't match my metal carriage bracket from my Alunar M505 (Anet A8 clone), so I remixed from the Fusion 360 file to match my hole…
These sticker dispensers are re-sized to fit my: Big Roll 5" diameter (up to 1" wide) sticker roll Wide Roll 3" diameter (up to 2" wide) sticker roll Tested and printed on my Flashforge AD5X & Flashforge 5M Pro using PLA filaments.
Pixelated 20739 Bumper Bracket (0.3in Adjusted)
Hey I just made a little remix to fit my LM2596 DC-DC Step Down Converter with a big square Coil. The original and beautiful design is from felixna, so please leave him a like! Finally my Sovol SV06 Plus is more silent. I also added some…
Works with PLA, too.
Full credits to @jcg67cz. Remix of some of the original components: - Separate top and knob, allows multi-color printing. - Elevated screw in bottom. Reduces breaking the screw mount of the bottom. Project file included prints cleanly…
I love the compact bowden extruder, but as always, I needed it slightly different for my application. My changes include: slightly farther out idler, to accomodate tatsu drive gear slightly different idler shape, so it fits ultimaker…
I printed my one using white ASA material using .3 mm layers in draft mode. If you care about precision and less visible lines, surely it is possible to print using more precise settings. Printing time in my case was over 3 hours.
Adjusted for Fairphone 5 size (Phone with FP case)
