909 models
I made a remix of this . I add the bottom protection in order prevent the screw to damage the PCB on the back of the bed and made some wall thicker to reduce the flex. Print the 2 parts and assembly using an M3 nut and max 10mm screw to…
I didn't find a mount for an Adafruit ADXL for the stealthburner which has wider holes so I created this one. You will need 2 M3x60 screws for the mount and 2 M2x8 for the ADXL itself and 2 M2 nuts. I hope it's useful for someone else ;)
This design is an adapter for the ADXL345 Accelerometer to be mounted on the Creality Sprite Extruder of the Ender 3 S1. There are two versions of the adapter: The first version requires 4 M3 inserts, 2 for mounting the ADXL and 2 for…
Print with standard Voron parameters. Rotate the part so that the top of the mount sits flat on the bed. Use 2 M3x8 screws to attach the mount to the ADXL holes. Use 2 standard M3 heatsets for the BLTouch mount and 2 M3x6 screws to attach…
UPDATE Added v2 (RECOMMENDED) Changelog Easier to tighten. Accommodates: Standard ADXL345. BTT ADXL345/S2DW (see this make ). 3 versions of the mount (see filenames for explanations). The bed spacer now plugs into the mount. BOM 4 x M3 x…
Inspired by the mount from pedrolamas, I remixed their .stp model into this version. It clamps to the bed of my CR6-SE and my Ender-3, with the same three screws approach as the original, except that I added hotmelt inserts and a pillow…
ADXL345 Mount for FLSUN V400. A longer screw is needed to fix it.
I am too lazy to enter what you need as screws but you only need m3 type and a couple nuts. Some holes are self threaded without nuts, you can figure it out if you inspect f3d file. Also bltouch mount is a bit high from nozzle you need…
You can buy me a coffee with a donation. Me puedes invitar a un café haciendo una donación Click to danate Update 28/10/2023 Version fysetc portable input shaper Update 01/04/2023 Version Heat inserts for adxl Bill of materials Fysetc…
CREALITY SPRITE SONIC PAD ENDER 3 S1 S1 PRO X AND Y AXIS ADXL345 G-Sensor Mount remix X axis mount more rigid and mounted permanently, sensor screw holes enlarge to fit m3 screw. To mount on sprite extruder. may need slightly longer m3…
You will need: 2pcs M3X8 screws for mounting on the head 2pcs M3X5 to fix the board on the holder
Case for Small RP2040 Boards This is a case for the small RP2040 boards such as the Adafruit QT PY RP2040 or the Seeed XIAO RP2040. These small boards based on the Raspberry Pi RP2040 microcontroller. They have a USB interface and are…
Made for the “With Voltage Regulator” type of ADXL345 boards like shown in the Klipper docs. https://klipper.discourse.group/t/raspberry-pi-pico-adxl345-portable-resonance-measurement/1757 It mounts to a volcano heater block by unscrewing…
I wanted to use an ADXL345 accelerometer to measure resonances in Klipper in my Ender-3 V2 glass bed, but there is no straightforward way to attach it, so I designed this quick mount that will allow you to get the accelerometer aligned…
…Please be sure to hit like & post a make, I'd love to see your prints! Here's my over engineered captive mount ADXL345 bed mount, it's designed for PEI covered beds of no more than 6mm deep total. Glass surfaces won't fit here! Keep your…
This fits the popular ADXL345 module that measures approximately 20.2mm x 15.5mm with eight pins along one long edge and two M3 screw holes on the opposite edge. It should be a simple print in ABS, ASA, PC Blend, nylon CF, or really…
This is a quick and simple model to mount the adxl345 to Creality style hotend nozzles.
Bracket for securing the ADXL345 accelerometer to a V6 nozzle. Available in both heat-set insert and thread tapping types. Required: One M3x10 screw and two M3 screws of appropriate length to secure the accelerometer.
Reverse engineered chinmounts camera mount for the Scorpion Exo ADX-2 motorcycle helmet. Been using it for 6 months, no problem. Make sure to print in ABS or ASA with 100% infill.
A bracket to allow the ADXL345 to mount to the Neptune 3 Pro printhead to measure the resonance on the X axis This designs uses m2 nuts and bolts to secure the ADXL345 board to the bracket. and you'll need to m3x20 bolts in to mount the…
This is a case for the Mellow Fly ADXL345 USB module. Print in your favorite filament. Use M3x10 cap screws to attach the two halves with the USB module inside. I recommend clear filament to be able to see the blue light. The case has a…
I was not happy with many of the adxl mounts that I could find. I liked that the original model used a press fit to attach the mount temporarily. Unfortunately I did not have the Fystec input shaper. The original part was only available…
A simple 2in1 mount for an ADXL345 on the Creality Ender 3 S1 / Plus / Pro or all Sprite extruders / Pro.
Ender3V3KE CR ADXL quick mount without extra screws, just using the 6 screws that coming with the sensor.
Print Instructions I recommend printing all components in PETG, ABS, ASA, or another more heat-tolerant plastic. The Pi can get pretty warm in the bottom of the case so printing in generic PLA could cause warping in some places. The 3MF…
Modeled for Ender-3 S1 Pro using right-hand stock fan mounts. Reuses stock short M3 from shroud to mount the sensor, mated with a M3 x 4mm brass insert. Requires M3 x 8mm, possibly 6mm, to replace the repurposed shroud screws. Amazon US…
I didn't have any screws lying around for the printhead mount so I moved it to a place where I could reuse the screws. Also changed the ADXL clasp so that it can accommodate a bare ADXL345 board with soldered on pin headers. I printed…
Little remix of the ADXL345 bed mount of the Neptune 3 Max, but shortened to fit onto the default PEI sheet of my Neptune 3 Pro. Fits onto PEI sheets with a hole distance of 91mm (or 81mm using the second variant). Hole diameters are 3mm.
For Radxa Zero 3W/E,use official Radxa 5519A heatsink with 1703 fan(SUNON UF3H3-700) connect to +3.3V/GND. Use 4xM2.5 heat set inserts and 4xM2.5*10 countersink screws to fasten the Cover and the Bottom. For Radxa Zero 2Pro,using official…
Latest Update: Please download the “v2” variants of the case. The original design was done using the Radxa-provided CAD, however, upon receiving my Rock 5B today, the measurements were off. I've made some adjustments to the “v2” version…
I needed a set of brackets to run the input shaping tests on my Ender3 V3 KE, and Creality makes you sign up for an account… which bugged me. So I signed up, downloaded the files, and I'm posting them here in case anyone needs them. Lord…
I wanted a secure way to mount the sensor with stock hardware, sine the other mounts for the Super Racer were just integrated or dependent upon custom effectors and hot ends. I also didn't want to make any permanent changes to the…
Hi, I made brackets to test my Sovol SV06 Plus with Portable Input Shaper from FYSETC. This specific one is slightly easier to use - requires only USB-C and flashing firmware to it. There were no brackets available for SV06, so I decided…
Simple case for the Radxa Zero3E. This is my first ever 3D design. I made 2 bases and 2 tops. The bases have two options: One with all usb and micro-HDMI connections and another with just the usb-c to power the thing for preset tasks. For…
An X axis mount for the ADXL345 inspired by @FLYNINDUSTRIES's bed clamp mount . This mount was designed for the Neptune 4 Pro but may work on other models leveraging the metal guide rails. Please note that someone has explicitly tried…
A bracket to allow the Adafruit ADXL345 to mount to the mini-afterburner in order to do pressure a advance. This designs uses m2 nuts and bolts to secure the Adafruit ADXL345 board to the bracket. and you'll need m3x40 bolts in to mount…
…Please be sure to hit like & post a make, I'd love to see your prints! Here's my over engineered Y Axis captive mount for the Fysetc Portable Input Shaper ADXL345 USB C Accelerometer bed mount. It's designed for ANY PRINTER with a PEI…
(Files belong to their respective and linked owners.) Please email/contact me for immediate changes such as incorrect credit or placement, etc. I take no credit for any of these designs except for the extremely basic remix of some of the…
To use an ADXL345 (possibly similar), and a Raspberry Pi Pico as an input shaper for Klipper systems as a secondary MCU. Programming settings, and wiring were pulled from NERO 3D and the following video:…
Great idea how to easy and quick mount cleaning brush to the bed - I used mount from cleaning brush for adxl345 mount to the hot bed. Many thanks both of designers - Alehandoro VR and Rui Reis
Snap on Lid and Base 3mm mounting holes a lid, base, and a button up to 50mm fan mount Use a piece of filament for the button hinge. Version 2: widened by 2mm for easier fit, added a little extra thickness to larger IO cutouts. Have a Q6A…
Permet de fixer le ADXL345 Fysetc comme la sonde de nivellement. Fonctionne pour la V400 et la SR. Prévoir un aimant de 10x20x3mm (moi j'ai simplement coller l'aimant, mais j'ai prévu un trou pour le visser) et 2 vis M3x8 pour fixer…
A remix of mgrupe82's Adafruit ADXL345 90 Mount for Micro-Swiss NG , with a solder cutout and widened slots for screws to fit more board designs using the ADXL345 accelerometer besides the larger Adafruit model. Designed to be a permanent…
Use minimal 3 perimeters and as much infill as you like. The mount slides on the plastic lip behind the ribbon of the extruder. Make sure you to resize it if necessary so it fits tightly. The flat "wings" are for mounting it to the bed…
ADXL345 accelerometer V6 nozzle mount for input shaping. Couldn't find one which doesn't fall apart immediately, so I design a robust one myself. You'll need: 3 x M3 nuts 2 x M3x12mm screws (ADXL mount) 1 x M3x10mm screw (nozzle clamp)…
This design mounts the BIGTREETECH (BTT) ADXL345 2.0 accelerometer board (https://www.amazon.com/BIGTREETECH-Accelerometer-Klipp-er-Connection-Stealthburner/dp/B0CHJQ6CXF) to the bed of the MK3S+ or any bed that is under 5mm thick. Use a…
Ender 3/6/10 adxl accelerometer mount for x and y axes, not tested on ender 6 and 10 but should work just fine The x axis mount gets screwed directly to the hot end for the best and easiest measurements I recommend to print with 3 or more…
This is inspired by snap fit cases that I've seen for Raspberry Pis. None of them were an exact fit, so I made this one from scratch.
Anycubic Vyper PEI ADXL345 Y-Mount Mount for KUSBA ADXL345 and ADXL345
A simple, single use mount to hold a Bigtreetech ADXL345 or S2DW accelerometer for input shaper calibration of the Y-Axis on bedslinger printers. Print in the center of the bed, then attach the sensor. Print with Brim for extra bed…
Use this part to mount an ADXL345 to an E3D Revo nozzle Two M3xD4.6mmxL5.0mm heat inserts are used to affix the ADXL345 to the holder.
Modification to the beta ADXL mount to combine a BLTouch mount. This was designed for the Ender3 Switchwire conversion and should work for the Switchwire. Community feedback indicates it might interfere with the belts on other Voron…
Radxa Zero case with heatsink and GPIO slot
For one of the most common generic type of ADXL345, see picture (15mm screw hole distance and about 20x16mm PCB dimensions) Print the M3x4 or M3x6 model, once the print is done, set the bed to stay hot (don't let it cool too much or…
Remixed to use with Fly-ADXL345.
This is a case I made for the Radxa Rock 4 SE using TinkerCad. It's easy to print without supports or rafts with PLA or PETG. Version 2 places a 40mm fan inside the case with ample space for the heatsinks. The nvme ssd version is shaped…
Mount your Kusba ADXL345 USB accelerometer quickly on probably any toolhead directly to your nozzle to get most accurate readings BOM (I used for my build) M3 20mm x 2 M3 6mm x 2 standard 5mm Threaded Heat Set Inserts x 4 Please let me…
Nozzle Mount Adapter for an ADXL with 15mm hole distance. BOM: (3mm holes in bottom plate) 2 M3 Heat Inserts 1 M2 Heat Insert 1 M2 Screw BOM: (2mm holes in bottom plate) 3 M2 Heat Insert 1 M2 Screw
I wanted a case to hold my Radxa SATA HAT and drives securely and without just leaving them to get knocked over. This is a quick and dirty answer to that. It doesn't have an opening for the eSATA port, and the power ports could be a…
Magnetic Mount for ADXL345 Accelerometer This design is a detachable mount for an ADXL345 accelerometer to be used with Klipper 3D printer software for measuring resonance for its Resonance Compensation (aka Input Shaper) feature. The…
Dvoudílná skříň pro počítač Radxa Rock Pi 4 Plus připravená k montáži ventilátoru 40x40 mm. Rozměry krytu umožňují použít lepený chladič procesoru + vnější ventilátor nebo dovnitř montovaný ventilátor se sníženou výškou. Materiál: PLA…
◼ Voron Stealthburner CR Touch ADXL mount mounts to the original ADXL mounting position on the Voron Stealthburner with a V6 hotend and provides mounting for a CR Touch. CR Touch probe offsets: X = -44.337 mm Y = -1.093 mm ◼ Required…
USE AT YOUR OWN RISK - Sounds a little dramatic, however if you use this mount then the end-stop switch will no longer trigger. Instead, the ADXL will crash into the motor cover. To work around this, I just triggered the end stop myself…
Print with PLA on a flat side without supports, so it looks like an L from above. Use M3 or similar screws to mount the accelerometer to the part and itself to the extruder (check picture 1)
This is a remix of https://github.com/VoronDesign/VoronUsers/tree/master/legacy_printers/printer_mods/meteyou/gcode_buttons to fit on a voron 2.4 to mount a adxl socket New MMU parts addet for mmu in super Slicer. add part then right on…
This is a simple remix of a remix - because I love heatset inserts. Credit to Anatoly Kharkov for the ingenious dual purpose clip/mount design: Fits both the X and Y axes for the Ender-3 V3 SE The clip is a nice secure fit on the bed Easy…
Increase air flow for SATA drivers Opened the window for OLED display All screws are now using m2.5 Fixed the opening for pi5 USB Fan openings are bigger. The chamfer for bottem plate now are 45 degree for easy printing Remove useless…
btt adxl bed mount using m3 hardwar m3 5x4mm heat insert for clamp to bed m3 x 6mm hex bolt m3 x 3mm/ 6mm max hex bolt
This should fit a standard ADXL screw spacing and is designed to clamp to the print bed and axis of an Ender 3 with a magnetic plate on the bed. I also have an orbiter 2.0 extruder on a custom mount. It has been designed with this module…
Resonance probe for input shaper calibration for the Klipper firmware based on a RP2040 Zero and a generic ADXL 345 Sensor SPI breakout board.. Wiring: RP2040 ADXL 345 GPIO 0 SDO GPIO 1 CS GPIO 2 SCL GPIO 3 SDA GND GND 3.3V VCC…
There are a few files, Please choose the correct one for your use case. In PrusaSlicer, Right Click → Split to separate into lid/body. Print with Tree supports!!! ** 25/05/10 - Removed bosl2 dependency, added options [less_fans, shrink,…
I did not like the mount that came with the Stealthburner files since the X and Z axes were swapped. I redesigned the mount so that all axes are aligned. The mount attaches to the two inserts designed into the Stealthburner for this…
This design replaces the extruder idler with one that has mounts for the BIGTREETECH (BTT) ADXL345 2.0 accelerometer board (https://www.amazon.com/BIGTREETECH-Accelerometer-Klipp-er-Connection-Stealthburner/dp/B0CHJQ6CXF) for use with…
This model can be attached to the Ender-3 S1 hotend and bed to mount the ADXL345 accelerometer. A single M2 screw is needed for the hotend attachment while it clips on without a screw to the metal plate under the bed. Make sure to place…
ADXL345 mount Ender 3 v3 SE Category: 3D Printer Accessories
ADXL345 Accelerometer Sensor generic Mount on 4010 Fan
The original dragon burner ADXL mount needs a longer M3 screw. so I adjusted the mount with a sunken screw hole that uses the same m3 screw. !!DO NOT OVER TIGHTENING!!
You should need 2x m3x60mm to mount it to the stealthburner. i used M3x12mm with nuts to attach the mount the adxl. please note: voron stealhburner does support adxl mounts by default, check:…
These are mounts for a Mellow Fly ADXL345 accelerometer for an Elegoo Neptune 4 (Pro) 3D printer. Compared to other mounts that attach to the back of the extruder they work for the non-Pro and Pro model. I've designed them to use a total…
I “remixed” the original extruder lever brace from https://www.thingiverse.com/thing:3935900 . Main reason was to be able to mount a ADXL345 sensor. I had to calibrate klipper3d with help of this sensor. You can just put the ADXL345…
This is a case for the Radxa X2l. Case printed with Inland PETG. Button printed with pla. Use 2x8mm screws. Made a window for the power LED using clear UV resin (not required). Printed on Bambu labs P1S.
Two versions of the bracket: With thread - for printing on an SLA printer No thread - for printing on an FDM printer BOM: M3*6 screw - 2pcs - I recommend nylon M2*8 screw - 1pcs M2 nut - 1pcs
I've printed a custom fan duct for my Ender 3 V2 and I didn't want to re-print everything just to mount the ADXL onto it. Instead I got highly inspired by this drag chain mount. I designed my own based on this simply because I liked the…
This is a mount for the FYSETC USB ADXL345. It mounts easily to most Ender 3's and its clones (I am personally using this on a Voxelab Aquila). It mounts easily and securely to the printer by sliding it firmly onto the X and Y Gantry.…
Just a simple remix for mounting the input shaper sensor. I used 2xm2.5 bolts to mount the sensor. Can very probably use what ever came with the Sonic Pad, but I lost those.
Needs 2x M3 40mm bolts 2x M3 x 5 x 4 mm heat inserts 2x M3 6mm bolts
A mount for the Ender 3 S1 Pro and other models with the same print head to use the ADXL345 that comes from BigTree Tech. Mine came with he BTT-Pad7. Allow for mounting to the bed with a clip or tape, and to the side of the print head by…
Designed for Ender 3 V3 SE but will fit any 42mm stepper motor with threads. Use 2x M3x6 for the stepper holes, 2x M3x8 for the sensor (both brackets). Use a binder clip for the bed mount.
This mount can be used either on the printer head (with screws) or mounted on printer bed (with binders) There are 2 models - one for regular nuts and one for heat insert nuts. heat insert nuts dimensions - M3, outer diameter - 4.2mm,…
Modification of the https://www.printables.com/cs/model/597996-mellow-fly-adxl345-stealthburner-mount. You should need: 2x M3x8 2x heat insert 2x M3x60
Here is a single ADXL345 mount that can be attached securely and out of the way to the extruder stepper motor to measure your X resonance frequencies or to your bed using a binder clip to measure your Y resonance frequencies. Versions:…
a simple housing for the adxl345 sensors that can be quickly and easily attached to and removed from the printhead and printbed with double-sided adhesive tape. with the original, the contacts on the back were exposed and the two holes…
Hi, I made brackets to test my Sovol SV06 Plus with standard ADXL345 chip, altered from my other PIS ADXL345 input shaper, so photos are visible there for now. All holes are measured for self tapping, no need for heated thread inserts.…
A Pi Pico 2040 case for those using a Pi Pico + ADXL345 as a portable solution for doing Input Shaper measurements with Klipper. Can accommodate 6 wrapped wires or a Cat 5 cable going out to the ADXL345. Dimensioned for PLA. Scale to…
Update 2024.06.19: Added a variant that can fit several models of accelerometer: BTT S2DW 1.0 (tested) BTT ADXL345 v2.0 (tested) Mellow Fly-ADXL345-USB (untested; should be OK in REV6) GY-291 / SparkFun ADXL345 (SPI) (tested) GY-521…
A simple bed mount for your FLY ADXL345. You need 2x M3*6 screws (or shorter) 1x foldback clip
A compact case that firmly holds a S2DW or ADXL345 module from BTT. It's got a acess window to the root button and a small hole to chek on the status LED. If you use longer M3 screws it's possible to mount it on any surface you'd normally…
