Counting matching models…
This is a canopy for the BetaFPV Air Tinywhoops, like the Air65 and Air75. The longer tail section allows a lower camera angle to be set. I also made a widening in the area of the right holder to additionally fix the antenna connector. I…
Case for the BetaFPV Air75 Tiny Whoop. The case has a modular design so it can be used for different battery numbers. The Case consists of the Case itself and a Lid to close it. Also a storage insert for four batteries (Lava 1S 450mAh)…
Someone in the comments mentioned that original canopy is too thin for TPU so I added 0.5mm thickness for it
Travel Case for the BetaFPV AIR75 that holds up to 12x Lava 550mah (smaller also works) as well as spare props and more!Travel Case for the BetaFPV AIR75 that holds up to 12x Lava 550mah (smaller also works) as well as spare props, the…
This tiny bit of plastic lets you decrease the tilt you can apply to the camera on the Air65 and Air75. This lets you fly slower and still see straight ahead. Weights under 0.1g, which is probably less than most of the other solutions…
I printed mine out of PLA, but I would recommend TPU. It mounts the camera at a 35-degree angle. It mounts on top of the U.FL socket to hold it down, as I found it would always come out with the stock design.
Bought this keyboard, but was unhappy with how low it was. I've designed new feet, which are twice as higher. If you go anything higher, then the rubber feet at the lower part are not touching the surface and keyboard slides. You need…
75mm Tiny Whoop Hard Case Air75. This is a remix of spectrexFPV Whoop case to fit betafpv air75 and other similar drones
Air75 case, uses an M6x45mm screw. Holds 12x Lava I 550mah or Lava II 580mah cells. Case includes a tongue to lock the whoop in place using the battery holster. Category: R/C Vehicles
“Made for the Tiny Whoop Pinch Camera, and Diamond Style Flight Controllers. You will have to cut 75% of the front post on the BetaFpv Air75 Frame and shave a little plastic off of the bottom of the frame under the front post.” Copied…
I bought some prop remover that I thought matched the one the original tool was designed for (based on the images from the Amazon seller), however when I received the product it was not. It was more angled which caused the sim tool to not…
I couldn't find a case to fit my Air75 and a v whoopster together. You can also add batteries in rest of the compartment Print suggestions: 15-20% infill Print with flat size at bottom Features: Requires no support. Snap-on fit
Knob I quickly designed to replace the knob on the Nuphy Air 75 V3 to spice it up a bit. Print in the orientation shown in the image with both the Base and Ghost upside down on the buildplate. I was able to print with no supports and…
lightweight Battery holder for the BetaFPV Air75, to help to slightly swollen battery, or help centre balance with the battery. Also has the advantage of fitting other batteries that might not fit otherwise. helps the drone take off on…
Rugged case designed for BetaFPV Air75 II. You will need m3 30mm screws total. I set up 5 wall and 25% infill with honey structure. PLA work great for me.
The case can carry four 1S 450 mAh batteries and Betafpv BT2.0 charger. I also installed inside a magnetic strip to attach prop removal tool. Print with PLA or PETG. After printing the bottom part, four 5x5 mm magnets need to be inserted.…
Three-spoke knob fitting for the NuPhy Air75 v3. Print the stem and either chubby or skinny knob.
This is a 10mm riser feet for the $45 Nuphy Air75 clone sold on Aliexpress, like https://www.aliexpress.com/item/10050058 . It's a tight fit on the original magnetic feets so you may have to deal with your XY compensation, no need for…
Print in place latch-box for a 75 mm tiny whoop FPV drone with additional top-insert (for things like props, canopy, usb-adapter…). Tested with the Air75 from BetaFPV (Check the mesurements of your whoop beforehand. Fusion360 files are…
I had to edit the screw mounts for better grip to the Flight Controller and the Body and also make the camera scew thicker because there was not enough grip and my camera was rotating when printed out of TPU. - Screw holes have a thinner…
Air75/Air65 Canopy with extended lower arms designed to protect the camera more than the standard mount does. Frame it is designed for: https://www.printables.com/model/217934-tiny-whoop-frame-1s-31g-auw In my build, I use M2x20mm screws…
Integrated keyboard wrist rest for NuPhy Air75 V1
I couldn't help but add some eyeballs to my BetaFPV Air75. Watching a drone fly around really makes you think it has a life of its own, and adding eyes gives it a personality. This is a very simple model that absolutely destroys the…
In order to use the other prop tools such as https://www.printables.com/model/738324-whoop-prop-removal-tool or https://www.printables.com/model/1102461-micro-whoop-prop-removal-tool-air75, a clearance is needed to get the tool under the…
Use a 3mm woodstick for the clips.
An extender for the canopy of the BETAFPV Air75 FPV drone so the camera can look lower than 25 degrees
This holder is designed to securely hold the BETAFPV Air75 II upside down while working on the drone. It is especially useful for soldering motor wires, repairing the flight controller, replacing components, or doing other maintenance…
Overview Turn your BetaFPV Air75 II Champion into a budget cinematic cruiser! This adapter lets you mount an SQ11 HD Camera to record 1080p footage without modifying or soldering anything on your drone. Instead of modifying the top…
replacement feet for nuphy air75 v1
I couldn't help but add some eyeballs to my BetaFPV Air75. Watching a drone fly around really makes you think it has a life of its own, and adding eyes gives it a personality. This is a very simple model that absolutely destroys the…
![[Better screw-holes] BetaFPV Air Canopy - For Air65 and Air75 Tinywhoops](https://media.printables.com/media/prints/f5502fc3-d1a1-4daf-b969-8298113e9d2e/images/13729488_bdb2cf81-db19-4906-947d-9d2cbb7b5656_d3d0f7c8-a33b-44b5-9990-82c4666a81f4/20260903_181357.jpg)
