Counting matching models…
Made this desk stand after a conversation on the AirGradient forums that there should be some airflow to the bottom vents. https://forum.airgradient.com/t/calibrate-humidity-sensor/994 Best to print flat on its back and add some support…
This is a replacement case for the AirGradient DIY air quality sensor that uses the v2 PCB. The biggest problem with these devices was that the temperature sensor was mounted directly on the PCB and would always read a few degrees high…
I took the design shared by forum user ‘ ttielemans ’ found here and added a 50 degree dovetail sliding LCD cover. That LCD is quite bright if you're using it in a bedroom and trying to sleep or if you just don't want to see it all the…
4x M3-30 screws + 4 inserts are needed. https://cnckitchen.store/products/schraube?variant=47867092009295 + https://cnckitchen.store/products/gewindeeinsatz-threaded-insert-m3-standard-100-stk-pcs The connector i used:…
This DIY enclosure for AirGradient Basic DIY indoor air quality monitor was inspired by my Ecobee thermostat. It features a baffle to separate the PM sensor fan intake and exhaust and it features a separate enclosure to isolate the…
Needed a wall mount with a back passthrough for powering it over a POE to USB-c adapter. Can be used with the existing cable guides
After watching this YouTube video by Jeff Geerling . I printed and built the Air Gradient. In Jeff's video, he mentioned that temp sensor might give higher readings because of it's locations in the case. I noticed what I believe to be…
I wanted to have mine mounted at a certain angle so I could see the screen better while its tucked into a corner. I have provided the .stl, .step, .obj and .f3d files. I did not have to print this file with any supports as long as you…
AirGradient is a great open source air quality monitor, and I keep one next to my 3d printer. Rather than stick it directly to my wall, I remixed Handro's desk stand (thanks for using Onshape and making it even easier!) with my HSW…
Using the attached m3f file, you can print this with minimal supports that are extremely easy to remove. I used PETG, but I think there would be no issue using PLA or whatever other material. To attach the holder to the HSW use one of “…
A simple mounting bracket for the AirGradient Outdoor Monitor. Can be attached to screws or mounting tapes / command strips to walls.
Can mount the holder to the wall using 3m command strips and then slid the airgradient in and out. I've upgraded a few sensors & had to debug stuff on my airgradient and it was annoying to take off the wall previously. The file attached…
I wanted to run my Airgradient O-1PST outdoor monitor inside next to my I-9PSL indoor one to compare the readings. I needed to get the O-1PST off the counter, so I designed a stand to hold it up in the air.
I soldered ESP right on the board but made display detachable. This way I got display sitting 6mm lower then top of PM senser. If you did the same, this case might look better for your setup. Locate all items surface down so you don't…
Couldn't find a wall mount for the AirGradient ONE, so I made one. Mounting directly with screws is tricky since lining up the keyholes with hardware in the wall is a pain. Designed in Fusion 360. Mount goes on the wall first, monitor…
Remix of the "Top Side" part from CaptainPotatoFudge's model to accomodate 1.5" OLED display from WaveShare.
This 3D printed pipe holder is designed specifically for the AirGradient Outdoor O-1PST sensor and allows secure mounting on a 28 mm diameter pipe . For outdoor durability, printing in ASA is strongly recommended due to its UV resistance…
Adapted the AirGradient desk stand to allow mounting the DIY version securely. The case Snaps in place. I personally used the version with a cutout for the temp/hum sensor to give better readings
Mount your AirGradient ONE (I-9PSL) to an IKEA Skadis wall system with this model. I recommend that you print the model on its side with organic supports. Works fine with PLA and 5% infill -- it does not need to be super strong.
Decorative or prototyping piece that visually simulates the printed circuit board (PCB) of the AirGradient ONE air quality monitor. Designed for 3D printing, this replica reproduces the dimensions and component layout of the original PCB,…
Decorative or prototyping piece that visually simulates the printed circuit board (PCB) of the AirGradient ONE air quality monitor. Designed for 3D printing, this replica reproduces the dimensions and component layout of the original PCB,…
This 3D printed pipe holder is designed specifically for the AirGradient Outdoor O-1PST sensor and allows secure mounting on a 28 mm diameter pipe . For outdoor durability, printing in ASA is strongly recommended due to its UV resistance…
Couldn't find a wall mount for the AirGradient ONE, so I made one. Mounting directly with screws is tricky since lining up the keyholes with hardware in the wall is a pain. Designed in Fusion 360. Mount goes on the wall first, monitor…
