Counting matching models…
Included are two styles of side brackets for your own DIY Eurorack case and its Gie-Tec rails. Both the 3U and 1U (Intellijel) brackets include countersunk holes for M5 flathead screws for mounting the rails, and M3 flathead woodscrews…
Brackets are fixed to the drawer front and back with 10mm 6g countersunk woodscrews and a suitably sized 6mm threaded rod (print brackets have 6mm thread designed in). The threaded hole is offset to allow it closer to the drawer bottom to…
4 hole version has 8.5mm (for M8) holes spaced at 45x60 2 hole version has 7mm (for M6) holes spaced at 72mm
This heavy-duty bracket is perfect for making bigger keyboard tray that has also plenty of space for mouse movement. Furniture board that I used is 86cm x 30cm x 2cm. Whole assembly feels very sturdy. The idea was to only print it once.…
The mounting brackets have 5mm holes for screws. The tenda switch has the following dimensions: - Width: 101 mm - Length: 100 mm - Height: 26,5 mm Happy printing and mounting :)
Part of my collection for furniture: https://www.printables.com/@MichaMietlins_755343/collections/3218237
Cable brackets for both a single cable and multiple cables. You can screw these brackets to a surface but also, for example, stick them to a surface with double-sided tape. Set the infill to 100%.
I wanted to put my 52Pi ICE Tower Cooling Fan on my Raspberr pi 5 but the brackets were incompatible due to the PoE header. So I made my own. The 52Pi ICE Tower Cooling Fan was originally made for the Raspberry pi 4, but these brackets…
If like me you buyed an a older version, you may noted that is a little more large than the printer, here is the fix
Rear kitchen drawer brackets, marked left and right, with a .25" lip.
E N G L I S H Accessories for 50 mm brackets and 28 mm curtain rods 1x 5 mm spacer small 1x 5 mm spacer large 1x 3 mm extension for spacer 1x connector for curtain rods, rigid 1x connector for curtain rods, for sliding These parts are…
You will need 2 x 1-inch (25.4mm) diameter pipes (any material, the loads are very small). M5 threaded inserts are used and space was designed for them to be installed conveniently, M4 inserts will work in theory. 4 x 12mm long screws are…
Instead of the original zipper, I designed a clip for the swing arm to attach the wire and PTFE tube. Four pieces need to be printed, the models are numbered: one piece of the one, two of the two and one of the three. I printed it out of…
This system is great for photographers, makers, or artists who need a reliable and portable lightbox setup. Add LED strips or diffusion sheets for best results. Features: Designed for wood cleat measuring 20×36 cm Works with 12 wood…
UPDATE: 4 June 2026 - Decided to revisit the design and created a slim version while still ensuring strength. This provides a way to secure the Miter Saw, using the (DW7231) Miter Saw Stand Tool Mounting Brackets, to the slatwall. Secure…
These print files do not come with a warranty. They are not meant to be permanent solutions for a broken door latch, as 3D prints can be brittle and unstable, especially in an environment like this. Please properly replace the parts in…
Brackets to mount a Quad Cortex without the use of any double sided or hooked tape shenanigans. I have mounted it in a case where the wireless system, power, and MIDI and CAT connections are hidden in. For the right side, take a look at…
This kit improve; the access to the block with is angle, the bracket better fixe of the hose to the wall with nice look and one of the bracket can hold the blow gun whit metal tip and plastic handle. All made in PETG.
Simple 160mm bracket you can use to fix your telescope to a dovetail plate. It is compatible with Hadley tube rings: https://www.printables.com/model/224891-hadley-scope-family-adapter-for-tube-ringsequatori Additional material: 4x M4x30…
These small brackets let you place your iPad or other tablet on the wall. This is very useful for example if you use a recipe app and want a convenient way to view them in your kitchen. The front corner was designed not to cover any part…
I designed these brackets to mount a network switch vertically on a wall or under a shelf. They fit perfectly with: ✔ TP-Link TL-SF1016 ✔ Tenda TEG1024D Recommended Print Settings: Wall/perimeter thickness: min. 4 Infill: 20% or more…
Replacement brackets for the Urban Worm Bag, both versions 1 and 2 (v2 found at the link below). The example image above shows versions 1 and 2 stacked together.…
I found Andrew's design quite useful as it rigidly fixates the switch, even when (un-)plugging ethernet cables. The present design has openings for better ventilation, since the original design was blocking the vent holes present in my…
L brackets, sturdy with inset for wall anchors. I release this in public domain.
This heavy-duty bracket is perfect for making bigger keyboard tray that has also plenty of space for mouse movement. Furniture board that I used is 86cm x 30cm x 2cm. Whole assembly feels very sturdy. The idea was to only print it once.…
Print for holding various small switches and LEDs. Made for a Suzuki V-Strom DL650 but should work for other models. The middle slots are used for small zip-ties, to affix to the handlebar. I release this onto public domain.
Summary This is a spray can holder with brackets to be used on a IKEA SKÅDIS pegboard. The holder has a 66 degree tilt and is stackable sideways (and of course vertically, depending on what bottle you are using). The holder comes with a…
Dlocks are expensive , I dont like existing wheelchair brakes , so have d'locks , however they have broken many spokes over time and broken my spingery wheels , so I have printed the hub bracket the that spreads the loads across the wheel…
This is a custom wall mount bracket set (left and right holders) designed specifically for the Levoit Vital 100S air purifier . These brackets allow you to securely mount your air purifier to a wall, freeing up floor space while…
I designed these mounting brackets to allow installation of Kicker 51KST2004 tweeters in place of the Hyundai Ioniq 6's factory tweeters more securely than using tape as is usually done. To put the tweeter in the bracket, put the tweeter…
Mounting Brackets for Chanzon 12V 5A Power Supply 60W https://www.amazon.com/110V-220V-Converter-Lighting-Transformer-Flexible/dp/B073QTNF9F
NB : la description figure également en français sur l'Air du Bois Introduction I needed to mount two shelves in my bathroom after it was completely redone. The shelves are located between two walls and support little weight. However, I…
brackets for holding up a shelf can take very heavy loads more than 40 lbs per bracket costs about 5 cents to make using PLA
The rear suspension of my TT-02 felt far too stiff, even with the Soft springs included with the Tamiya CVAs. These brackets bring the mounting point 7mm inwards. Notes: Designed to be used with Tamiya CVAs (TAM54753) Need 4x 3x12 machine…
Can fitted without removing original nuts (and f-ing up the original adjustment of bonnet) Bolts on top of OEM bracket with a large m8 Washer and hex nut Supported on top of bonnet (add VHB tappe) Should be printet in a strong material -…
1st week printing and designing and already I want to upgrade to a larger printer with multi-filament. This set of brackets requires a dowel less than the 22mm hole and a set of ring stops on one side to secure after loading up with rolls…
I used PETG with 5 walls and 100% infil. used the counter sunk waashers to prevent th e construction screws from slpitting the layers
Simple design which makes your desk looks cooler as a programmer, coder, and developer.
This model is perfect for showcasing your Commodore 64 and keeping it ready for use! It works well with both vintage and the new C64 Ultimate bread bin style Commodore 64s. Plus, it’s a quick and easy print without any supports, which…
If you purchased any RAK Unify enclosures, such as the RAK Wismesh Solar Repeater Mini for Meshtastic, you'll need some mounting brackets. The default kit doesn't include them, so I've made some based on RAK's own design documents. They…
I have a second-hand IKEA wardrobe that's at least ten years old, maybe twenty. It wobbles. Instead of buying a new wardrobe, I made a few brackets and fixed the wobble. Parts Rod holders: to replace the missing Levelling shims: slide…
The original top brackets did not fit properly (likely due to a different printer or LED bar revision), so I designed new ones that are wider and fit perfectly. You will need 2 x M5 nuts to slip fit inside the brackets for mounting the…
Here are some shelf brackets for the X-Arcade Arcade2TV-XR pedestal. The brackets for the top shelf replace the rubber covers and are specifically for anyone who upgraded to the Haptics kit and has an extra top from that. The side…
BOM: Printed with ROSA3D High Speed PLA Light Gray A comprehensive collection of solid, reinforced corner brackets designed for structural projects, DIY repairs, woodworking, or 3D printer frames. Key Features: Reinforced Structure:…
NOW UPDATED TO NOT RELY ON ADHESIVE -- USE 3MF FOR UPDATED GEOMETRY AND SLICING PARAMETERS Use the preexisting 3X M3 plastic screws to mount the bracket on each side, then use double sided adhesive to mount your strips to the brackets.…
These brackets were designed to be used in pairs. The top has notches to clip into the veins of common RO filter housings. The bottom bracket is smooth and used to hold the housing away from the backing board. Printed in PETG, 30% infill,…
My welder broke so i had to solve things with what i had. Here is the 3D-printed corner brackets for my offloading table. Brackets are pressfit, fitment is tight and depending on filament and printer precision. Full structural strength…
Custom-designed wall mount brackets for securely displaying your Goosky S1, S2, and RS4 helicopters. These mounts provide a clean, space-saving storage solution while keeping your heli protected and ready to fly. Features Designed…
I made this model to display my wife's Lego botanical collection. I wasn't able to find any shelf brackets that would go with the theme of Lego so I made these oversize Lego bricks to mount a section of wood to the wall to properly…
Straight edge brackets for mounting objects to a 10x10mm M3M grid using M3 hardware. Pill adapters have pill-shaped slots in them with mounting holes conforming to the 10x10 grid. The pill can accept a pill with a post or other shape, so…
Make precise door installation easier with these practical brackets. This small tool allows you to quickly and evenly al
These brackets create a floating outer frame around an already stretched canvas. They are decorative and alignment pieces, not structural supports for the canvas itself. The intention is to help you build minimal frames for canvas artwork…
Created in Shapr3D. Instructions can be found on Github: https://github.com/maksimdrachov/matrix_display
Introduction When I decided to assemble my HomeLab Rack I wanted each device to have its own dedicated holder, as I like to keep everything tidy and wanted to avoid a mass of shelves. Unfortunately I couldn't find any satisfactory…
Brackets to mount NVR under desk. I added pocket cutouts to allow TPU pads to prevent vibration being transferred to the desk.
Wanted some half shelves for the same reasons as the original designer, the dimensions you need for these are 6" x 0.5" x (shelf length)"
The Jonsbo D32 case is a really cool and compact case, but its small dimensions pushes the user to find different air cooling paths. One of these paths sees a back intake and top exhaust but the case lacks both a back filter and a…
The 2 parts are printed standing upright on the back face without the need for supports. (I did enable supports to have nicely rounded screw holes but not essential). You can mount them using 3 wood screws or double sided tape. The…
These brackets fit onto Omniwall metal pegboard panels with the correct spacing to hang rows of GunplaMark's Filament Storage 2026 containers. Spacing will allow 6 dryboxes across a 32" wide panel. Both STL files will load into your…
These brackets are needed to modify the Flashforge AD5M printer so that you can properly install the filament servo tray onto the back of the printer. This is to modify your printer so you can print in 4 colors. The upgrade kit can be…
The 2 parts are printed standing upright on the rear/back face without the need for supports. (I did enable supports to have nicely rounded screw holes but not essential). You can mount them using 3 wood screws or double sided tape. The…
Refresh version of mounting brackets for the MikroTik router (tested on RB750Gr3, hAP lite and hEX Refresh) to mount on a standard 35mm DIN rail. The model is provided as a single STL file. The bracket is not symmetrical, so you will need…
I designed a fairly simple spool holder for Ikea Pax. You will need two KOMPLEMENT clothing rails (302.568.91). It is compatible with all three sizes: 50cm ✅ 75cm ✅ 100cm ✅
Introduction I've collected a number of 3dfx Voodoo cards missing their brackets over the years. Of course I had to create replacements for them to make them functional again. Here is a convenient collection of those. My designs require a…
Two brackets, intended to support 1x4 and 1x6 boards between floor beams exposed in a basement. For my purposes, they were used to hang an AC Infinity carbon filter above my 3D printers.
Those are brackets made for the Ncase M3 allowing you to mount front intake fans. They look good, they are well secured and make the grater pattern worth it!
This is a collection low profile brackets for multiple ConnectX cards. They may work on other Connectx cards with similar mounting points and port count. Mount distance is the length between mounting holes. The screws seem to be 4-40. I…
Fillament shelf bracket, as pictured. I tested a single bracket up to 4kg and then ran out of stuff to put on it and it didn't flex. I suspect the PVC pipe will be the weak point as that flexes a lot more. Although this is mounted to a…
I needed a custom-sized shelving unit, so I used 20x20 mm profiles and 18 mm thick boards. The design requires no supports and is optimized for PETG printing. In V2, I adjusted the top bracket for the upper board to achieve a cleaner…
Summer Adjustable Baby Gate Wall brackets Printed in PETG 1 of each file will be needed to mount per end no supports needed print screw threads with solid infill Original screws thread directly in to the printed parts
I designed this for my roll cage for ambient lighting in my sim rig. The Roll cage is made from 40mm pvc pipe the OD is 43mm
Designed to fasten 1.25" SQ wooden posts to make cubes with flush edges. Not intended to be particularly high load capacity, but I've now built quite a few little (500mm on a side) cubes with them and they are working just fine for my…
Was missing some mounting brackets for my whiteboard. The original ones I wasn't able to find to be bought online, so instead I designed ones myself. The brackets work on whiteboards where the mounting frame have indents to hook onto the…
Remix of Markuzzzi's IKEA Skydrag LED light brackets: https://www.printables.com/model/530174-ikea-skydrag-led-light-brackets Modified them so they mount nicely (I think) to a shelf. Also included a notch to tuck away the cable. Shelf in…
remixed this bird feeder and added a bark texture to give it a natural look. I also removed the camera bracket
I just measured the original bracket. "Zprobe Ender3V3SE.stl" should be a perfect fit replacement. 5mm shorter should account for normal height heat blocks which I needed to make ~~2mm longer should account for volcano nozzles / heat…
Brackets to securely mount the “ Star-Mount flat mount ” on the roof of a car / truck and still be able to remove the dish. Print in ASA (or ABS / PETG, not PLA) Layer height should be something between 0.26mm and 0.32mm ≥ 30% infill, 4-5…
Allows the use of Bowden tubes from Dry boxes on a Ender 3 3V SE or other printer with the same spool holder.
Two brackets are included, one with a hole for the blue power LED, one without. PLA color in the picture is Prusament Azure blue, PRM-PLA-AZR-1000. The original brackets are designed for and tested with the 230V MeanWell power supplies…
English: An ender 3 v2 was used to print the model, no supports required. filling: 30% layer height: 0.3 Two files were added, one is a bracket for the left side of the shelf and the other for the opposite. It is printed in one piece so…
Something to stand a power bar on edge behind a television. Power Strip Edge Stand Command Strip Brackets for 1" (26mm) Power Bars. Left and Right, End and Mid mount. Recess for Command Strip small poster.
Brackets for building a DIY shelf out of a 1x10 or similar shelf board. Designed for X1C print bed (256mm * 256mm). *please note the slicer modifiers to make the bracket/screw part much strong I wanted a shelf that could specifically hold…
This is a small 2 part model to mount an Juniper ex2200-12C under a desk. This model utilizes screws to fixate the switch. The triangle part is just for easier mounting as the screws are already spaced correctly. As this is an under table…
This is my mounting solution for a generic pull-down projector screen of the type you'd find in any office supply store. Key objectives for the mount was that it had to blend in with the casing of the screen, allow the screen to be easily…
Inspired by the bracket models by @Jitti , these brackets allow for a LEGO train track to be mounted onto a ceiling, with enough strength and rigidity to permit a fully operational Lego train to run in a room suspended from the ceiling…
My buddy needed a light bar for his new Ender 3 V3. So I whipped something up quick. Requires 2 M3 bolts. Category: 3D Printer Accessories
Note: This will not fit the Plus model as its frame is differently sized. See my Ender-3 V3 Plus Collection . Revision and Additions: As reported to me the brackets were a little loose at the light end, so I've revised the models to make…
These and any length of 20x20mm square dowel will make an angled rack for your shoes (that you have too many of like me) Use simple countersunk wood screws no longer than 30mm to secure the wooden beams. I recommend using some foam…
Supercharge your tomato Yields in a growbag. increasing the number of roots on a tomato plant increases the size and number of tomatoes a plant can produce. remixed original to include a built in printable, modular, support cage that can…
Remix of the top bracket and the R bottom bracket for the Artillery Sidewinder X2 from dukedoks. I upload a L bottom bracket without logo too. Category: 3D Printer Parts
UM2 Clone brackets remixed for better fit Bosch Rexroth 2020 extrusion (6mm T-Slots and M6 screws for top and bottom brackets) with additional bracket for round rocker switch for power or LED on/off. I've also included Z-axis motor spacer…
If you need to make Ikea Bror shelving system higher than default 190 cm. You need another set of Ikea Bror legs, cut to the size, to put on top. If you want to make it much higher, it's best if you use second “X”-rod mounted to the top…
This type of mount allows you to attach your focuser motor directly to a tube. Designed for ~170mm tubes. This type of connection is extremely easy to print out of PETG and it's nearly indestructible. Clamping is done via M4 bolt, nut and…
2nd version of L and T brackets for LED strips with the width of 10mm. The version 2 Added holes for the covered LEDs, in the previous version the majority of the first LED was covered thus not being able to use the full potential of the…
![Keyboard Under Desk Holder/Mount/Brackets [Remix: 110mm Deep]](https://media.printables.com/media/prints/d5879759-5e2a-4e7a-8758-d2bff87538c3/images/12462529_009ecd6c-7142-49ff-8ce1-257711439e68_3b3472f5-26be-4592-8825-265d189c8d70/20260331_210155_caption.jpg)
