Counting matching models…
I used canopy model from GrabCad and tinkered simple mount for GPS. I used black PETG till layer 86, paused, changed filament to TPU, reduced temperature and printer the upper part with it. Came out nicely. But it can be fully printed…
I recommend using PETG to reduce the amount of vibration or hard TPU filament. you will need insert nuts with a diameter of 3-4mm and a length of 4-5mm for M2 screws. The camera is screwed to the model with 4 M2 screws 4-5mm long. The…
Prop guard for the GEPRC Cinelog 25 version 07 (recommended to use) thicker base wall and arms version 01 first version, bigger diameter (can be somehow tight to mount) Print Settings Printer: Anycubic Vyper Rafts: No Supports: Yes…
NEW Version: After crashing and breaking v1, I made a branched version similar to the original design but hopefully more robust. Let me know if it works out better for you! --- The GepRC Cinelog 20 prop guards are very fragile. I made a…
Hi everyone, it's been a few years since I bought a Cinelog35 V2 frame and I was trying to redraw it in case I needed to make a new part. The manufacturer didn't have a proper drawing of this frame, so I gave up for the sake of final…
Custom-fit protective case for the GEPRC Cinelog 30 v3 cinewhoop drone. Designed to store and transport your quad with antennas still attached and a battery mounted—no more bending antennas or removing your battery every time you pack up.…
Cinelog30 v3 GPS GEPRC M10 mount 25x25x8.2
Hey! GEPRC CineLog35 V2 GPS mount. GPS module is used Bainianxing-BU1025TF with UBX-M10050-KB + Flash Memory, supports GPS, Glonass, Galileo, BeiDou at same time. GPS module buy here edit 31.3.2023 v1.2 - added Walksnail and some minor…
Simple fixing of video antennas to avoid that with any collision or contact the antennas fold, since I realized that it is very easy and they go directly to the propellers, causing a major failure in that case, with this piece and two…
Model : This model fits the Cinelog25 v2. It is used to mount the DJI o4 Air Unit Pro. It is compatible with ND-Lenses. Print Instructions : Material: TPU, I used the Eryone TPU Filament Placement: Place the model on the bottom, just as…
Printed with PETG with .1 layer height. The MAG Alignment in Betaflight should be set to CW 90° in the config tab. But also confirm that the compass points the right direction in the setup tab.
Hey Pilots, this is a crazy little design. Why this? I Don't know. It adds about 2 grams on the weight and It Is useless but why not? I want to have legs of my Cinelog35 as brand new. Bumpers are suitable for Cinelog35 V1 or Cinelog35 V2!…
The other files I could find online didn't quite fot for me so I designed my own. These are designed for 3d printing, the solid outside rings print faster than holes in the side and only weigh ~3grams more per side while being stronger. I…
No supports needed. I printed with .08mm layer height on the X1C in PLA-CF and HTPA-CF. I will update with .4mm nozzle and .2mm layer heights in regular PLA. PA12-CF recommended for impact and crash resistance. DM me for improvement ideas.
Update 19.05.2024.: I upgraded the propeller guards further. Rigid on the inside and flexible on the outside. And 3 grams lighter! https://www.printables.com/model/884159-unbreakable-propeller-guard-for-cinewhoops-upgrade Update…
A clip that keeps your antennas securely in place on the GEPRC Cinelog 30 V3. Designed to prevent antennas from slipping into the props in the event of a crash. Print in PETG with 100% infill. I can't find the original source for this so…
Bottom plate of the CineLog 25 frame
GEPRC CineLog35 GPS mount. GPS module is used Bainianxing-BU1025TF with UBX-M10050-KB + Flash Memory, supports GPS, Glonass, Galileo, BeiDou at same time. GPS module buy here If you would like to support my designs to give me a small tip,…
12x12 mm Nano GPS mount to keep track of your flight safety, speed data, etc. It doesn't require long screws; you can use the original ones. It's installed under the antenna mount and is very lightweight.
A fast remix of Cinelog 30 prop guards, increasing central hole sizes for motor screws. I'm printing with PETG, the durability is nothing to write home about, but it protects the bystanders so there's that.
Geprc Cinelog35 Gopro mount
I created this model based on the CaddX Vista mount that came with the drone. The carbon plate for mounting GoPro is incompatible with the O4 Pro as far as I can tell due to the added height. No big deal as I intended to use the lack of a…
GoPro style mount for the Cinelog 35 (and other Cinelog frames)
A simple replacement for the GEPRC crossfire immortal T antenna holder. Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: No Supports: No Resolution: 200 Infill: 20 Filament: Saint Smart TPU Post-Printing ============= Category:…
A cameramount for the DJI O4 air unit pro on a Cinelog 25 V1 Frame. Long and short variant Adjustable angle of -2° to +25° Printable with little to no supports. For printdirection see picture. Honeycomb structure to reduce weight but…
I recently built my GEPRC Cinelog35 v2 when I noticed that the motors were touching the floor when I was setting the cinewhoop on the ground. I needed a solution for that problem. I have found a few designs, but none of which I was happy…
Summary replacement for the original one Print Settings Printer: Anycubic Vyper Supports: No Infill: 100 Filament brand: misc Filament material: TPU Everything gets better with coffee! https://ko-fi.com/pixbalance
RunCam Thumb Pro 4K CineLog25 V2 Direct Mount Features: Direct Mounting to the CineLog25/Cinelog25 V2, one part, nothing more Shock and vibration-absorbing geometry, enjoy jello-free footage Tight fit - good amount of friction to withhold…
Two designs one for GPS Matek M10Q and Crossfire antenna mount in the back. Important info about GPS! Mount it is made low profile so You'll need to unsolder bottom connectors and solder wires directly to GPS. Can also hold DJI O4 Pro…
print in tpu or petg - no support needed Category: 3D Printing
Hello everyone! Here are GPRC Cinelolog35 V2 designs for mounting antennas. edit 31.3.2023 v1.2 - added Walksnail and some minor aesthetic changes Print Settings Printer: whatever Rafts: Doesn't Matter Supports: Yes Resolution: 0,2…
GEPRC Cinelog 30 v3 gps mount 15x15mm
Cinelog35 bottom mount for gopro negative angle or reverse gopro shots. I have not tested this version, but it should work… nothing fancy, just a quick model
When ordering the analog version there is only one whole for the camera mount, which requires a new mount for the Walksnail system. This version can be used for the Moonlight, but also any other Walksnail camera with 2 mounting wholes.…
Ducts made of a single piece easy to print, use PETG layer height 0.2, print with the ducts up so that the motors sit well in the frame, printing supports are required
Replacement for the foam that comes with the GepRC cinelog25. Print in TPU with no supports No specific front or back, just print 4 of them and attach them to the prop guards. Attach with 3M double-sided tape, or the one that comes with…
CInelog 35 gps 22x22mm + long antenna mount, printed with TPU 95, 100% infill. There will be supports anyway, so just place it on the bed as better for your printer :)
A camera canopy 3D design to mount GoPro mount style instead of the default smaller mount type. I have 3D printed using TPU but can also be printed with hard materials like PLA/PETG. There is no need for support material.
Hello, It is a copy of the original canopy that I created with FreeCAD (the FreeCAD file is attached). But I designed a specific GPS holder for the Beitian Be-122 on the top instead of the camera mount. This must be printed in PLA with…
This is a special mount for TBS Crossfire Immortal T V2 FOXEER Lollipop 3 AXII antennas for the GEPRC CineLog 25 frame. VTX antenna brand/type doesn't matter; it works for any antenna with a connector up to the size of MMCX90. Two…
GPS Module for CineLog35 V2 HD O3 for GOKU GM10 module. FPV GPS This is the GPS MODULE: https://flywoo.net/products/goku-gm10-mini-v3-gps-w-compass
I ordered a cinelog 35 v2 and wanted to use a runcam thumb pro instead of a gopro, so I went looking for models, and found this one. I changed out the top mount for a smaller runcam mount, and it fits well. I printed the two parts in TPU,…
A mount for Naked GoPros on the Cinelog25
This model was originally created for milling and not for printing but you can try, maybe itll work out. It is based on original Cinelog25 top plate but Ive removed all unnecessary holes and made motor arms a little bit thicker.
Hey Makers, This little design add front and rear light for your Cinelog35 V1 or V2. Look at the wiring diagram in the picture. These lights use WS2812 RGB 3.5mm width LED strip divided into two parts - front and rear light connected to…
The original camera holder that comes with the frame was too big. So i made a smaller one for nano cameras like hdzero nano v3.
Print with TPU and tie a zip around the o4 Antennas if needed.
Cinelog 35 SMA antenna mount at 45 deg. No supports. TPU. 3 perimeter Print Settings Printer: Prusa Mini Rafts: No Supports: No Resolution: 0.15mm Infill: 15% triangle Filament: Any TPU Notes: 3 perimeter for a stiff print. 2 perimeters…
Simple GP Mount for the Geprc Cinelog35. Moves the camera forward to enable more angle and adds space for lipo.
I recently was preparing my Cinelog 35 v2 for a new FC, and I was upset about the capacitor placement blocking the battery wires from reaching the pads on the board. For this reason, I took measurements of the original TPU parts from the…
Paramètre d'impression: 50% en gyroide TPU 95A sainsmart/DFR pour moi le meilleur tpu
Gedruckt mit X1C Pla Carbon, bekommt ne schöne Matte oberfläche
Pad for the Cinelog25 V2. Made for use with M2 flat washer.
New propeller protectors that eliminate the need to dismantle the motors to replace them, lighter than the previous ones and easy to install and print, I recommend replacing the lower screws with ones with a slightly longer distance, and…
Print in ASA/ABS Weight: 4gm (2gm lighter than official duct)
Hey, little antenna mount for CineLog35 maybe for some other CineLogs, not tested for other models.. Print Settings Printer: whatever Rafts: Doesn't Matter Supports: Yes Resolution: 0,2 Infill: 20% Filament: whatever TPU whatever…
A simple naked gopro case for the GEPRC Cinelog 25. This is designed to fit in the original base that comes pre-installed with the Cinelog Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: Yes Resolution: 200…
When building the GEPRC CineLog35V2 FPV Drone, I was really disappointed that the Walksnail Moonlight VTX would fit, but I wouldn't have access to the MicroSD - furthermore, cables on the AiO board were touched by the VTX' metal casing.…
Better mount for gopro and dji action2 like cameras. Mount for GepRC Cinelog 35 Performance Print Settings Printer Brand: Creality Printer: Ender 3 Pro **Rafts:** No Supports: Yes **Resolution:** 0.22 Infill: 100 **Filament:** F3D TPU…
Inspired by serveral Designs. This is just a simple Go2 mount for my Cinelog25. May fit other models to, due to the simple fixing.
I didn't like the GepRc mount it didn't hold a nut. Required two tool. This is designed to hold the nut secure. Enjoy
I didnt found a holder for the Cinelog 30, so I made one by myself. Use Support for the back. The Text dont need any Support. Print with 0.4mm 15% gyroid infill and 4 Walls.
Support for Runcam Thumb Pro V2 camera
Cinelog35_GPS_ImmortalT - HGLRC GPS size: 20x18 mm version Cinelog35_GPS_ImmortalT_TBS - TBS GPS 20x22mm version GEP-M8U 22x22 version WS-M181 18x18 (Walksnail WS-M181) Category: R/C Vehicles
GEPRC GPS M10 DQ mount for GEPRC CINELOG30 v3 on front and back + box
If you're reading this, you probably broke your antenna in a cinelog, don't worry, I did it more than once too, so I created this 3D model especially to prevent it
I wanted to mount the LiPos on my Cinelog25v2 lengthways to the direction of travel, so I designed this mount. In my design, the LiPo pad is integrated into the mount. At the same time, the mount was reinforced so that it can be printed…
Mount for the Caddx Vista antenna to be fully protected on the cinelog 35 HD
I am not carrying a GoPro on my cinelog35-v2, Walksnail or DJI fpv cameras are good enough quality for me, thus I wanted to use the space for a protection bumper / canopy that might help the battery too in case of a crash. Havent crashed…
Der Batteriehalter wird an die originalen verschraubpunkte mit den Original schrauben befestigt. Mit dem Halter ist es möglich die Batterie in Flugrichtung anstatt quer zu montieren. Es gibt zwei STL dateien eine “Light Version” ca. 5g…
GepRc Cinelog20 bz121 GPS mount. TPU A95. Without supports.
90deg. shifted battery mount with custom tpu pads. You need some screws with a small head.
This is a remix of lachtan86's original dual antenna GPS mount modified to fit the Walksnail WS-M181 GPS Module
AirTag Mount for GEPRC Cinelog 20 HD
Support for the FPV camera of the GepRC CineLog 25 drone. I am using a Caddx Nebula Pro, but any micro-sized camera (19x19mm) could be used. The original support of the drone gave me jello and it was a very strange feeling with this I do…
This mount is designed specifically for Cinewhoop drones, tailored to fit the Cinelog35 V2 frame. It provides a secure and elegant solution for attaching both an analog VTX antenna and an ELRS antenna while maintaining a clean,…
adapted frame to fit the moonlight inside the cinelog 25v2 print ir in PLA with 4 Wall loop and 25/ infill
remixed from Seth Jordan's design on grabcad.
ELRS antena mount for my cinelog35 performance. There are two versions v1 horizontal mount v2. 25 deg. mount Category: R/C Vehicles
Cinelog35 Gopro 12 (9-12) Mount Angle = 15 ___ Cinelog35 Antenna Mount
This 3d print file is to rear mount a Runcam Thumb Pro action camera including a Vista Cherry antenna mount on a GEPRC Cinelog25. Recommendation Print both part in TPU and active support but exclude the support in the antenna mount tube.…
I was thinking about mounting my Walksnail WS-M181 GPS chip instead of the GoPro mount. This is the second version where the battery can't accidentially hit and destroy the GPS plug ;-)
I needed a new frame for my Cinelog35 v1 but i couldnt find it anywhere. I took the v2 and modified it so it can be used with the v1 camera subframe. I deleted the added holes in the frame, so its better suitable for 3D printing. Also i…
The camera soft-mounting on the Cinelog30 v3 is great for smooth cinematic footage, but any freestyle movements are likely to stretch the rubber grommets too much and put the camera mount in the path of the propellers. The propellers then…
I used canopy model from GrabCad and tinkered simple mount for GPS. I used black PETG till layer 86, paused, changed filament to TPU, reduced temperature and printer the upper part with it. Came out nicely. But it can be fully printed…
Printed with PETG with .1 layer height. The MAG Alignment in Betaflight should be set to CW 90° in the config tab. But also confirm that the compass points the right direction in the setup tab.
GEPRC GPS M10 DQ mount for GEPRC CINELOG30 v3 on front and back + box
A camera canopy 3D design to mount GoPro mount style instead of the default smaller mount type. I have 3D printed using TPU but can also be printed with hard materials like PLA/PETG. There is no need for support material.
A Camera Mount for DJI O4 AIR UNIT PRO Camera on a Cinelog35 Frame. printed in the right direction (see photo) supports are not needed. Parts printed in TPU95 Mounted to the frame with rubber puffers
The model can be used to pack the heavy DJI Osmo Action 4 onto the Gep Rc Cinelog 35 Drone. Or you can use the base to create more handy mounts. Required material: 2x | 3x10 Screws 4x | 3x16 Screws 4x | M3 Bolts Disclaimer! It is…
