Counting matching models…
ENGLISH … I want to share with you a 1:10 scale body model of the Land Rover 3 Series (III). The wheelbase is 229-230 mm. Body width 170mm. The front fenders, doors and rear fenders are connected using 3 pieces of carbon rods with a…
MN90/99 D90 Rear Roll Bar with and without tire carrier. You'll need to get quite a bit of support for this to all work; but it turned out really well. Both options are included in the file. You'll need 2 x M2 15mm or better to hold the…
As often in cheap crawler kits, the required steering parts for a proportional servo are not included. The suspension could be better as well. Ans of course, some tuning parts are always nice. So this thing includes: Servo clamp Improved…
WIP - MN90 D90 Front Battery Expansion ("frunk"). The stock part doesn't allow for any good size battery or after market electronics. So I created a set of 3 parts to make it all work. All holes (minus the M3 hole) are sized at 1.95mm so…
MN90/99 front chassis plate upgrade. No mods to the stock chassis rails are needed. Uses only 11 grams of plastic when printed at 0.2 and 20% infill. The stock screws for mounting the body can be used. This chassis plate requires a 17g or…
MN90/99 rear chassis plate upgrade. Uses 4 x M3 screws (8mm or 10mm will work). No mods to the stock chassis rails are needed. Uses only 11.4 grams of plastic when printed at 0.2 and 15% infill. The stock screws into the body posts…
die hinteren Fender angepasst. the rear fenders adjusted.
General Description Most parts marked L and R for left and right. LR parts fit or must fit both sides. However, some parts need to be mirrored in the slicer. Almost all holes are designed for M3 screws. Sometimes nuts are needed, but…
Reinforcement and Wheelholder for Tamiya Land Rover Defender D90. Replaces the polycarbonat pieces “rear brace A” and “rear brace B” (instructions page 15, step 30). Drill holes and use double-sided tape as described in the instructions.…
Rear Magnetic Body Mount kit with option for an extra enforcement. Allows for the rear body mounts to be magnetic only or use the stock screws into the existing supports. Does require you remove (if present) the one extra stand-off on the…
I have recreated the beautiful Porsche Design90 rims, also known as D90, for the modification of the low poly Porsche 991 Turbo. These fit the V2.1 tyres of the remix and are installed in the same way. Porsche Model:…
Additional Parts needed 1x Bahar Enclosure 150*140*70mm project box 1x C-Control Pro Nr. 197220 SD card module 1x MeanWell RS-15-5 PSU 1x CBM D9069 PetSD+ variant board ( https://github.com/InsaneDruid/CBM-D9096/ ) 2x 5mm LED (one red,…
I was trrying to found some models that would fit my car well but i didnt find any so i made my self one i am using 12V 10mm wide led stripe and some m3 screws for mounting I printed it in PLA but i would say you can print it with any…
Potřeboval jsem někam umístit jeden 5.65" displej, tak jsem pro něj vytvořil jednoduchý rámeček podobný tomu, co mám pro 4.2" modely. Seznam součástek: Good Display GDEP0565D90 5.65" 600x448 LaskaKit ESPink ESP32 e-Paper LaskaKit SHT40…
Engine bay for MN D90 with space for two 18650 Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 200 Infill: 38 Filament: PolyMaker PETG Category: Toys & Games
The battery door latch for the D50 D70 D70S D80 D90 D100 cameras can break causing the door to not properly latch shut. This is a 3D printable replacement part for the latch. Print Settings and Recommendations: 0.2mm Layer Height 100%…
this shroud is based on the rogue SD shroud. so it uses the same barrels. but I found that with short shrouds like this it's quite east to place your hand in the wrong place. so in case you like the look of a P90 ish style grip more then…
A couple of cases for the RFD900-UX so that you don't have stuff dangling around. Bonus cover included that I wasted time on trying to figure out how I could Light Pipe out the LED's... but one is behind the metal, so it's a big hassle. I…
Cheapo Well D90 full auto airsoft, fires when BB's get to the hopper. as standard this requires a lof of shaking in the air, dry fires are common. Reducing size of Mag and keeping BB's at rear improves feeding, makes gun more reliable,…
Small stand for a Cessna MD90 Clock. I painted mine glossy black, a barrel jack is used in the back for power, and wires are run through the base and legs.
A rear driveshaft for the FCX24M. I used a 4mm nozzle and PLA
A couple of cases for the RFD900-UX so that you don't have stuff dangling around. Bonus cover included that I wasted time on trying to figure out how I could Light Pipe out the LED's... but one is behind the metal, so it's a big hassle. I…
General Description Most parts marked L and R for left and right. LR parts fit or must fit both sides. However, some parts need to be mirrored in the slicer. Almost all holes are designed for M3 screws. Sometimes nuts are needed, but…
Cheapo Well D90 full auto airsoft, fires when BB's get to the hopper. as standard this requires a lof of shaking in the air, dry fires are common. Reducing size of Mag and keeping BB's at rear improves feeding, makes gun more reliable,…
I needed more desk space and thought of mounting topping D90 stack under the table like @lucasratmundo posted here https://www.thingiverse.com/thing:4731244 but his design needs a bigger printer and couldn't print it on Mk3s. So, i…
With this K1 exhaust fitting you can get your printer quite a near to wall and still get D90 exhaust hose out from it. I made this part on two pieces, because for easier printing. Just tape pieces together with ductape after printing, In…
The Zastone D9000 radio comes with a handheld microphone connected to the radio with an RJ45 cable. This is a desktop microphone that uses the PCB from the original microphone. There are two buttons, left and right, but only one of them…
Topping D90 / A90 Feet I wanted to increase the space between my Topping D90SE / A90D dac/amp stack as this gets very warm to the touch and the existing rubber feet are only 5mm tall. I also wanted space to run my headphone cable…
This piece is a replacement that I designed for a part of the battery that broke. It is the piece that is placed under the cymbals. You have to make two to connect it to the other. Printer: Ender 3 V2 Filament: Sunlu PLA Time: 40 minutes…
I wanted to print out Hadamard90's tulip but I wanted a flat base to make it more stable. I also designed a stem so I could place it in a vase with other flower and not have to worry about leaves breaking off. Filament for stem is Just…
