Counting matching models…
DHT11 Sensor Case for AZ-Delivery DHT11 Optional bottom piece with mounting hole included. The two pieces are meant to be clued together. I'm currently working on snap-together pieces. Feel free to remix. Tolerances for the top piece are…
This remix allows the use of sensors I purchased off Amazon (HiLetgo) that had a different style of connector from the sensor the original case was designed for.
Two part case for your cheap slim DHT22 board. You can find the matching DHT22 / AM2302 board all over the internet. Just make sure it looks the same - there are many different form factors floating around. Requires 4x M2.5x6mm screws 3x…
This is my rendition of a case with lid for the ESP32 S2 NodeMCU board to house the DHT11 temperature and humidity sensor. This model also have the Home Assistant logo embedded on the side. This simple design ensures a tight fit for the…
This is an enclosure for a DHT11 sensor module. The Sensor/PCB is held inside the case body by the post, and the lid is secured to the body using a flat or pan head M2x3 screw through the same post. Print Settings Printer Brand: Prusa…
Spliced together a few different files to fit my own requirements. You may need to re-size/check the carrier dimensions depending on your own ESP32 board. I designed this to use with Jumper cables, i didn't have a screw for the DHT sensor…
This custom-designed enclosure is tailored to house the Plantower PMS5003 Air Quality Sensor, along with an ESP32 NodeMCU and a DHT22 (or BME280 when using the alternative lid included in the files) temperature and humidity sensor…
DHT22 sensor outdoor box. The box is designed to prevent water ingress, allow air flow, and mitigate overheating by the sun. It also has a chimney to avoid the problem of condensation. This piece is still under test. 4 m3 screws are…
Simple DHT11 housing with 3mm cablehole. Lid snaps in place, no glue needed. Print instructions Category: Electronics Summary Simple DHT11 housing with 3mm cablehole. Lid snaps in place, no glue needed. Print Settings Printer Brand: Prusa…
Gehäuse für Wemos D1 mini oder andere ESP8266-Boards (Esp32, nodemcu ...) mit DHT22 / AM2302-Sensor. Case for Wemos D1 mini or other ESP8266 boards (Esp32, nodemcu ...) with DHT22/AM2302 Sensor. Print Settings Printer Brand: Creality…
This is my design for DHT22 sensor enclosure with 3pin JST-XH connector
What is this? This is an enclosure designed to house an ESP32 board (specifically, an ESP32 DevKit V1 board), a PMS5003 sensor, and a DHT22 temperature/humidity sensor. It's powered through the ESP32's micro USB port, which is exposed on…
This is my rendition of a case with lid for the ESP32 Devkit V1 NodeMCU board to house the DHT11 temperature and humidity sensor. This simple design ensures a tight fit for the ESP32 Devkit V1 board, and also a squeezed fit for the DHT11…
Summary A case for a temperature and humidity sensor powered by an Arduino uno board. The case fits: an Arduino uno a small breadboard a 16x2 LCD display a DHT11 temperature and humidity sensor The parts are locked in place by melting the…
I created a water meter sensor based on Lolin D1 mini v4 and induction probe LJ18A3-8Z/BX ( Build a cheap water usage sensor using ESPhome and a proximity sensor ). And I needed a box to house the D1 mini. Since it was already there, I…
Fixing the gap between the two components; now they fit tight together; Taking out the screw hole and replaced with a pin; New Air vents pattern This remix is used in my project here: https://www.thingiverse.com/thing:4352377 Enjoy!…
Case for dht22 on other sensor version outdoor with PG screw opening and cable stripe connector version indoor with backwall cable opening Used M2 8mm screws for lid M2x4x3,5 threaded inserts PG7 screw connection for outdoor version DHT22…
A case for Arudino DHT11 temperature and humidity sensor. The case is printed in two parts. No glue or screws needed. The chassi may have to be cleaned from any residual before inserting the cover. The case can be mounted with…
Here is a simple housing for the DHT11 temp and humidity sensor that is mountable using two #6 screws. Ideal for indoor applications or outdoor locations that are undercover as this is not a waterproof housing. Check out the assembly…
Print instructions Printer Brand: Pursa Printer: Pursa mini Rafts: No Supports: NO Resolution: 0.2mm
Housing for using a DHTXX sensor outside, keeping it shaded from the sun and weather. The housing has stacked "roofs" to allow for air to flow through but keeps water and sunlight out. It is a two part design for easy install and…
This little enclosure will hold an ESP32 and DHT22 snugly, for wifi climate monitoring in a nice small package. I recommend the vented, direct soldered lid. Even with the vents, if you use this without deep sleep or lower power mode, THE…
Republished from my thingiverse: https://www.thingiverse.com/thing:3342804 Links to the parts contain Banggood's affilate metadata. Intro I needed a PM2.5/PM10 sensor during this winter season. I wanted to monitor more than one room and…
A case for a humidity sensor system consisting of a DHT22 sensor, a Wemos D1 Mini, a 18650 battery holder and a battery charging module. Features: Sensor is thermally isolated from the rest of the electronics lid holds tight by press fit…
ESP01 + DHT modul case Print instructions Category: DIY Summary ESP01 + DHT modul case Print Settings Printer Brand: Creality Printer: Ender 3 Pro </div> Rafts: No Supports: Yes </div> Resolution: 0.16 Infill: 25% </div> Filament:…
This is my first attemp for a sensor case, which reads temperature, humidity and lux. It uses a d1mini flashed with Tasmota and a DHT22 and BH1750 (GY-302) as sensors. The data is published via MQTT to my HomeAssistant instance. This is a…
Enspired by the DHT22 Feather Enclosure created by cnf I decided to create my own. This model will enclose the Wemos D1 mini and a DHT22 sensor.
You can use this to make IoT devices , such as Tasmota devices or other IoT and Home Automations projects Hope this will help you
This enclosure is designed for the Waveshare ESP32-S3 Ethernet Development Board with PoE, used in combination with a DHT22 temperature and humidity sensor connected via cable. It includes dedicated cutouts for: The RJ45 Ethernet port A…
Temperature sensor DHT22 case
Snap fit for the screen and rear cover, M2 screws for the ESP32 board. Supports needed. Left and right side cable routing options. DHT22 → GPIO4 SDA → GPIO21 SCL → GPIO22
So I made this box that can hold in place an Arduino Uno, a breadboard, an LCD (16x2) and there is also room for a dht11 sensor on both sides to make it more convenient to assemble. The box was also designed keeping in mind room for…
ESP8266 and DHT12 Case
Simple case for an ESP8266 or ESP32 board (in my case NodeMCU), a temperature sensor DHT11 or DHT22 and a small SSD1306 oled screen. Works great as a small Duino-Coin IoT setup. Designed with Tinkercad. Parts need to be glued together…
Case for Esp32 + PIR + DHT11 + RCWL-016 I use Espresense to detect presence by detecting the Bluetooth signal intensity of my devices. Additionally, it has a temperature sensor and two motion sensors, one with infrared waves and the other…
This is a ventilated mounting bracket for a DHT22 Temperature+Humidity sensor, with an integrated connector that the DHT22 plugs into. It uses standard JST-XH 2.5mm crimp pins. You can find these at about any electronics supply house.…
Simple and small NodeMCU(ESP8266) and DHT22 case. 4x bolt m3x12mm The DHT22 is very close to the ESP. Create a code to put the ESP in “Sleep”. Then it will work fine!
Raspberry case for the sensor Category: Electronics
This is a remix I made to montior the temperature & humidity of my network cabinet using Home Assistant & ESP Home - It then triggers & automation to turn on fans to cool the cabient once a temperature threshold has been reached.
Case for DHT22 sensor Print Settings Rafts: No Supports: No Category: Electronics
The original version was designed with a small bar connecting the rounded slats. I have removed the bar and connected the slats with small connectors gto give them structure. Additionally I've added an opening for some cabeling. It's…
a small case for a ESP8266 D1 Mini with a DHT22 Shield Holes for wall mounting 4mm Dia
Dew Point Ventilation This is a case for another approach of dew point ventilation. Dew point ventilation means that you measure the temperature and humidity inside and outside. To decide whether ventilation is useful or not, you…
Einfaches Gehäuse für DHT11. Ichhabe es mit 0,15mm gedruckt, damit der umlaufende Snap-In gedruckt wird. (Im Slicer überprüfen, oder Kleber verwenden... :-) ) (DeepL) Simple housing for DHT11. I printed it with 0.15mm so that the…
Outdoor Case for Temperature and Humidity Sensor I'm working on a ventilation system , that needs to know the humidity outside the basement. Therefore we need this case for a temperature and humidity sensor. This case is intended for the…
Dear makers, we would like to share our ceiling case for DHT22 sensor, together with PIR Arduino compatible sensor HC-SR501. Use two 2x4mm screws for fixing PIR. Drill hole 67 mm. We tested with PETG due to higher temperature resistance…
This is a box for the DHT22 temperature and humidity sensor. it may fit the DHT11 also. i tested it for a week and i can say that this enclosure does not alter the sensor readings. You can find all my models here , thank you who will…
Wall thermometer with microcontroller ESP8266 and temperature and humidity sensor DHT22 inside the box and cable probe with Dallas sensor DS18B20. Both temperature sensors are optional and it is also possible to connect more cable probes.…
3D model on different extension for creation of cool things.
DHT22 / DHT11 / AM2302 sensor mount. Mount using zip tie or screws. Category: Electronics
This case supports a Raspberry Pi Pico W with a DHT22 in separate internal compartments. The DHT22 side has vents on the side and top to allow for airflow to enter the housing. I am using this with MQTT to HomeAssistant. I have the…
Simple sliding lid box that will hold the DHT11 temperature and humidity sensor securely with strain relief for the connector. There is a tabbed version for hanging and an untabbed version for sticking to things or just having a smaller…
DHT22 AM2302 Housing Honeycomb Style This is a housing in honeycomb style for DHT22/AM2302 sensors. Heat up the pin after putting in the sensor and push it down. Thank you to @TueftelTyp https://www.thingiverse.com/TueftelTyp/about for…
This is a case for the DHT-11 sensor which you can stick in the ground.
Changes in this remix: larger hole so that jumper wires fit through removed mounting hole split into two parts
Extended Base Plate This is a remix of the baseplate for the Outdoor DHT housing by llite . In my version, the cable doesn't leave the housing to the back, but to the bottom. Therefore I remodelled the baseplate in onshape (see link…
Desktop weather station based on NodeMCU ESP8266 (CH340), Waveshare DHT22 sensor and 1.3 OLED display. Designed with a dedicated storage compartment for a battery pack of your choice. For me it was a series connection of 3 AA batteries…
Simple remix to allow 1x3 DuPont connectors through the hole. The top available in the original model.
Simple DHT11/22 holder (stand). Print instructions Default settings will do.
ARCELI DHT11 Temperature & Humidity Module.STL
Needed a mount for my enclosure to hold the AM2302 (DHT22) temperature and humidity sensor. Didn't see ones I liked that allowed for easy mounting to the 2020 extrusion frame, so I made one. I have seen these boards from Keyes, DSD and…
Hier ein Remix von - Blinddeckel für Busch Jäger Reflex SI Abdeckrahmen von Ma Gu - um einen DHT22 zu montieren.
A quick design for an ESPHome Temperature Sensor. If the ESP board does not seat properly, make sure the edges are filed flush.
Simple case for DHT sensors. The ring can hold in place a mesh filter against dust. Print Settings Printer Brand: Prusa Printer: Prusa Mk2 Rafts: No Supports: No Resolution: 0.2 Infill: 20 Filament: prusament PET Notes: screw tolerance is…
A wallmount outdoor or indoor case for DHT sensors. The case is designed to wallmount, or even ceiling mount your DHT sensor more profesionally. It has a cover to protect the sensor from water and rain without affecting the readings. For…
DHT11 Sensor Enclosure A minimalist and compact enclosure for the popular DHT11 temperature and humidity sensor. Provides basic mechanical protection while allowing free airflow for accurate measurements. 🔧 Key Features and Uses:…
This little project displays the current humidity and temperature on a 5110-"Nokia" LCD. Additionally it records the temperature of the last 60 seconds, minutes and hours. Based on this data, a graph is drawn onto the lower half of the…
I designed this DHT22 Complete PCB housing snap enclosure as Thingiverse is having mainly the DHT11 smaller type and some DHT22 enclosure with exposed DIL pin. This is a Light and quick print. Only uses 1.89meter of filament and print…
Holder for D1 Mini with shield and LEDs. Optional separator that can be wrapped in Aluminium foil to provide additional shielding
This is case for Wemos D1 (ESP8266) and DHT22 based on 3D Printer Monitor for OctoPrint Wemos D1 ESP8266 case. Wemos D1 is running on ESPEasy firmware. Category: DIY
New version for less temperature difference due to ESP heating In this version a measure ca. 0.3°C difference between an open (breadboard) design and the D1 and the sensors in this housing. In the old version it was around +6°C delta.…
Terminal for SSD1306 0,96" Node MCU and DHT22. Desk thermostat and hygrometer.
Small outdoor mount for DHT11 temperature sensor. The sensor is to be held in place with double sided tape. I used transparent nail polish to waterproof the screws. Note: I have this mount outside exposed to the element for a year and the…
A quick Case for an ESP32 C3 and DHT-11 with an LED . Everything should just press fit in and together, tolerances are tight. If things are loose a little hot glue goes a long way. 05/12/25 - Tightened the tolerance on the lid, it should…
It's a small case/box for e.g. a DHT22 or DHT11 sensor. In a seperated compartment I placed a ESP01/DHT board with a small psu. There is a small area where you can tie wrap the incoming power cable. You get one of those ESP01(S) DHT…
I’m using the sensor in my Prusa XL enclosure. It’s controlled via the ESP32 camera . I soldered the wires on the camera side and routed them through the lower ventilation slots of Michael Fanta’s ESP camera case . Inside the sensor…
Simple snap together case for a Raspberry Pi Pico W with a DHT22 temperature and humidity sensor. I programmed the Pico via ESPHome to provide the temperature and humidity readings to my Home Assistant installation.…
weather resistant outdoor case for hdt22 temperature sensor. requires 3x m3 thread inserts. 3x M3*4 short screws * m3 hex screw barely fits to hold the sensor, smaller screws/smaller caps may be easier 2 mounts included and f3d file.
ESP8266 Rack - SSD1306 OLED Display - DHT22 temperature-humidity sensor
A small housing for DHT-22 sensors. Printed with PETG and 0.2mm layer in one piece. Needs no supports. Just put the top plate of the sensor into the small pocket inside the housing (may need some fiddling) and fix it all with a cable tie.…
This case is for the commercially available presoldered DHT22 sensors. You can find such sensors on AZDelivery. Sometimes they aren’t cut correctly (if you see a grooved white line on the edges); in that case they won’t fit. You can…
A box to mount an arduino featherboard with a DHT22 sensor to a wall. Still a work in progress, pictures will follow. Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: Doesn't Matter Supports: No Resolution: 0.2mm Filament: DAS…
Design to fit DHT22 module assembly produced by DSD Tech. Module can be found on amazon. Similar product may work. Base mounts to surface with single fasteners. All other components compress fit. I mounted this DHT22 print to my MK3S+…
This is a Wiha Glue-Gun Mount for the Skadis Pegboards. A little bit of a tight fit at the Pegboard, but it works.
Contains two DHT22 holders for use on a 3D printer cabinet. One holder has a cutout for a cable.
The DHT11 case is a compact and durable enclosure designed to protect the DHT11 sensor from physical damage and environmental factors while maintaining optimal functionality. The case includes strategically placed ventilation openings to…
Wemos D1 Mini and DHT22 Enclosuse with Neodym Magnetic
ESP-32S ESP-WROOM-32 PIR Dual relay DHT11 sensor case Category: DIY
Let me know if you also need other versions like a simplified version or with different pins (for example 90degree). Update: 2025-10-4 small fix in grid coutout dimensions
Really liked @drwatson6 design, changed it a bit to better suit my needs. Higher tolerance for component placement on PCB (i.e. compensating for poor soldering in the manufacturing) countersunk holes for wood screws stronger pins for…
A small enclosure to stand in the room to hold a 16x2 LCD a DHT11 and WEMOS D1 Mini in it. The right for size for a IOT infoscreen. Category: DIY
Das Sensorgehäuse wurde speziell für den DHT22 Temperatur- und Luftfeuchtigkeitssensor entwickelt und optimiert. Mit seinem durchdachten, passgenauen Design schützt es den Sensor zuverlässig vor mechanischen Belastungen und ermöglicht…
a small box with pin inside that effectively shields and holds a DHT22 temperature humidity sensor. Allows airflow in but not water. I had this set up as an outside air temp and hum sensor for my all sky camera. Printed with the solid…
Enclosure / Connector for a DHT22 / DHT11 / AM2302 sensor. Included are two different methods of interfacing with the sensor: CAT5 Ethernet Keystone Jack Cable Category: Electronics
A simple box for a NodeMCU and a DHT22 on a perf board. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: .28mm Infill: 20% Filament: Das Filament PLA mattschwarz Category: Electronics
Assembly Instructions All of the parts are shown above along with three dupont wires The top must be attached to the bottom case - I used super glue Once they are glued the sensor can be slid in The wires can be connected before or after…
You will need: DHT22 sensor ESP32 C3 Supermini 4 x 15mm M3 screw 4x M3 heat insert 2004A i2c lcd
