30 models
–- UPDATE -- This design has some issues with the spring geometry. The unit is not held in the ceiling with enough force, and mine have started to drop a little. Not awesome! There's a redesign on the way that will accommodate all…
Printable downlight fitting for a GU10 lamp. The springs holding it in place and the spring holding the lamp in the fitting needs to be taken from an old fitting. I used these to replace the fittings in the bathroom since these were…
This fixture can be used to surface mount the LIFX GU10 Downlight or other low-wattage GU10 LED lights. It's designed to fit a standard American 4-inch circular electrical junction box. The base can accommodate a standard GU10 socket…
Hood to mount most LEDs strips. The channel angled with a slight lip to prevent direct light shining outwards. Allows you to route between the Alpha on the left to the Bravo to the right. Included the one piece hoods and the 4 piece hoods…
Updated printable downlight fitting for an LED GU10 lamp. The springs holding it in place and the spring holding the lamp in the fitting needs to be taken from an old fitting. I used these to replace the fittings in the bathroom since…
I have a lot of Ultralux LLVP1242 downlights at home. Every month I have to replace at least one or two of them, and it's gotten quite expensive (at 12-15 euro each), so I decided to convert them to regular GU10 LED bulbs. This model…
I originally looked at the following model: https://www.printables.com/model/744002-8mm-led-strip-holder It looked like what I wanted, except it had holes. I tried to remix the print in Fusion and other packages, and found it was so full…
The 4" Gimbal Recessed RGBW Downlight This design makes it perfect for tight spaces and low voltage wiring makes it easy to put these in places that might not otherwise be well suited for traditional recessed lighting. Here's what you'll…
Downlight Glare Shield. The inner diameter of the shield measures 79mm. If you need a 64mm shield => 100 / 79 * 64 = 81.01 => Scale it to 81% Printed in PLA 3 Perimeters Feedback is welcome and I'm excited to see your prints. Happy…
This print is designed to turn a 6 inch Philips Hue downlight into a desktop accent light or hanging lamp. I'm unsure of the Euro sizes, but there's a chance this will fit one of them. You will need: 3xM4 heat inserts 3xM4x16mm screws…
I assume this could easily be used for fitting other 4" ceiling lights into an old 6" can space, but it was specifically designed for a Philips Hue Phoenix 4" downlight (older model, not the new “slim” ones). My light can has springs that…
This is a very simple L-shaped piece designed to mount a minimalist downward-facing light on the DJI Neo or Avata 2. Both drones struggle with confined spaces and low light, particularly the Neo. High quality Velcro is recomnmended to…
Printed in PLA black matte Layer 0.2mm Perimeter 3 Downlight Diameter 78mm Have fun printing and thanks in advance for your makes, likes, and feedback.
This is a easy to print full lamp, only things you will need is a 70mm downlight and glue. If printing the base and legs separate for dual color finish then the downlight springs will keep both parts together, if you want a permanent…
This is a simple non- destructive hanger that fits into an existing 90 - 95mm downlight recess, and incorporates a fitting to allow an IKEA HEMMA pendant fitting to bolt straight up. The fitting can then be adjusted to cover the downlight…
Design Concept: Decided a flashing or solid LED downlighting effect on the record would be fun while functional. Wanted to also make the design to be customizable with three parts Base, Cap and Emblem so that Makers could modify or design…
This is a support for fitting smaller downlights in a pre-existing hole, the insert is added to the upper side of the hole and is glued or taped in place, it allows plaster to be added in the gap between the existing ceiling and the part…
parts SLV DOWNUNDER OUT LED M M16 tubing for electric wires print settings Printed with Prusament PETG (white) because it's suitable for outdoor use.
Only for LEDlight. Makes a downlight for 72mm hole fit in a 140mm hole. Not for lightsources that becomes hot. Follow instructions for the lightsource, consult electritian before install. If not used properly it can cause fire, explotion,…
I made a new downlight cover for my SLV Myra Wall downlights I use at my garage. I wanted to have more surrounding light and a nice modern light effect to look on when walking towards my garage. As you can see on the shop pic of this…
Wer Kennt das Problem nicht. Das Alte 12V Halogen Leuchtmittel ist defekt, und das neue LED Leuchtmittel pass zwar in die Fassung aber es lässt sich nicht im Downlight fixieren. Hier habe ich einen passenden Adapter. Die Verwendung ist…
IKEA Tradfri GU10 bulbs have a rounded bottom. This ring supports them in the EvoFire frame. There are two models. I've printed these in ASA to give improved temperature resistance. they are probably fine in PETG depending how hot the…
I assume this could easily be used for fitting other 4" ceiling lights into an old 6" can space, but it was specifically designed for a Philips Hue Phoenix 4" downlight (older model, not the new “slim” ones). My light can has springs that…
Great way to stylise and change the colour of downlights without replacing the whole light. To fit 48mm ID and 88mm OD, 3mm deep.
I saw these dust bowls in hardware stores and thought I would try to make one using TPU. It worked brilliantly. My first try was a bit too high to work very well so I reduced the height a bit, but included both versions. This would depend…
The LED spotlight in my kitchen broke and in order to have light by taking advantage of ones with a smaller diameter that I had at home while I processed the guarantee of the original, I designed this adapter. It is designed for a hole of…
Attach with double sided tape to the horizontal protrusion, reuse the stock springs for tension mounting, use threaded inserts (~5.4mm OD for M4) and bolts (either 4 short ones or 2 long ones) to fix the springs. The springs are spaced…
This is made with PLA 20% fill and with support and upside down. This fits Namron Alfa Reflector warmdim art no: 3234654 can use petg. but the best is self-extinguishing plastic. :)
The firefly downlight Functional, minimalist and modern downlight meant to be hung on the bottom of a cabinet or similar. Designed with kitchen use in mind but can be used wherever you like. The design is free and open source, easily…
Lightweight but sturdy bracket for temporarily hanging canless downlights until you get your ceiling hung. Tested and fit several different brands of 6" (nominal) lights. Inner diameter is 160mm
