Counting matching models…
Materiał z którego zalecam wykonanie to PETG, dla lepszej wytrzymałości Ociekacz na sztućce, o wymiarach. Jeśli ktoś potrzebuję mniejszego polecam po prostu przeskalować na wymiar jaki komu pasuje w slicerze drukarki. Pozdrawiam. Wysokość…
My little Bottle drainer. Fits different bottle sizes like wine bottles and SodaStar/SodaStream bottles. Added 4 little holes on the bottom for some little rubber pads (7mm). Printed in Marble PLA, 0.2mm layer height, no supports. Added…
This dual purpose bottle holder will allow you to ‘compact’ your sauce/dressing, with cap in place, before application to your food, when the bottle contents are virtually consumed through repeated shaking of the bottle. Using this tool…
A remix of the excellent resin tank drainer by @K9DefenseTech_8289 . It holds the SL1S resin tank vertically with a slight forward tilt, so that the resin flows smoothly along one corner into a container below. I wanted one to fit a…
cutlery holder for drying cutlery. print with the holes facing up . pleas note there is also a file for feet that keep the holder off the work top, cloth etc. also there are holes in the bace for alawing water to drain out. i recomend…
A part to connect two bottles together to drain one into the other. Internal threads provide a secure connection. The part has an internal funnel, so make sure you connect it the correct way for optimal draining. Prints without supports.…
Noticed glass straws were left in cups and in the sink where other items got put on top of them. As you can imagine with glass, this can lead to broken straws, which could lead to cut hands, which could lead to sepsis, then antibiotic…
Designed this scrub-daddy holder to rest on the metal wire drainer of my kitchen sink. Can also be used to hold other scrubbers/sponges of a similar size. The design features: Rounded design to suit a normal scrub daddy, with a fair bit…
You know that moment after your coffee? You’re happy, energized, ready to conquer the world… then you remove the capsule and it starts peeing water everywhere . You throw it in the sink to let it drain? Too bad you also use the sink to…
I recently upgraded my ZD-915 de-soldering station. The little DC-DC converter PCB was left over. Instead of sending it to recycling, I soldered on 2 more resistors and modeled this little part so I can safely use it to drain capacitors…
Chtěl jsem odkapavač - jak pro talíře, tak i pro příbory. Soubor "bok" si vytiskněte 2x - z toho jednou zrcadlově převrácen - bohužel otvor na svislé opoře pro talíř není vycentrován. Soubor "spojka" také vytiskněte 2x. Pro spojení - jsem…
Keep your cutlery clean, dry, and hygienic with this smart drainer. Thanks to the dual-bottom design, water drips down into a lower reservoir, so your utensils never sit in it 👍 No more stagnant water, no more mess — just simple and…
This plant water collector and drainer is designed to make watering easier, cleaner, and better for the plant. The main part of the design is a wide, circular tray that sits beneath a flowerpot. When the plant is watered, any extra water…
Fully Customizable 3D-Printable Soap Box with snap-on lid This 3D-printable soap-box features a snap-on lid and adjustable tolerance for easy fitting. Ideal for kitchens and bathrooms . The built-in drainer keeps your soap dry, making it…
I created this lawn drainer to avoid too much mud in my garden. when you fill it with sand, water gets down ! As one can see in the picture, place them every 15cm Model designed with opens cad. Feel free to ask for it so you can adapt it…
This Dish Rack Drip Tray Holder is a 3D-printable replacement part designed to fit the bottom tray of dish racks. It collects and directs excess water from dishes into the tray, preventing spillage. A durable solution for replacing the…
These parts print in small 8.5" sections that after put together you must weld together any way you like that is waterproof. I recommend printing at 100% infill for a better waterproof seal.
Das Model von MichaelW257 hat mir schon gut gefallen. Ich habe diese Designidee für eine 2er Variante verwendet, das Modell jedoch komplett neu aufgebaut.
voici un égouttoir que j'ai designé en 2 pièces chaque pièce comporte des trous d'évacuation sur le bas permettant une évacuation relativement aisé de l'eau lors du séchage des ustensiles de sorte que l'égouttoir en lui même doit être…
Drainer for water bottles, glasses, cup, Etc. Prints without supports or brim.
These are an easy printable angled build plate suspension and a resin vat drainer for the Anycubic Photon Mono X 6K. Both are printable without supports on an FDM-printer or the Mono X 6K. The resin vat drainer is designed to be used…
This is a remix of the original side drainer provided by HeyGears. With the original model, you'll have to use two M4x12 screws in order to secure it to the build plate. There are also other solutions out there to hang the buildplate at…
HOW TO PRINT: 1. For the base, smaller layer lines / more quality means better water flow . Or you can rotate for the model to stand upward with supports for the smoothest flow but i have not tried that. I changed to Gyroid infill due to…
A sleek and practical cutlery drainer designed for efficient drying of your utensils. Compact yet spacious, it ensures water drains effectively while keeping your cutlery organized and easy to access. The original files are provided so…
I was sick of having cutlery soaking in water so I made this riser. It's meant to work with ORDNING Stainless Steel Cutlery Stand and the EKIPERA plate. It prevents drying cutlery to come into contact with excess drain water. Edit feb…
needed a stable and solid way to keep my vat while i cleaned and filtered the resin. wasn't sold on any that currently populate the market. so I mades my own. works with this lab stand from vevor . definitely others. which uses M6x1…
A holder for your Scrub Daddy that will drain into the sink. Gap from the edge of my sink to the wall is 5 13/16 inches or roughly 147mm so it should work for anything that size or smaller
// deutsche Beschreibung ganz unten You can customise this draining rack as you wish : choose the size/length of the rack individually and the spacing between the individual elements This ensures that everything you put down to dry after…
Materiał z którego zalecam wykonanie to PETG, dla lepszej wytrzymałości Ociekacz na sztućce, o wymiarach. Jeśli ktoś potrzebuję mniejszego polecam po prostu przeskalować na wymiar jaki komu pasuje w slicerze drukarki. Pozdrawiam. Wysokość…
It's just a small cup drainer to leave next to the sink or inside a bigger dish drainer. Not parametric, but it shouldn't be difficult to edit the Fusion 360 model to make it a different size or to modify the hole pattern.
Notice water coming through hatch after a wash? Corrosion in trunk? This piece can fix the common issue where the hatch drain tube grommet rips off and allows the tube to fall inside the hatch. This then prevents draining and causes water…
Dish drainer holder to be glued under the kitchen counter. Using a hot melt gun will not damage the line board. Thank you for the feedback.🧡
Este es un escurre‐cubiertos diseñado para impresión 3D, con varias cestas que cuentan con un patrón calado repetido en sus paredes. Dicho patrón permite un rápido drenaje del agua y aporta un toque estético. Las cestas pequeña y la…
I designed this drainer since I didnt wanted any of the existing ones out there. This one is very simple any easy to clean. There is also an insert that the cutlery wont stand in the water. I printed it in PLA but I dont think it does…
A basic box with a 5° angle at the bottom. Very effective, but a bit ugly. But effective … Photos soon, i have left those to my mother ;-)
My little Bottle drainer. Fits different bottle sizes like wine bottles and SodaStar/SodaStream bottles. Added 4 little holes on the bottom for some little rubber pads (7mm). Printed in Marble PLA, 0.2mm layer height, no supports. Added…
My reccomended print settings: PLA or PETG 4 perimeters 7 top solid layers basic support needed (look at the picture) Suggestion: glue a self-adhesive rubber pads on the bottom
Foldable bottle holder, suitable for bottles with a neck internal diameter of at least 16 mm. When folded, the object measures approximately 15 x 13 x 1.6 cm It prints without supports and it is useful to use a bit of superglue to join…
You wash your cutlery by hand but you use a glass jar to dry them or you dry them by hand ! Why not try a stylish, efficient cutlery drainer designed in France ? Easy to clean and repair with its 4 removable compartments. Drips flow…
Got a Baby? Those bottles are in constant use! With the MrConcept Baby Bottle Drainer you can dry them in Style. It will also work with your bike bottles and even with half litre aluminium bottles. But be aware: Nothing stops those drips…
This is a cutlery drainer designed to hang from a (max) 6.5 mm wire or part of a dish rack (such as in the photos) and drip into a tray underneath. The main, larger compartment measures 190 x 160 x 71 mm , fitting for tablespoons and…
I wanted to design something to stop my reusable drink bottles from falling over after washing them and leaving them to drain upside down
The drainer is in 3 parts so it can be washed easily. You can also adapt the bar to what you want to dry by printing different models. I made a 200mm high bar to dry a bottle. The hole is 21mm in diameter and the bar is 20.8mm so the…
This Model was remixed from the original designer @sciartist_1982253 . This remix was made so you can close the lid while you let the resin drip. This way one can leave without having to worry about any particles falling into the Resin.…
Previously had troubles with warping on the AAA battery cover on a different model, saw this remix and liked it but the tolerances on the battery cover were way too loose. I re-adjusted the tolerance and added a little notch so that the…
What? • Put this e.g. in your yogurt for an hour and water will accumulate in it ↦ makes it more creamy as strained yogurt (Greek: strangistó giaoúrti Turkey: Süzme Yoğurt ). • Or to filter .. the thread is a PCO-28 (standard PET bottle…
Panier égouttoir couverts avec poignée dimensions 19cmX12 4 compartiments Cutlery drainer basket with handle size 19cmX12 4 compartments
Egouttoir à vaisselle 40cmX40cm extensible jusque 65cm de long avec support de tasses ou bouteilles démontable et grand égouttoir à couverts 40cmX40cm dish drainer, extendable to 65cm long, with removable cup or bottle holder and large…
Sodastream bottle dryer, they can be connected thanks to special wedges. If you want to sell my project write to me privately. It should be printed on the side Print settings: Layer height: 0,2mm infill: 5% Material: PET-G Supports: NO
Useless thing to drain last drops of shampoo bottle to another one. Print Settings Printer Brand: Anycubic Printer: All-metal Mega **Rafts:** No Supports: No **Resolution:** 0,12-0,2 Infill: 15 **Filament:** - PLA Category: Bathroom
Suitable for sponges with these dimensions: b=55mm l =90mm h=25mm Printer: Prusa Mk3s+ Supports: YES Resolution: 0.2 Infill: 20% Gyroid Notes: printed in Renkforce Silver PLA
This Soap / Sponge Drainer is part of the 15 Minute Designs series – functional prints designed in 15 minutes that make everyday life easier! Designed to sit over your sink edge, it allows water to drip directly into the basin, keeping…
🟢 FREE 3D Print: Cup / Mug Drainer Design Series: 15 Minute Designs — #1 Category: Kitchen Utility Estimated Print Time: ~1 hour Designer: 3DPDP License: Free to download, remix, and share (Non-commercial) 🧠 About the Design This compact…
Ustensil drainer basket, printed with Anycubic ABS like PRO2 Note the published model doesn’t have the gap at the bottom. Here the Onshape link :…
This stylish drainer for glasses and mugs combines practicality with modern design. It features four interchangeable pads offering different shapes – circles, hexagons, rhombuses, and waves. Each pattern not only aesthetically enhances…
Ho eliminato il fondo del raccoglitore d'acqua x evitare se si accumuli nel suo interno ,cosi l'acqua scola direttamente nel lavello .
A set with three parts: a draining base, a cutlery holder, and a top separator.
This stylish drainer for glasses and mugs combines practicality with modern design. It features three interchangeable pads offering different shapes – circles, hexagons and rhombuses. Each pattern not only aesthetically enhances the space…
This dual purpose bottle holder will allow you to ‘compact’ your sauce/dressing, with cap in place, before application to your food, when the bottle contents are virtually consumed through repeated shaking of the bottle. Using this tool…
2 versions in a single model, just split the object in your slicer and pick the one you need. The one with a cutout is better for lower cabinets. Bottom is 8cm x 8cm, top 9cm x 9cm. 15cm height.
A simple, no-frills 3D-printed stand that holds laundry detergent bottles at an angle to reduce waste—easy to design, fast to print, and solves a common everyday problem with minimal material.
Drainer for ALL detergent cup to prevent the sticky buildup from forming in the cap. This threads on in place of the vent cap. and prints as 3 parts, the support blocks have a ~.1 mm gap between them and the actual object, use variable…
Intro: i got inspiration at print from Maciey, but i needed different properties. so i have created my own model (Blender file attached) Characteristics: inner area: all edges rounded, including inner bottom corners ! → ✅ easy cleaning…
A stand (in various sizes) to get everything from a bottle, each file has a measurement in mm that should be the size of the bottle top you want to drain, needs some support for the funnel section.
You probably hate when your soap bar goes soggy underneath… well this is your solution!!! This holds a soap bar smaller than 70mm X 100mm. Enjoy!!!
This is a simple 1 part print that has a big impact on YOUR life. This fits a soap bottle smaller than 80mm X 60mm ENJOY!!!
Egouttoir à bouteille diametre 30mm, très stable, fonctionne parfaitement sur les bouteilles en métal, Impression de préférence en PETG
These feet can be pushed on or glued on existing thin feet. The thin foot on the drainer is 1.8mm. A brim or raft may be needed to support the thin strip feet on the built plate. I used a PEI with no problem. I used generic PLA, 0.20…
We have a fancy detached drainer on our sink which, through operator error is often moved to a point where the drainage outlet isn't. This simple spout fits underneath and directs draining water back into the sink. Printed in PETG with an…
A remix of the excellent resin tank drainer by @K9DefenseTech_8289 . It holds the SL1S resin tank vertically with a slight forward tilt, so that the resin flows smoothly along one corner into a container below. I wanted one to fit a…
Sponge drainer holder (PARAMETRIC): F3D (parametric file): sponge holder v4.f3d instructions one the pictures with FUSION 360 STEP: sponge holder v4.step STL files: D20_W75_L102mm pipe ø 20 mm D21_W75_L102mm pipe ø 21 mm D22_W75_L102mm…
Dishes drainer with honeycomb patern Print in 2 pieces. Connect with 4 M3 hex srew and heat inserts. Hole for inserts: 3,9 mm diameter. 4 mm deep. keep this in mind to choose right inserts. Drainer dimention : 200x200 mm Have water drain…
This is a remix of https://www.printables.com/model/435267-prusa-sl1s-tank-drainer to make it fit metric 2020 extrusions instead of the original imperial 1010 extrusion. Everything else is unmodified.
I've been using this toothbrush holder for several years, I've just modified it a bit. The water can run off and the toothbrush dries. easily accessible perfect angle for drying easy to clean hygienic (no undercuts or sharp edges) You can…
sponge drainer for the kitchen is a practical and aesthetic gadget that makes it easier to store a sponge by the sink. Thanks to special holes in the structure, it allows water to drain freely, which prevents moisture accumulation and the…
Égouttoir à imprimer de préférence en PETG À poser directement sur l'évier, à coller ou visser au mur ou accrocher sur une barre de 5 mm max La goutte est à imprimer en deux couleurs et à coller. Respectez la positions des .STL sur le…
This model was just designed in Onshape and has not been printed yet (because I don't have a printer). I would really appreciate it if you print it and give me criteria and I will change it and update to what you ask.
I love my Kalita Wave 185. I do not, however, love leaving wet grounds in the basket, nor do I like dumping wet grounds straight into my compost bin. Enter this drainer. This can be placed over a 3.5" (90 mm) prep dish, allowing the…
FR (English below) Égouttoir à couverts, organiseur de bureau ou de salle de bain ou ce que vous voulez sauf un bocal à anchois. Pas de colle, pas de supports excepté pour les quatre petits pieds (moins d'un gramme pour les quatre pieds).…
This adapter allows you to get every last drop of resin out of your cartridges. To use it let your cartridge sit at an angle to let all the left over resin flow to the top of the cartridge, then use a knife or saw to cut the lower corner…
cutlery holder for drying cutlery. print with the holes facing up . pleas note there is also a file for feet that keep the holder off the work top, cloth etc. also there are holes in the bace for alawing water to drain out. i recomend…
I recommend that you print two of these to give the drainer a stable base.
A part to connect two bottles together to drain one into the other. Internal threads provide a secure connection. The part has an internal funnel, so make sure you connect it the correct way for optimal draining. Prints without supports.…
In case your kitchen sink drain board has a flat surface, you can use this fast printing drainer base for bottles, etc. important print settings: Top Layers = 0 Bottom Layers = 0 Infill Density = 20% Infill Pattern = Triangels Print…
Cutting board rack/drainer Made with angle guide under to install it onto square kind of kitchen sinks. Print in vertical position without supports:
If you've got the Sterlite Dish Drainer with the 25-ishmm round feet on the base, these should slip right over. Useful for helping the water drain or to make up for an unlevel surface. Print settings really shouldn't matter, I just used…
Ikea Dish Drainer footpeg for rising the drainer. By rising the drainer prevent the rust accumulation when touching the sink. The footpeg has holes too to drain the water outside. Maybe it works with other dish drainer´s.
