Counting matching models…
The Sunlu S1 and eSun eBox unfortunately don't come with a built-in humidity gauge. But there are cheap mini digital hygrometer/thermometers available in many shops which allows you to easily add one yourself. My design consists of a base…
I was fed up with the Velcro-mounted window seals made of fabric. Firstly, the Velcro gets loose when the window heats up in the sun, and secondly, it wasn’t easy to mount and was never securely mounted. I use a portable air conditioner…
Printing Instructions Filament Material Advised PETG/PET/ASA Material Propaties Required Property Type Constancy Hard Durablity Not brittle Sun Bleaching Protection depends on use case but would advise for long term use not using PLA Heat…
Overview Filament dryers have exit ports in less than ideal places. The filament often has to bend sharply to line up with the port, which is exaggerated depending on hoe much filamnt is left on the spool. This simple design prints in…
I printed with ABS at .2 layer height. I used 55% infill, but you could go 100% for more strength. The threads are clipped square on the factory part, probably to ease release from the injection mold. It’s an unnecessary detail, however,…
note 11th April - Significant improvemtne to grippiness! I accidentally had an older version of the legs - if you downloaded it, get the new version here. 📌 TL;DR: Your Bowden tube gets slowly pushed into the dryer during printing. This…
Remixed to fit OEM MIKA3D Cardboard Spools. Size is 195mm
An overengineered replacement for the easily broken handle on many Whirlpool and Maytag dryers (https://www.whirlpoolparts.com/PartDetail/Door-Handle/W10861225/4380739). PETG is recommended. Supports are not needed. You will also need…
I completely remodeled this part. I made it so it would accommodate the 10mm pneumatic fitting without the need to drill. Also when i printed the original one the insert came out and the nut was loose so re-worked tolerances It needs a…
Boot dryers. Fits 7530 blower fans. Ball bearing / 24v type recommended. • I used these: https://www.aliexpress.com/item/1807313991.html • Angled slots on back and bottom to assist with airflow coverage. • Measures ~165 x 142mm • Print…
Držák pro uhlíkové filtry pro sušičky BEKO. Filtr jde koupit třeba v Bauhau... u digestoří.
Warning: Work In Progress! This project is still fairly early and may experience significant changes. Feedback welcome. Printing 3 shells, top & bottom layers @ 15% infill should be fine PLA, ABS+, PETG, etc should all be fine. ABS will…
Fits fine printed at 0.2mm Structural speed with PETG, upped the perimeters until no infill.
A RFID holder for Snapmaker U1 that positions RFID tag, at original spool position, when using external filament feeders or dry boxes. Since Snapmaker spools have two RFID tags, one can be carefully removed, and added to printed part. I…
--- If you like this project, please consider leaving a tip --- EDIT 2019/09/01: I believe that nylon and polypropylene is a material that can be used for the springs. Since not everyone is able to print nylon or PP on their printers, I…
Improved belt pulley for AEG dryers with two 608 ball bearings. Printed with ASA CF and 50% infill. The new original replacement part seized up on the shaft after a short time, so I designed a version with better bearing support. Two 608…
Smart household appliances tend to be short-lived due to the added complexity creating more points of failure. If you must have some smartness in your appliances, it's sometimes a good idea to add it on as a separate system. This solution…
Is your 3D print space cramped and disorganized like mine? Does your filament dryer have a narrow exit angle for filament to feed nicely? Hang one or more of these sliding weights from your filament until it comes out at a better angle.…
Laundry dryer - outdoor - spacer for holder (filler for 40 mm diameter pipe)
Fits hairdryers that take 64mm diameter adapters
I designed this magnetic brush holder because I found the original placement of the brush very impractical For this, I used 8x3 mm magnets. In theory, you can also simply leave the holder on the brush and reattach it right after use. I…
I created this because the creality space pi filament dryer does not come with a proper ptfe tube connector. this replaces the rubber grip that comes with it. Parts needed: 2x M3 screws of any length (i used m3 x 14) 2x M3 nuts 1x ptfe…
Držák pro uhlíkové filtry pro sušičky BEKO. Filtr jde koupit třeba v Bauhau... u digestoří.
Fits hairdryers that take 64mm diameter adapters
Snapmaker U1 Full side Dryers system Hi gang :) So here is my crazy invention/addons for a pair of dryers to keep filaments under dry control and to help also cooling down the drivers and PSU as modification to the existing intake ports…
Improved belt pulley for AEG dryers with two 608 ball bearings. Printed with ASA CF and 50% infill. The new original replacement part seized up on the shaft after a short time, so I designed a version with better bearing support. Two 608…
In Japan, you peel the labels off plastic bottles, let them dry, and take them to the designated recycling area. We have a lot of plastic bottles at home, so my wife had a hard time drying them. We tried drying them with different sizes…
Small hanger for electrowarm shoe dryers. 3.6 mm screw diameter
Snapmaker U1 Full side Dryers system Hi gang :) So here is my crazy invention/addons for a pair of dryers to keep filaments under dry control and to help also cooling down the drivers and PSU as modification to the existing intake ports…
I have a couple Creality Dryers including the Space Pi X4. I found that the bowden tube connection to the dryer likes to get pulled into the dryer. A lot of users in the community buy air fittings which is a costly solution. Print this…
so i live in an apartment where its hard to find somewhere to dry my clothes, designed these dryers and they have been doing there job since. Print instructions best printed with a material that could withstand heat, pla will deform in no…
original has the Dryer at an angle, but was having spools falling forward and jamming, this remix holds the dryer flat removing this issue.
Parametric Quick-Dry Glass Joint Adapter for Hair Dryers Introducing a game-changing accessory for all glass enthusiasts! This parametric model seamlessly attaches to your hair dryer at one end and a glass joint at the other, enabling…
