Counting matching models…
Wall Mount Quick fastening system for panels and coverings - Sistema universale di Fissaggio rapido a Pressione Available in two models: Wms_1 - Wms_3 Filaments: PETG - PLA+ - ASA - ABS Hardware needed: Screws as per assembly requirements…
BOM Item Qty M3x5x4 Heatset Insert 4 M3x8 SHCS 6 M3x20 Standoff 2
A Guide for a Hand powered metric external thread tapping with a metric standard tap holder. Works well on soft metal rods such as aluminium, copper and brass. Tougher metals will produce swarf that will quickly wear out the bearings even…
Plastic Rivets created for Mazda M6. Diameter 17.8 / 6 mm, depth 17.4 mm
A calibration fastening for caliper for bed leveling. All you need is one print and two M3 bolts to tighten the caliper. The hole size for caliper is 17mm width and 3.9mm thickness. I printed it in the wrong way so I had to use it on the…
Tired of having to pick up the top panel of my Castorama Neva fence from the ground after every windstorm, I made this clip. Made to fit on Neva aluminium posts (7 cm square) from Castorama. Need supports to be printed, preferably with…
Fastening support for Ericsson SPO 14xx service module card. Print instructions Print Settings Printer Brand: Prusa Printer: i3 MK3 Supports: No Filament: Filament PM PET-G Resolution: 0.15mm Infill: 30%
This is the Stemfie3D wrench tool for nuts and screws.
As with everyone with a little bit older Japanese car, the fastener for the hood support was broken on my 2006 X-Trail T30. So why not model it and make a print? This part is not 100% same as the original. I placed the V-shaped clip on…
I developed a new base for den Sunlu S2 filament dryer. The reasons were that I wanted to fix the device (in my case to a windowsill) and that I wanted to have ventilation at the bottom of the fan so that the moist air can get out of the…
Fastening spanner for the RJ45C-L4SAS connector which is used on the Advanced Navigation GNSS compass. Depedning on your printers tollerance you may need to file the knurling sligtly, it is desinged to be a loose-ish fit to prevent over…
Here are some Kederhooks. If you are camping you will need them to better attach your awning or tent to the caravan. See attached pictures.
AC/DC 220v-18V power supply in a case with a mount for a Makita 18V BL1860B battery. The power supply was designed for a Chinese-made electric trimmer (fake STIHL) with a mount for a Makita battery. Electronic components: 1. Switching…
Print out of 98a tpu 40-50% cubic infill. 100% for jump pad base. will need two of these if printing parts for my handlebar mod https://www.amazon.ca/dp/B09LYX22WF?ref=ppx_yo2ov_dt_b_fed_asin_title ALL files seen in pictures included.…
Fastening button for trailer nets or trailer tarpaulin. DIN 912 M4x12 mm with washer and hex-stop-nut Print Settings Printer Brand: Anycubic Printer: i3 Mega **Rafts:** No Supports: No **Resolution:** 0,2 Infill: 20% **Filament:**…
Fastening Clip for Ford Transit MK3 (Up to 1991) – Universal Use This model represents a fastening clip/retaining rivet, primarily designed for the Ford Transit MK3 (up to 1991) and used for the upper plastic near the windshield. However,…
Pin for Fastening Clips – Ford Transit MK3 (Up to 1991) – Universal Use This model represents a pin designed for fastening clips, modeled after the original part used on the Ford Transit MK3 (up to 1991) . It is specifically designed to…
This Remix of the SBK Screwdriver Holder replaces the magnet mount with a tapered hole that accommodates most common construction screws; including Drywall, Chipboard, Woodworking, Metal self tapping, drywall anchors and Concrete Screws…
This fastening clip is made as a replacement part for the original FLUKE clip which is breaking apart after a few years. Works with FLUKE 289 multimeter and others. If you have a different model or need any changes please let me know.…
When I was assembling my new MK4S, I wanted to fit the X-axis stepper motor guard from my MK3S+. I was a little surprised when I realized that this guard doesn't really fit. After measuring carefully, I realized that the rear metal plate…
Czech: Android vs. Apple zapínání kabátu Tištěno z FLEX 98A English: Android vs. Apple fastening coat Print of LFEX98A
I increased the hole diameter to 3.3 mm and designed a square and hex nut insert so that the screw fastens into the nut instead of the plastic. Another benefit is the elimination of the possibility of breaking the shaft along the layers…
Wall Mount Quick fastening system for panels and coverings - Sistema universale di Fissaggio rapido a Pressione Available in two models: Wms_1 - Wms_3 Filaments: PETG - PLA+ - ASA - ABS Hardware needed: Screws as per assembly requirements…
Wall Mount - Side fastening system with security clip - Sistema di aggancio laterale per pannelli Recommended Filaments: PETG - PLA+ - ASA - ABS Hardware needed: Screws as per assembly requirements All our designs are free to download and…
Install it in place with original clips and then rotate 90* and screw original Grohe holder.
Vacuum cleaner pipe spare part, developed by myself, positive testing, PETG spare part
It is made in Fusion 360. I made it myself for a fence, because buying such elements is expensive. The diameter of the fence wire is 2mm. I printed this element with an Anycubis Cobra 2 pro with PETG filament.
Passt auf Bestway Steel Pro Frame Pools oder andere Hersteller mit gleichen Stangendurchmesser. Die Klemme hat einen Innendurchmesser von 32,8mm. Ich habe es in ABS gedruckt Bei gefallen lasst mir doch gerne ein Like, Make oder Kommentar…
I found it really too long to make knots to attach the spring protection foam on my daughter’s trampoline.
This is a wall spacer for the skadis board. It is self-fastening (uses a modified t-clip) and holds the board 20mm from the wall (matches the skadis mounts).
This part replaces the top part of a mudguard holder on some models of Gazelle (children) bikes. I hope this helps for someone. This is only the upper part. The part most likely to break. Included is the Fusion360 archive to help you get…
A mount to attach the original spool-holder to the top of the printer.
Magnetic holder for securing a greenhouse door. You will need four round magnets with a diameter of 12 mm and a thickness of 2.7 mm (e.g. from Aliexpress). Since neodymium magnets cannot withstand rain and moisture, I wrapped them in…
English version: Suitable for tarpaulins with eyelets that have an inner diameter of 12 mm or 1/2 inch. The thread is M12 x 1.75 and has enough play. Use a 4x40mm wood screw for the central hole – this allows you to screw the bottom part…
I misplaced the blade fastening screw for my Chef's Choice 615 Electric Meat Slicer. I made a replacement part to match based on measurements (I did not have the original part to compare to). So this is not a 100% exact match but it…
Fastening for lamella
Plant fastening / fixing clips - Pflanzen Befestigungsclips 30mm / 40mm variants
"Securing the path to world domination!" Complete the penultimate phase of your Technodrome factory display with Robot #6: The Riveter . Featured in the background of the iconic "Enter the Shredder" manufacturing montage, this unit is one…
BOM Item Qty M3x5x4 Heatset Insert 4 M3x8 SHCS 6 M3x20 Standoff 2
A Guide for a Hand powered metric external thread tapping with a metric standard tap holder. Works well on soft metal rods such as aluminium, copper and brass. Tougher metals will produce swarf that will quickly wear out the bearings even…
Plastic Rivets created for Mazda M6. Diameter 17.8 / 6 mm, depth 17.4 mm
A calibration fastening for caliper for bed leveling. All you need is one print and two M3 bolts to tighten the caliper. The hole size for caliper is 17mm width and 3.9mm thickness. I printed it in the wrong way so I had to use it on the…
The holes have a diameter of 3.5 mm. 12 mm wide Velcro strips can be used. 45% infill No printing support required.
Tired of having to pick up the top panel of my Castorama Neva fence from the ground after every windstorm, I made this clip. Made to fit on Neva aluminium posts (7 cm square) from Castorama. Need supports to be printed, preferably with…
This print should take at least less than half an hour to print both the screw and bumper. Feel free to modify the models to suit the needs of your car model.
english 9 July 2026 UPDATE: It has become apparent that, whilst the thicker wall thickness does increase the stability of the wide boxes (100 mm and above), it is unfortunately still not sufficient to prevent the box wall from giving way…
A simple case for the SkyDrop vario. The case is attached to the harness with cable ties. Can be printed without support, use a brim.
Garden fastening nails for garden fleece. You need to print horizontally, with supports, then the nail will be stronger Supports: Yes Resolution: 0.2 Infill: 100 Filament: ASA, PETG
The mounting of this bracket is achieved by clip-fastening! The development of this camera mount was inspired by various mounts that can be found on Thingiverse. As it is, none of them was exactly what I had in mind. That's why I decided…
I ran out of these clips so made a printable version. It's parametric so if your tubing is different or can't get the same size nails you can change it. Freecad source attached. (modify the spreadsheet values). The original had the nail…
Hooks under trunk door on car or minivan and provides hole for paracord. Should work for most vehicles. Originally designed to secure back of canoe to top of vehicle. Parameterized Open SCAD file provided for fine tuning or extending the…
Printed this for fasten our groceries in car so that bags won't fall down. You can easily use this for almost everything else too of course. Because I don't have scale to measure the breaking point I tried to breake this with my bare…
The mounting is done by clipping in the bracket and can be moved forward or backward if necessary ... I thought I could print the bracket I had designed for the Prusa MK3s. It fits too, but very tight, so it is very difficult to move.…
(German below) English: Because I didn't like to screw or glue our new room ceilig, I wanted to attach our smoke alarm onto our nice Paulmann URail lightsystem Trails. For an easy attachment I used the genius but simple hookpart from…
Fastening support for Ericsson SPO 14xx service module card. Print instructions Print Settings Printer Brand: Prusa Printer: i3 MK3 Supports: No Filament: Filament PM PET-G Resolution: 0.15mm Infill: 30%
1, I have bought this one https://www.autokelly.cz/Product/RO-C70310/12586260 It could be also printable, but I think that this is mechanically better. I do not know, may be from PETG or somerhing like this. 2, I have made mother screw…
One of the best-selling and popular topcases for bikers is the "M-Wave" brand, also sold under several other names like "Point". It is being held shut with clamps that can snap and break if your bike is falling down (e.g. someone pushes…
Width/Length: 50mm Thickness: 24mm Angles: 90° and 45° Print Settings Printer: GEEETech Prusa I3 Pro B Rafts: No Supports: No Resolution: 0.2 mm Infill: 20% honey comb Category: Household
Update 18/09/2023 Added “HSW Single Wall 11x2 SD” & “HSW Single Wall 11x3 SD” Update 30/04/2023 "HSW Single Wall - 11x7 HD" added “HSW Test Wall HD” added All files renamed ---------------- My new Honeycomb Coffee Wall just needs one…
The Cap on the End of the fastening for the Fiamma Bike Rack. Use ASA / PC or any UV and temperature stable filament.
La sujección de los cables de la cama caliente de la Kingroon KP3S no es que sea muy buena que digamos. The fixing of the cables of the heated bed of the Kingroon KP3S is not very good to say. Está sujeta por sólo una brida, con lo que…
DE: Hierbei handelt es sich um eine Befestigungsplatte um an einer Gabione eine Steckdose/Schalter oder ähnliches zu befestigen. Im FreeCAD können die Abstände der Bohrlöcher und die Freiräume für das Gabionengitter sehr leicht angepasst…
Bmw E30 - center side bar cover fastening (for OEM: 51 43 1 933 731, 51 43 1 933 732). Base dimensions copied from the original part (fastening). More durable\thicker model - to prevent future broking. I recommend to give a little sanding…
English: I used the model for the mount of the 4028 fan, but find it inconvenient that the Fanblates are unsecured. A second issue is the mount in combination of a EBB42. It's not enough space for the Hot-Endcables, so i make it a little…
A Remix of KRIVOBRK 's excellent Backpack Hook for the IKEA SKADIS pegboard. Utilises Line Arc Line's SKADIS T-Clip System for fastening, specifically capze's “mini” variant of the T-Clip which can be found here:…
Fastening Cap / Filter Lock for Kärcher WD3 vacuum. Replacement for Kärcher's original product number: 4.075-012.0 This model consist of 2 parts: a base and a plug. Print both and screw them together to complete assembly. No supports are…
Mounting on profile sheet C-18. Fastened with screws M 4x50 - 4 pieces. Cable entry in corrugated pipe 25 mm
The needle like structure found on the back of the GLM 80 broke i decided to make a 3d printed part of it. although I did print on a 0.6 nozzle, going with a smaller nozzle can help. printed on PLA. The part is of similar size and works…
Those who want to winterize their pool or basically just want to stretch a tarp over the pool have certainly already looked for a solution to fix the tarp. These reliable fastening hooks are attached to the vertical bars of the pool with…
The model is the OnGuard U-Lock (sold with a cable) with the following dimensions: 115mm x 230mm x 13mm. Retrieve the bolts and rubber from the broken part and install it on the new one. Screw the system. That's it ! You can see my…
Curtain Wire Fastening (see pictures) screw an M3*10 into the hole in the bottom of the fastening and thru the round wire case
Replacement part for Meta Quest 2. Print in any filament you got (preferably PETG) with 100% infill.
I created this handle because I was tired of having to use a hex wrench every time I had to adjust the laser head height
Print the bottom part oriented how it is with a brim and a pause at layer height to embed an M4 nut into your print to lock the 608 bearing into place with the 608 washer and then clamp the hose style clamp over the 608 bearing and lock…
As a firefighter, i use this with my equipment to hold doors open for the firehose. I simply knot a string inside the hole and fix it with a carabiner on my Jacket. Dimensions: length = 80mm width = 30 mm angle = 15° The angle is on both…
This is the Stemfie3D wrench tool for nuts and screws.
It is a fastening knob for wolfcraft dowelling jig part number 4650000. One of mine broken, then model and replace with printed one. Print Settings Printer Brand: Prusa Printer: MINI Rafts: No Supports: No Resolution: 0.15 mm Infill: 90%…
Follow the orientation explicit on the preview image. Use this product to reduce friction: https://s.click.aliexpress.com/e/_Dl9aZJ1 Needs 19mm furniture pads.
This cable grommet fits a 1in drilled hole and will accommodate a thickness of a couple mm. I created it to use with a fogger system I'm building that is part of mushroom grow tent. This grommet allows the power cable for the fogger to…
This fastening knob is made for the Logitech Shifter for the G920 wheel and various others. I designed it because I often move the setup between tables and getting a good tight grip on the table was always harder with the shifter compared…
Pencil box holder for Honeycomb storage wall second version
Just a little bracket to fasten a round cross piece to a rectangular cross-section stretcher under an antique bench.
Ich fand die originalen item Tischplattenbefestigung 0.0.617.63, für die 8 Nut, einfach zu teuer, für das was diese Befestigung bei mir leisten muss. Diese Befestigung ist für 40x40 / 40x80 ..... gedacht. Ich hoffe ihr könnt was damit…
gestern habe ich die Tischplattenbefestigung 40x40 (item 0.0.617.63) für die 8 Nut, hochgeladen. Da ich auch 30x30 Profile habe, aber von item da nichts da ist, gleich mal auch dafür eine erstellt. Ich hoffe ihr könnt was damit…
