Counting matching models…
About This design is heavily influenced by the design by Weedhaze , but my own. Each organizer holds one Fireboard Competition or ambient temp probe . It is designed to securely but not overly tightly hold onto the probe and wire. It also…
Fireboard Competition Probe Holders Donations: paypal.me/weidhase ***UPDATE: New model for long comp probe with new plug- can cable storage. Provided STL files are for your personal use only. - the „normal“ versions have a cavity to hold…
A quick remix of @SoloTSi97's excellent FireBoard 2 Minimalist Case, with hood and small internal mangets. I sometimes run long cooks and although the FireBoard 2 is “weather resistant," I wanted to add a hood to keep rain and direct sun…
A minimalist case for the FireBoard 2. Printed at 100% scale, this case fits snugly around my FB2. There is also a lid available here: https://www.prusaprinters.org/prints/46462-lid-for-fireboard-2-minimalist-case Three versions are…
The Fireboard smart thermometers are a fantastic way to monitor and control your grill or smoker over WiFi. This stand is taller and steeper than the magnetic base accessory so it holds the monitor at a better viewing angle and keeps the…
I made a simple shroud for the FireBoard 2 unit on my LSG Lone Star Grillz Pellet grill to protect it from sun & rain. Recommended PETG or higher temp resistant materials. The holes for the magnets are sized at 15mm x 4mm (two 2mm thick…
Print the backplate with the fireboard opening down and your choice of supports(I used tree). Print the faceplate with magnet holes up, no supports needed. Recommended to print with ABS or PETG since this will be outside. Requires…
This is a lid that works with my FireBoard 2 Minimalist Case: https://www.prusaprinters.org/prints/46461-fireboard-2-minimalist-case The lid just fits onto the case by friction fit, so how tightly (or not) it fits will depend in your…
Rain/snow cap for fireboard drive blower
The cover I have built is a three part print. I used black PETG for the sides/top and frame. I used clear PETG for the front. I did not use any supports and printed with a .20mm quality. For the frame, there are 7 cut outs for some bar…
This is a plastic expansion around FireBoard2 device which lets you to store your probes untangled next to the FireBoard2 controller. Apply two rubber bands around the frame to fix the wires. The 4 middle holes are designed for the grill…
This is a stand I made for my Fireboard device. I wanted it up off the smoker table at a good viewing angle, with room to plug in the sensors. It fits nicely around the device, holding it in place snuggly. I'v been using it now for a…
Information about the model This adapter allows you to mount the Fireboard Drive 2 Fan to a Broil King Keg 5000. It replaces the bottom daisy wheel dampener. For obvious reasons you need to use a plastic that has a good Heat Deflection…
Print mounts with M4 nuts embedded in part: Pause print at last layer full hex is visible in slicer preview and insert nuts into print, then resume print. Used M4 x 8mm SS screws with M4 fender washers and then 1/4" Fender washers to…
I replaced my (horrible) BBQ Guru UltraQ with a Fireboard 2 Drive. The one thing the BBQ Guru does better was that it came with a pretty decent mount/stand while the Fireboard 2 the mount is extra. Rather than printing an entire new stand…
I present to you a handy storage case to protect your Fireboard Spark when not in use. This case does not require any supports and uses 8ea. 6mm x 2mm neodymium magnets to keep the case shut. I suggest using PETG, however PLA or any other…
First design to mount the minimalist case to the masterbuilt opening.
I upgraded my Masterbuilt XT with the Fireboard 2 Pro. The unit worked wonderfully but didn't have a clean way to mount it. I designed this to fix that.I haven't tested to determine if heat is going to be an issue. Since I keep my smoker…
An alternative to the official Fireboard Nozzle Adaptor. This connects directly to the Fireboard Drive Blower's outer flange, securing it in place with its rails. I used a short piece of ¾" copper pipe I had lying around along with a…
This is a custom mount for the Masterbuilt Gravity XT that lets you install a FireBoard controller using the original Masterbuilt controller shell and factory mounting brackets. The goal is a clean, factory-looking setup without permanent…
This holder replaces my old Char-griller Gravity 980 Controller. I used CNC Kitchen M5 Threaded inserts. The holes line up with the original holes in the smoker for the controller. I mounted it with M5 x 10mm button head screws. I printed…
The Fireboard Drive blower is designed for sliding door vents, which the Oklahoma Joe's Bronco doesn't have. This adapter connects the blower to the Bronco's circular air intake tube, letting you run the Drive for automated temperature…
FireBoard Drive 2 Masterbuilt Gravity 800 Grill Mounting Bracket: Optimized Printing: Splits into three distinct pieces to eliminate the need for awkward supports and ensure ideal print strength. Easy Alignment: Integrated alignment pins…
The compatibility list on the FireBoard site makes it clear that the OKJ pellet smokers are not the best fit for the Pellet Drive even though many use the same standard main components as brands FireBoard does support. The main issue is…
I upgraded my Masterbuilt XT with the Fireboard 2 Pro. The unit worked wonderfully but didn't have a clean way to mount it. I designed this to fix that.I haven't tested to determine if heat is going to be an issue. Since I keep my smoker…
