Counting matching models…
This is an easy install paddle modification for both the FlyDiGi Vader 3 and 4 Pro gaming controller. This is a drop in replacement for the rear buttons on controller. Simply remove the 4 screws from the rear of the controller, pry the…
Got tired of seeing that empty mount at the top of the controller. If printed with recommended settings, it is thin enough to not interfere with charging cables, at the very least with the cable included with the controller. Recommended…
Minimal single-piece 3D-printable stand for Flydigi Vader 4 Pro. Should fit other gamepad models as well. Print without supports Layer height 0.12–0.20 mm
The default color scheme of the Vader 3 Pro looked extremely tacky to me but I didn't want to paint the original parts. I instead designed 3D printed parts for the colored bits and a back cover, so I can pick any color I want. I designed…
This adapter was designed to connect my phone to my Flydigi Vader 4 pro gamepad, and it will also fit other Flydigi Vader/Apex models that have a standard mounting connector. To build it, you will need: 1. Print out 5 parts from this…
Alternative, more traditional, D-pad for the Flydigi Apex 4. Probably also fits the Vader 4 Pro.
Simple back cover for the Flydigi Vader 3 Pro. Included a portless version for a cleaner look, it's easily removable anyway. Made it so it's a snug fit so it can be printed without the rails. PLA 0.20mm layer height 10% infill no supports
Print it with precision settings with layer height as small as possible. My print: Layer height: 0,10mm Infill: 100% Supports/brim: no
This is the second version (remix) of my Flydigi Vader 4 pro gamepad adapter. For convenience, a standard 1/4 clip can be installed on the gamepad, since in most cases standard clips of this type are used. The platform for vertical…
Printed it with tree supports on a side and it came out quite well Note: On photo is the old version that wasn't fitting for Vader. STL is a second and updated version with Vader support
Same as the original, just the screw config has been changed
The original model fits Flydigi controllers perfectly but the mount on the back is not compatible with 3rd party Skadis boards like the Keepo. I switched it to a quad formation which will fit most Skadis type boards
Print Notes PLA tested Best result: ~45° tilt, thumb surface facing down Supports recommended (improves concave surface feel) No-support print is possible but rougher Fit / Use Designed for press fit (mention if tight/loose after you…
Flydigi Apex 4 Controller Stand (No Supports, Optimized for 3D Printing) This is a custom-designed stand made specifically for the Flydigi Apex 4 controller. The geometry was carefully measured and modeled to ensure a precise and stable…
Flydigi Apex 4 Controller Stand (No Supports, Optimized for 3D Printing) This is a custom-designed stand made specifically for the Flydigi Apex 4 controller. The geometry was carefully measured and modeled to ensure a precise and stable…
Used basic photogrametry to get a bit more accurate shape of the controller in order to make a snug fit for the holder. Just print it in whatever color you want using 0,28mm layer height, use 3,5mm screws for the wall mount, slide the…
Pla 0.2 mm layer height 3 walls Manual support for connector Enable support>set to manual> support painting>Fill mode>click on the bottom of pushfit connector I'm using with Moderate Weight-Bearing Snap.
Lock the tension rings gamepad Flydigi Vader 4 Pro When I play the tension ring keeps moving so I created a component to lock it in place. Instructions: _Need double-sided adhesive to stick it to the handle. _Stick it to the position…
I was paranoid about losing the USB dongle for my controller when it wasn't in use, so I made a simple mount that fits in the slots of the cell phone holder. There are some other versions out there, but I wanted one that was a little more…
My coworker wanted a strain relief for his controller that would hold his thick usb c cable. I printed mine with the large flat angled bottom plate touching build plate with supports for the inner overhang, but if you aren't as worried…
Flydigi Vader 4 Pro Dock Auto-Centering Insert Unfortunately, Flydigi’s official dock does not auto-center the controller — not sure why, but it’s pretty frustrating. So I fixed that. Variations Smaller variation that requires glue Self…
Old project, no guarantees. Used this to attach a phone mount to the controller. Use supports when printing the gopro adapter. Print in given orientation.
Печать производить из гибких смол. Не печатайте из обычной смолы. Abs-like v3 - минимум. К примеру, детали печатались из ABS-like 3.0 от Anycubic и Conjure Rigid от ChiTu Systems . Печатать можно на столе или в воздухе, используя…
Печать производить из гибких смол. Не печатайте из обычной смолы. Abs-like v3 - минимум. К примеру, печатались кольца из ABS-like 3.0 от Anycubic, а шест из Conjure Rigid от ChiTu Systems. Печатать можно на столе или в воздухе, используя…
Technical Details & Printing Recommendations: Material: I highly recommend using PETG or ABS/ASA for this part. Given that these buttons are subject to constant clicking and physical stress, PLA might be too brittle and prone to snapping.…
