1,106 models
This 19 inch 1U rackmount for the HP Elitedesk mini series is perfect for homelab enthousiasts that want 1 or more HP 1 liter pc's and rack mount them. The mount consists of two printed parts that both can be printed without supports by…
This should support basically every HP ProDesk and EliteDesk mini PC I could find pictures of. It also has mount holes to work mounted forward or backward in the rack. The rack I'm using it with is…
Requires:Original G305 PCB, Scroll, Side Buttons and Screws. Requires 4* 5mm Diameter 3mm Depth magnets. Requires 4* 5mm Diameter 3mm Depth magnets. (may need glue) rotate top -55 degrees, rotate Rear 90 degrees. If you enjoy this mouse…
FINALLY FINISHED I've tested the final version of this mouse for a couple months now and I'm convinced it is pretty much as good as it will get. Enjoy! Background Story This Model was initially made for school and then continued in my…
Full instruction writeup on instructables: https://www.instructables.com/Razer-Viper-Mini-Wireless-Mod-G305/ It will likely ask you if the baseplate file should be separated, it should not be. I can no longer combine the bodies in Fusion…
This is a Model of the HK G36 in order to transform the Lucky and Dummy 13 actionfigure into a soldier. Check my profile, there will be a post with all of my parts for the actionfigures.
For PERSONAL USE ! If you want to sell my models as 3d prints > 7$ commercial license >>> PATREON update-cable 17cm
Should be compatible with Logitech Headsets G230, G231, G332, G430, G432, G930 but only G332 was tested, and works perfectly. I used Prusa Mini+ with Prusament PLA and default “0.10mm DETAIL” settings in PrusaSlicer. Original author:…
LogitechG305 Mod compilation. You will find everything you need to fully modify your G305 and tinker with it to your hearts content… or maybe just create your own mods :D Update 2022.7.6 : Added more mods including an insane 20-30gr mod…
Print with the flat part of the grip on the print bed with supports. I used a threshold angle of 10 degrees with snug supports! Feel free to get this directly from me here: https://dildesigns3d.etsy.com
A 1U bracket to mount an HP EliteDesk 800 G3 , G4, or G5 in a 10-inch rack I designed and printed the Skeleten , a 10-inch rack to house my homelab. I wanted it to contain everything I needed, except maybe a NAS. From top to bottom: 2U -…
I designed this because the existing models on the internet were either paid or not well made. It fits snugly and does not slide off. The current version turned out to be slightly smaller than expected, but it still fits my (average size)…
The middle part needs support on build plate only, the other parts shouldn't need any supports. Uses m4 machine screws and nuts to assemble after printing. buymeacoffee.com/dlford
I wanted some better ergonomics while I played my games. I remixed the grips from STR to fit the RG35XX. It's a snug fit. Printed in PLA with supports on build plate.
just another gardena coupler Use clearcoat to get a waterproof coupler.
Thingiverse https://www.thingiverse.com/thing:5577372 Remixed from https://www.thingiverse.com/thing:4808386. The original model worked, but the corners made it uncomfortable for me to use. I tightened up the fitment to the mag, added a…
G36 speedloader created from several 3D models- combining expierience into a speedloader who can load 10 bullets who are on factory rail and inserting induvidual bullets (5 in short version or 10 in long version). Simple model to make…
The Anbernic RG35XX H is a retro handheld emulation game console that runs on Linux. It's design and shape allows for a case that be used on the front or back of the device, allowing the case to be used as a grip case or a protective…
Cooling Base for the GMKtec G3 Plus Mini-PC I designed this, completely toolless cooling base, to increase air-flow through the mini pc via an auxiliary 120mm PC case fan. I used a spare Arctic P12 connected to a USB adapter. Added…
An upgrade to Monorim MX0 to allow stable rides without wobbles way beyond the 100kmh barrier. Needs sheetmetal manufact
I was looking for a stable desk mount for my Unifi G3 instant cameras that could be elevated more than the existing models I found. After printing the nanoHD DeskStand from BradleyB, I was impressed with the stability and desided to remix…
This was made with an SFX power supply and AMD RX5700XT in mind. I highly recommend you use a gpu “blower” style cooler as it will be much easier to cool. During assembly, make sure the PSU fan is facing the outside, otherwise it will not…
IF YOU NEED THE EPIC ULTRA FOR THE "RG351MP" ( Metal Plus) FOLLOW THIS LINK!!!: https://www.printables.com/model/240177-anbernic-rg351mp-game-pad-epic-ultra Please respect the Licence the thing comes with! Thanks Thanks to Thingiverse…
Additional caps for the Redgrass Games 360° V2 ergonomic handle for miniature painting. Easy to print. ---28.Jan.2021--- ADD: bow option support for Rathcore V3 system ---21.Oct.2020--- ADD: tall version bigfoot version stand foot Print…
-58g with holes / 63g without holes. Weight will vary based on battery and print material. -Wireless using G305 Internals -Rechargable AAA via magnetic microusb tip -Designed for FDM printing -No soldering required FREE THINGIVERSE TEST…
One more for the CSHMFSEU (Clockspring3D/Hot Makes/Filament Stories Extended Universe)! Presenting an ambulance remix of the awesome Hot Makes/Filament Stories Flippy Ladder Firetruck to complete the first responders set. Original…
Mounting base model for Unifi Protect G3 Instant camera. Can be added to your custom mount to give you a single piece solution to meet your needs. Print instructions Category: Camera Summary Mounting base model for Unifi Protect G3…
I used canopy model from GrabCad and tinkered simple mount for GPS. I used black PETG till layer 86, paused, changed filament to TPU, reduced temperature and printer the upper part with it. Came out nicely. But it can be fully printed…
Print this with the top side of the clip down. I printed with supports with a 10% support angle threshold. You shouldn't need a brim depending on your plate, but I printed previous versions with a brim just to be sure! Feel free to get…
The bracket features 2x 4mm mounting holes for screws to mount the bracket to a wall. There’s a hole underneath the camera for a standard ¼” screw to mount the camera to the bracket. The bracket has a slot in the bottom for the USB-C cable.
Every firetruck needs a police car buddy so I designed this remix of the awesome Hot Makes/Filament Stories Flippy Ladder Firetruck by Clockspring3D. Prints on its side without support just like the original. Original Clockspring3D Flippy…
Remixed from: https://www.thingiverse.com/thing:4600978 https://www.thingiverse.com/thing:3823244 https://www.thingiverse.com/thing:3969266 I used the tinfoil and lithium battery for a big while and I was looking into making a battery…
For best results I recommend Resin printing. I included an example model of how I Resin printed this on a Anycubic Photon Mono X using Anycubic standard Black Resin. 2 Layers of dark gray spray-paint (I ran out of black spray-paint). 2…
This is a 1:29 scale drawn from an equipment diagram and reference phots found on the Interwebs. Optimized for FDM printing. Tub split in half is for less than 240mm bed (Ender 3) You will need: 3mm sheet of plastic, wood, metal cut to…
In collaboration with HyperPlay RPG , I have designed a grip for the RG35XX H games console. Print with supports 15% infill 0.2 mm layer height See HyperPlay RGP's review of the grip here: I also sell this on my website and Etsy store ,…
Hello there, Couldn't find any SL-8 / SL-9 Stock conversion for my G36 GBBR build, so here is my G36's Project - Futuristic CQB/DMR Conversion set. Should fit on most G36s, but built on WE G39 999c IdZ GBB. Won't fit JG's G36 (JG6…
I have had success FDM printing this model. Mods I did to the Logitech g305: Replaced the AA battery with a AAA battery and spring. SLA printed back cover Weight 79g total with the SLA print coming in at 3g compared to the stock 7g back…
The Ubiquiti G3 Instant has a small base and is easily knocked over. Simply setting it on a shelf doesn't allow and vertical adjustment. This stand is a little more stable than simply setting it on a surface and allows full articulation…
Combined can holder and hook for attaching to steering shaft. M3x5 screws + nuts used.
Update03: Added Bracket for heat inserts M3x4x5mm. Update02: Added bottom hook for U-LOCK - ULTRA COMBO 245/153C. Update01: Addetd top hook for 25mm thick shackles with inner Diameter 100mm. Since theft protection is an important issue…
One of my friends wants a 1:1 scale model of a german Bundeswehr MG3. I found a model in the Sketchup 3D warehouse from mandun, cut it into printable pieces, added a pin for better assembly and tweaked it here and there to get it…
Just a Remix of the Logitech G305 battery cover with Logitech Logo
simple block for mounting the camera in the corner with the default base and strain relief I had some spare SPAX screws here. If you want other screws, modify the attached AutoCAD file. BOM: 2x SPAX Screw 4mm for wall mounting 2x SPAX…
This is a simple stand for the Anbernic RG35XX. I was having some trouble with bed adhesion so I added tiny tabs on the corners that are easy to cut off and added that as a second STL file. They are 0.15mm tall so they should only be 1-2…
Alternative mouse shell for G305 - Semi Ergo Shape - GPRO Feet compatible - LiPo replacement. Best filament with most accurate results is Extrudr XPETG so far. It does not warp like PLA or regular PETG and has good sanding properties.…
A comfort grip (for when the device is opened/in play) and a standing case (for when the clamshell is closed) for the iconic Anbernic RG35XX SP. It has access to all the ports on the side and bottom of the device. It can be printed with…
I picked up one of these cheap wireless Android Auto/Apple CarPlay displays from Amazon (specifically the 9.26" one from VSTARK which was going for about $189 before coupon at the time of this writing). Rather than plopping it on top of…
I did not have any 5mm length M3 screws, so I had to add a nut as a spacer to get the right depth. You will need some M3 5mm long screws, and some nuts to drop in when you set the pause in the layer height. Here is a video of the M3 nuts…
RG35XX Skadis mount Print the model in the default orientation, with supports enabled. You may need to sand down the pegs in order for it to easily fit in the pegboard. I have also included the .step files with and without the pegs, in…
Converter for M22 water faucet to G3/4 garden hose connector. Use teflon tape for a better seal. I printed this in PLA, but PETG is recommended if you plan to run hot water through it. Print Settings Printer Brand: Prusa Printer: i3 MK3…
Information about the model: Inside the case there is about 1mm of play on each side so that foam rubber or similar damping can be attached. The lower shell (Part_2) has an elevation so that the shoulder buttons are not pressed in.…
Anbernic RG351p case. Designed to be printed as one model without supports The height of the case is made to add the original white foam that is added in the box with the console. If you don't have this foam the console rattles a little…
Simple model. I recommend 0,15 layer and 4 walls for higher strength.
Meet the sub-40g Z(H)ero Mouse, inspired by Optimums Zero Mouse. Parts required: -Logitech G305 Lightspeed https://amzn.to/3EqIv8R -Lightweight Lithium Battery https://amzn.to/4hvylmi No additional screws/hardware required! I designed…
Simple vertical stand for HP Elitedesk/Prodesk G3-G5 mini. Printed with 0,2 layer, 4-6 perimeters, infill gyroid 10-25% (printed 0,2, 6, 25) 2 variants. For HP Elitedesk 800 mini or HP Prodesk 600 mini. Line G3, G4 and G5. 3mf files for…
I received an old Unifi G3 bullet without any of the mounting for it, so i borrowed a friends mount and made my own. it works pretty good. I recommend printing this in ABS, ASA, or PETG if your using it outside. but I'm sure depending on…
If you like this model, show some love, hit the like button. Version 2 of the ergonomic grip for the Anbernic RG 35XX (RG35XX). Now has rounder corners for comfort and different printing orientation. Print in PLA Needs supports
UniFi's G3 Instant is a great little camera, but it tends to fall over, especially if there are children nearby. This model creates a basic stand for the camera, making it harder to tip over. Includes a rear opening for the power cable.
Adapter 3/4" Garden Hose Thread to G3/4" (Gasgewinde)
The Anbernic RG35XXSP is a retro handheld emulation game console that runs on Linux. It's design is boxy and this is for people who want a little bit more grip to the console, but still keep the slim and portable nature of the console. I…
a seal is needed for the pet bottle, I use the pet bottle, which serves as a pressure vessel, keeps the pressure up to about 4BAR na pet lahev je třeba těsnění, použávám k pet lahvi, která slouří jako tlaková nádoba, udrží tlak do cca 4BAR
I broke my cover so I made a new one ;) Fits my HP EliteDesk 800 G3 Desktop Mini but should also fit the previous and later models of the mini. If not the .step file is included for they who want to modify. I suggest printing in 100%…
A slip on button and screen cover for the RG35XX Plus. Wide opening for USB-C cable clearance. Print without supports.
HP ProDesk 600 G3 mini mount compatible for mount into an IKEA pax cabinet hardware needed: 2x M4 x 10 mm countersunk head screw 4x euro screws 6,3 x 16 mm (for example from IKEA)
JREV Floor Extension
Shorter version of my picatinny G36 carry handle. It measures 11.618" (295.09mm) in length. I use filament strands to align the rail section. Hardware: V1: 3x 6-32x1.125" Pan head bolts and nuts V2+: 3x M3x25mm Socket head bolts and nuts…
Mount for a UniFi G3 Instant camera to a baby crib. You can route the USB cable through the holes in the model to hide the cable neatly. I recommend printing both models upside down, with supports on. I'm fairly certain that the clamps…
A display stand for your RG35XX or RG35XX Plus. Simply place the hand-held in to the stand and it will automatically start charging, so you’re always ready to game on the go! 8.5 mm rubber feet: https://amzn.to/4aqaWQ1 Specific USB-A -…
While the G3 Bullets are weatherproof, it can't hurt to protect them from the elements. I use this shroud to protect my G3 Bullet while captuing an outdoor timelapse of the countryside, attached to a pole on my roof. UPDATE: Added slotted…
Hi! this is my first design after a few weeks of practice, i hope you enjoy it. Waiting for those makes!
Thread reduction for pipe G1/2 to G3/4. I created it to connect garden water cooling.
Follower glock G17, G17L, G19, G19X, G26, G34, G45
Spend $20 for rack-mount ears for my Cisco 10-port switch!? Forget that! These printed ears are MORE than strong enough at 30 percent infill, even with some other stuff stacked on the switch in the rack. My SG300-10P used 12mm long M4…
This case is made of two halves that can be connected with either a length of filament, or the use of #16 finish nails as “hinge pins” to connect them together. The case features a slot in the back to use as a display stand when not being…
Please feel free to remix the design and print for selling it, please upload remixes. G36 speedloader for easy and quick magazine loading, first couple mags are loaded in same speed as with loading using fingers, diffrence is felt when…
Part G35 of the Real Grade Gundam Unicorn is prone to breakage so I modeled a replacement part. Printed it out of an ABSLike resin and it has held up over two years and through multiple transformations.
Deutsche Version unten. Parts required Adapter board TH3P4G3 with ATX bracket GPU with max 3 slots height. Length is not relevant, you can print as many externders as you need ATX power supply 4 screws to mount the power supply m3…
This is a simple, fully 3D-printable charging port for the Ninebot G30/G2, designed with flexibility in mind. You can choose between versions that accommodate an XT60 connector with or without a button, depending on the file you select.…
This case has been designed to replcae the lid of the GMKTec G3 Plus (Intel N150) to give active airflow to the NVME and RAM. Numerous variations/combos available: 80mm and 60mm fans 25mm and 15mm fan heights Enclosed or flat for mounting…
Wall mount for the Unifi Access G2/G3 reader
Model This allows you to hard mount a Sennheiser G2/G3/G4 RX or TX Lavalier pack on your camera rig / audio recorder. You can either use the stainless steel belt buckle to attach the 3D printed plate or double sided tape (Recommended -…
A big thanks to pfml for providing his brilliant "quick and dirty" rack! In my setup, the VESA mount holes didn’t fit perfectly, so I modified the design and added more flexible holes to ensure better compatibility. further information:…
Hi everyone, it's been a few years since I bought a Cinelog35 V2 frame and I was trying to redraw it in case I needed to make a new part. The manufacturer didn't have a proper drawing of this frame, so I gave up for the sake of final…
Love the rugged box model and decided to adapt it for use with my RG35xx I left about 2mm of space all around the device to be able to add some foam padding. For the padding on the face I used the foam that the device was shipped with.…
Stand for G3 Instant camera, fits with wallclip and cable.
Overview A friend of mine was getting these UniFi G3/G4 bullet cameras returned from remote sites without the bases, and unfortunately, Ubiquiti doesn't sell the mount as a standalone piece. If you're going to be installing these outside,…
Adapter for connecting the 4.6 mm tube of the Gardena Microdrip system with any G3/4 thread, for instance a magnetic valve or the water faucet. Additionally, you will need a G3/4 sealing to make the connection water-tight. Please note…
3D model of the famous HK G3 rifle that serves throughout the world to this day, the design isn't great since I'm just a beginner in Blender and it probably needs some tweaking to be printed but it would work as a model for a Unity…
Taschenhalter für Segway Ninebot Max G30D II Die Tasche wird normal Innen befestigt. Ich bin jedes Mal beim Auf oder Absteigen daran hängen geblieben. Wenn man sie Vorne und am Lenker befestigt, wird das Licht verdeckt und man kommt…
Clean display stand for this amazing little machine
Please respect the Licence the thing comes with! Thanks Thanks to user "Threat_Craft" who test printed the prototype, provided pictures and the dimensions so I was able to adapt the epic ultra to the RG353m as I don't own it myself.…
Ninebot G30 Spacer is used to install a bigger battery in the battery compartment. This is my version with 7mm walls. If needed you can grind down the top siderails where the spacer is mounted for even more space. Perfect for…
I was looking for a decent G3 instant corner mount that allowed me to hide the power cable. I really liked the design of Tadufeu but it lacked the feature to hide my cables so I created a remix for this purpose. Don't mind the finish off…
UPDATE: Included another version of the grip that includes some ridges inside where the device goes. It holds the device much tighter where it will not slide out by accident. It did create some small scratches on the side of RG35XX Plus…
Rear Axle Bracket as reinforcement and for 125mm axle drop out motor brake disc mount adapter
I designed this to replace the Apple case logo on the old iBook G3 laptops from 1999/2000(they fall off and get lost very easily after all these years). It can be printed in resin or fdm. I was going to print the final part in resin, but…
