32 models
This is a case for the popular GM328A transistor tester. The case is able to be printed with no supports, and requires Four M3 socket head screws and four M3 square nuts to assemble. The circuit board is captured between the top and…
I needed a decent case for the recent edition of gm328, but did not want to fiddle with screws. Found a good model by machanzar and tweaked it slightly. It should not require any screws now and works with a friction fit. Worst case…
There are many variations of the GM328A component tester, this case is for the “2022 Type-C” model. There are many variations of these boards out there and none of the other cases fit my model or my needs. The files are pre-oriented for…
This case is based to the GM328 "SMD" black board dimension bought on famous chinese site. It is not suitable with the board with standard components, The idea was to print a full case and have the opportunity to use a 9V battery or…
Full-featured case for GM328A TFT Transistor tester variant and 18650 Li-Ion battery. Charger module is Q3962A with attempt at light conductors for it's indicators (and it actually works). Step-up module is MT3608. Knobs are from some…
Hardware needed: 8x M3x10mm screws 4x M3 nuts Rocker switch 29x12mm (feel free to remix if using different one, hole in default design is 30x13mm, max depth is 27mm) 9V battery and connector Panel mounted 4MM banana sockets GM328A board…
Jedná se o remix modelu friction fit GM328A case od autora kolba Přidány číslice 1112333 pod měřící objímku, upraven výřez pro displej (je vidět pouze displej), přidáno osazení pro hlavičky šroubků, spodní část zvětšena tak, aby se…
Enclosure / box for GM328 transistor tester. Including places for 18650 dual batteries, USB microB charging module with BMS, step-up module and 1S battery indicator module. Extra parts required: 2x 15x10mm rocker switch 7x M3 bolts L20mm…
The original model by ressu can be downloaded here . Changes from the original: Redesigned the wall near the lever. The original model has a strange dust-gathering hole there. If you measure SMD components, a tiny thing can jump inside…
Do pobrania mój projekt obudowy i zasilania do Analizatora/Miernika GM328A. Do zasilania wykorzystane ogniwo 18650, lista części: Miernik GM328A https://alii.pub/6vtt92 Konwerter J5019 DC DC Step Up i ładowarka Li-ion Wskaźnik baterii 1s…
An enclosure/battery holder for the GM328 transistor tester. The box has a simple hinge that holds the battery in place under the tester, while leaving the board surface perfectly flush on the enclosure's rounded edge. This leaves all the…
This is a remix of https://www.thingiverse.com/thing:2775688 I wanted to be able to access the battery with one screw. I also wanted the device to be at an angle but not too steep so the test components don't fall out while working with…
This case is more or less a set of replacement parts for the most common acrylic case sold for housing the DIY GM328 component tester. While it includes replacement parts for all the acrylic parts of the original case, with exception to…
Description Started this design back when there were no proper cases for the newer GM328A USB-C version here or anywhere else. Uploaded it here along with the FreeCAD source in case anybody else needs it. Printing and Assembly Can be…
There is so much different version of this transistor tester that I didn't find a case for it ... So in the pure DIY spirit I made my own. I hope it will suit someone else's one. This is a case for the DIY Transistor tester GM328. You can…
A custom 9V battery enclosure designed for the GM328A Type-C LCR-T tester.
I had a transistor/capacitor tester sitting in a drawer for a couple of years, always meant to make a case. I finally did, and knocked it off the desk, breaking it just before putting it in said case. :-( I've since ordered a new one but…
The tester case is modeled for use with a 6F22 battery. There is an LED on the board for which a light guide is made, which is recommended to be printed from a translucent material.
This object is a case for the GM328A Electronic Components Tester. It has a compartment for the 9V battery and an access hole for the extra test leads. The thin plate on the battery cover should be placed between the Component Tester and…
This ia a box for the GM328A Component Tester. It is possible to use a 9V block battery or external power via connector. The Zero-Force-Socket must be put onto two extensions to fit into the front plate. The backblane must be made out…
A remix of the remix with improved lettering and optional model type and warning labels. The lettering in the remix this is based on was slightly too small to print well using a 0.4 mm nozzle. This redesign uses larger letters and a…
A box to protect the exposed components on the GM328A electronic component tester. The lid is a press-fit, very tight, but this is the sort of enclosure that you really won't need to open often, should be set-and-forget once the lid is…
Made for this unit: https://s.click.aliexpress.com/e/_c3UEMT8x This custom 3D printed enclosure is designed for the LCD GM328A Component Tester . It provides a precise fit for the device while protecting the LCD screen, ZIF socket, rotary…
Box for GM328 Component Transistor Tester. Modified to use Rotary Encoder and default component socket. Two versions of top cover one with rounded corners (Fillets) and one without. remix of http://www.thingiverse.com/thing:1277163 Print…
This is a low profile tilting stand for the GM328 electronic component tester, designed to work with the most commonly used acrylic case. Included is a replacement part for the acrylic bottom plate and a copy of the stand I originally…
This case is more or less a set of replacement parts for the most common acrylic case sold for housing the DIY GM328 component tester. While it includes replacement parts for all the acrylic parts of the original case, with exception to…
An enclosure for the GM328 transistor tester, pcb just closing the box, so the components, are in plain sight, no cover. used some battery from powerbank, tp4056 for charging, MT3608 DC-DC module and 10x15 switch. + stands and screws from…
Inspired by raspberry pi din rail holder https://www.printables.com/model/472867-raspberry-pi-din-rail-mount , with M3 bolt to secure it
A remix of the remix with improved lettering and optional model type and warning labels. The lettering in the remix this is based on was slightly too small to print well using a 0.4 mm nozzle. This redesign uses larger letters and a…
A easy to print stand and encasement for the popular GM328A component testers. There are two versions, the smaller version just holds the tester, and has two narrow parts trays, the larger one has a battery compartment under the board and…
The GM328A V1.20 component tester went through a couple of iterations. Therefore, this specific version has become hard to come by. The base prints with slots for M3 nuts. The PCB is mounted with 5mm long M3 screws. The holes and slots…
