Counting matching models…
ChopstickCheaters to let your kids eat with chopsticks. Easy and fast print and a lot of fun! V2 now prints with no supports. Use PETG to be able to put them in the dishwasher. PLA works fine but may not stand the heat. Made for…
Background As many of you have found, it is easier to swap MK4 Nextruder nozzles in-place rather than to disconnect and swap out the entire heater block. Problem In-Place Nozzle Swaps pose some amount of risk in that you have to hold onto…
For bambulab users: you can find the model including print profiles here on makerworld . I wanted a drill press for my Dremel, as well as a dedicated press for installing heat-set inserts with my soldering iron. Since there are already…
Be one of ten who leave a Like at Printables and support me with it :) Prevents cable breakage at the housing outlet and rubbing on the Y-axis motor. It can be attached to the underside of the housing and to the recess for the stepper…
Bau einer beheizten und aktiv belüfteten Filament Trockenbox. Gesteuert durch einen Arduino Nano. Gebaut aus einer Ikea365 10,4L Vorratsbox, ein paar elektronische Teile und ein paar Teilen aus dem 3D-Drucker. Alle Teile sind leicht zu…
Inspired by the design from FUN CHOP chopstick helpers. Great for rounded chop sticks as well. Recommend Print in PETG for flex and strength. Recommend 100% Infill FunChop chopstick Helpers (Amazon Link⬇) https://a.co/d/1i6oWUr
Ender 3 S1 Pro Heated Bed Cable Chain. This chain link provides the offset needed from the heated bed to the printer. I used a little bit of Automotive black silicone to adhere the bottom part to the machine. You need to print: 1x…
Notice! This is only compatible with Python for the original AMS. Please view my other designs for designs supporting other AMS systems, there are plenty. Buy Python I've teamed up with a few different stores around the world offering the…
As of now, the (Un)original Dryer D2 is available. It is an improved version of this drybox, with many new features. Now supporting modular heating, filament weighing, and is much easier to assemble! Check it out here: Disclaimer: This…
This model might not be strictly needed to prevent the wires from being damaged as they are pretty beefy, but having all the wires on the printer match is fun! The design uses 17 ChainLatches, 17 ChainLinks, 1 ChainEnd, and 1 ChainStart.…
I decided to build this mod for the CFS just to see if it could be done. Like many of you, I received the Space Pi dual roll filament dryer with my K2 Plus preorder. I have multiple other filament dryers, and really no use for another…
UPDATE: I have replaced the files with STEP so it's easier to remix as QIDI changed up the mounting locations and i don't have acces to this data. Attempt this fix at your own discretion! Only work on the heater with the power off and the…
Less stress on the wiring and more gap for twisting than shorter model. Slightly longer (9mm) but less prone to insulation melting. Modified from original Prusa model files. Use with original clip
The front edge of the print plate should sit 38mm behind the front edge of the frame so here is the jig for that.
!!!!!! It has come to my attention that not all 40T gears are the same. Some have a much bigger shoulder and are much thicker. I got mine on Amazon. link below. The wrong 40T has an option of a shaft up to 15mm, The cheaper version only…
Cut out the sock and heater from Said's model and pasted onto this version
Updates: After printing mine, I realized my 6mm x 2mm magnets were too weak. The heater is held to the wall but uses the power cord to stay up, added a 10mm and 8mm magnet version Added a clearance hole for the heater button Added a 2mm…
Heatsink was completely reworked, collets were remade as close to original as possible. Since provided model was fused into one solid, E3 Collet is rough estimation according to drawings/photos. CAD is accurate to provided technical…
This is one of the first accessories I designed for my S1 Pro. If you own one you probably know what this is for. I've been using this for a year and I have none of the typical cable insulation damage nor have I ever grabbed the y-axis…
The COREBOXX Semi-Smart is an advanced electronic upgrade for your filament storage system, enhancing usability, safety, and functionality. This modular system integrates filament chamber heating, real-time monitoring, and quick control…
T-Bleed key for Heaters The Würth Air Bleeder Tool is designed to facilitate the removal of air from the heaters/radiator, which is essential for maintaining heatrer efficiency and preventing potential loss of heating capacity due to…
UPDATE: V2 Da die vorherige erste Version nach Benutzung und anschließender Fahrt mit dem Wohnwagen immer wieder herausfiel oder sich sehr leicht lösen ließ, habe ich mich dazu entschlossen das Teil so zu modifizieren, dass es nun in die…
It is again the time to throw the heaters on, also the time to bleed the heaters. I have already printed something similar some years ago but unfortunately no longer found therefore I have tinkered a new one. No support needed, just part…
Use 3 walls and tree supports on build plate only for water catcher. A simple tool that makes bleeding radiators cleaner and more convenient by catching the water released from the bleed valve. The design consists of two parts : A…
Simple and stable hanger hook. Click fits Stays tightly on place 2cm rail diameter Print instructions PETG is the best, but PLA works great as well. 0.3mm layer height is just fine.
Print flat sides down no supports. To use, plug into 12v 10amp power supply. Insert tool into coil and hold down the button until it glows, this usually takes a few seconds. Assembly instructions: Insert both the button and the power…
Relieve rubbing of the cord on the table, corner and frame. Keep cord parallel to the bed movement. Presses onto cord no fastening required.
Certain times through a print I noticed the cable catching on the corner of the power box, with a slight bump as the bed pulled it over. This clip just ensures a forced direction for the cable which does not interfere with the power box.…
Was looking for a good fan duct with 360° cooling and good nozzle visibility of Kobra S1 and decided to make this one for upgraded hotends (with ceramic heater). The model is easy to print with or without supports (up to you). Please…
The Creality Ender 3 comes with minimum thought put into the cable management aspect of the machine. This could lead to broken and shorted wires, or cables getting caught on other components of the machine leading to damage or print…
The Ender 3 S1 Plus has a slightly different heat bed cable positioning (and it's also bigger), so I mirrored the offset chain link to fit the specs. I also recommend printing the cable bracket link laid down with minimum support. I…
Im proud to release the version 1 of my universal chamber heater, the control system and power setup will be up to you, I will add these details later on the next version. BOM: 1 x 24v 7530 Dual Ball Bearing GDStime Blower Fan…
How to diagnose a failed heater flap: There is no hot air blowing from the HVAC in the Astra, First checked the coolant in the engine, if there is none, you might have a bigger problem. Check if the the mix flap solenoid is working by…
You can buy this model printed in PETG along with the needed gaskets so you don't have to buy a 50 pack, message me! Disconnects the Heater Hose Fittings on 2012-2018 Ford Focus 2.0L and 2013-2016 Ford Escape 2.0L Eco Boost. This video…
Updated - On my second K2 the 90mm fan spacer interfered a bit with the purge chute, so I opened up the clearances around that a bit more. It wasn't sitting right on the can and got pushed in enough to interfere with the blades and cause…
Seatbelt cheater designed for a 2010 Ford Focus. For all legal purposes, or whatever, I'm not your mom. Category: Vehicles
This is a replacement wall mount plate for the control panel of the popular Chinese diesel heaters, as used in many self-built motorhomes. It clips the control panel into place the same as the original mount using the same screw…
Remix of Noizie Works awesome chamber heater shell replacement, with several design improvements. He has given me his blessings to remix the hell out of this. Removed previous thermocoupler wire path. Added through barrier wire path.…
Fits EcoFlow WAVE 2 Portable Air Conditioner with Heater exhaust ducts E and D. It is hard to cut a perfect circle, so print these, screw and/or glue it to the board for a perfect fit. Cut the board to the size of your window and put some…
Dead simple but very useful symmetric hook hanger. Hang it on bathroom rail heater. It click fits! It stops on the bars under the one you hang it on (stops wiggling). Hang it on the panel heater. It fits in the top holes. Useful to hang…
Simple model to elevate the diesel heater so the exhaust pipe does not come in contact with anything. This is for the tall and slim all in one models. I used 4 M5 screws that thread into the plastic foot. But if you have a screw long…
HARDWARE NEEDED: 4 x m5 heated inserts 4 x m5x12 screws 4 x m3 heated inserts 4 x m3x8 screws PRINT SETTINGS: Base: Infill: 20% Walls: 3 Support: Yes, Normal (manual) Tube: Infill: 20% Walls: 4 Support: Yes, Tree (auto) Controller Mount:…
Tool for remove the XH 2pin connector nozzle heater of centauri carbon Updated (16Feb26): Added New puller for ZH 2pin with printed spring. Updated (15Jan26): Added New puller for XH 2pin with printed spring. This version prevents the…
Radiators/water heaters should be degassed before the heating season to increase efficiency of the heating and prevent issues. Every time I used a cup or almost anything to vent the radiators I got water on the floor or on the wall.…
I recommend printing from PETG CF, better from PA CF. Attention - the upper elements must be compressed. The special feature of the mount is that you can quickly remove and put back the heater.
Before you print, please read everything below carefully... What: Based off of SE3Ds 7.5 mm panel spacer, I modified one of the lower pieces to have two wire relief holes to be able to route a creality chamber heater inside the printer.…
MODEL DETAILS Connector clips for the joint of your wiring where the HeaterCore and extension cables meet. This is not a mandatory part of the installation. You will need 4x cable ties. RECOMMENDED PRINT SETTINGS No support material is…
An updated bracket for the Adafruit Heated Insert Press (https://learn.adafruit.com/heat-set-rig) The original bracket requires 4 screws to hold the top plate in place. I wanted to be able to remove my soldering iron quickly without tools…
Remixed model to lay flat for wall mounting.
This mod allow you to install two additional Fans under the bed. I am getting about +10°C 4x M3 Inserts.. to mount the Fans. (Voron BOM) 2x M3x8 (Voron BOM) 2x T-Nuts for 2020 Aluminum Extrusion (Voron BOM)
For a 55 mm ID air outlet. You can connect a 22 mm OD hot air pipe to the four outlets and plug them in your wet shoes/boots . Test print with PETG, 0.25 mm layer with supports. It's possibly better to use ABS/ASA but I don't have this…
Printed in ABS you can watch more instructions in this video: https://youtu.be/Fi0ZqGbZryw Editor note: I want to add that installing some kind of fuse is gonna be a good idea and if you pass the wire true the metal to use a rubber…
This is a remix of ANYCUBIC MONO X HEATER by JVJV - Thingiverse I found that there was a need for more room inside for cable management, so I have extended the compartment for the thermostat. Text below is copied from the original…
Replacement Chamber Heater Cover Unit for Qidi Plus 4 Model Update: I've added a revision to the original model that includes a more curved path towards the outlet which slightly improves the overall air-flow. These models will have the…
Needed a quick key to vent my heaters where the skrew driver slit was dead. Works in normal german central water heaters. Used PLA, but PETG would be more stable. Used Prusa Mini+ with 0.4 Nozzle.
These wago holders are used to mount the wagos included in the Honey Badger bed heater installation kit. Use the 412 for 2 port wagos, and the 413 for 3 port. Use standard Voron print settings.
RV 4 inch flex hose repair elbow. This was created to address sharp 90° transitions in RV's like the Forest River Salem Cruise Lite that lead to broken/torn heater flex hose. Under the fridge, a 4 inch flex hose is routed right behind the…
This vent design adds a curved lip to let the lower electronics chamber vent out convection heat through the exhaust port while also giving the heated chamber fan a wide path to vent out toasty air. All while keeping the two from mixing.…
This hanger will clamp to the heater and stick. Use the f3d file to adjust all parameter according to your needs. Print Settings Printer Brand: Anycubic Printer: Photon Rafts: Doesn't Matter Supports: No Resolution: 0,02 Infill: 10%…
Нагреватель строго рекомендую печатать из термостойкого материала, в идеале не поддерживающего горение. При использовании нагревателя на 200 Вт рекомендую использовать внешнее реле на ток не ниже 20 Ампер Терморегулятор:…
I have been working on this for a while. I didn't want to pay over a hundred dollars for a 4-spool heater that was mediocre in heating the filament. The box is more effective than I thought it could be. When I had 7/9 spools loaded the…
Use a filament that can withstand the temperatures. ABS works fine.
These are helpful when someone is still learning how to use chopsticks. Depending on how the chopsticks break, you might need to shave down the wood a bit to make it fit properly Printing notes: The “Basic” Chopstick Cheater in the photo…
These parts were inspired from a design by KeeganBuilds (YouTube). I modeled these parts in OpenSCAD to fit the components from a 2 kW diesel heater kit and have included the .SCAD files below so others can modify to fit heaters with…
I build the Lack enclosure for my Ender 3 Pro but the cable of the heated bed constantly was bended in weird was at the back panel because a couple of centimeters were missing. My solution is a cable strain relief replacing the original…
Adaptor to change the 80mm Dia to one which can be between the zipper. Fusion360 files included.
I had this second hand gas heater, the Truma E2400, but this part was missing and it appears to be smaller in diameter than the spare parts you can buy …. So I designed one (from pictures & measurement of the parts you screw it on) and…
Update – Version 1.2 Design Update: Added a lightning bolt icon to represent the power lines. Improved Clearance ("Large Fit"): Transitioned from a "perfect fit" to a "large fit" . The extra room for the rubber grommet and cables makes…
Modification to allow for thick wires on the Prusa Heated Bed Prusa Bear Printer Design by gregsaun https://github.com/gregsaun/prusa_i3_bear_upgrade
Seat Belt cheater for 2021 Ford Ranger
Renault Clio II. / Thalia ventillation system one of the gear usually breaks. This is a replacement gear. Need some voltage reduction to not breake the 3D printed gear.
Print Install 2x 3*3*5 heat inserts Attach an SSR with 2 M3 screws Attach the mount on the rib next to the motherboard. BOM: 2x 3*3*5 heat inserts 2x M3 screws Creality K1 series heatbed upgrade - Graphite Bed available on Aliexpress: K1…
I designed this to get my PTC heater up off of the heated enclosure floor to allow airflow for the fan. Printed in ASA. No supports. The heater I used was this: Constant temperature Electric fan heater PTC fan Auto heater Small space…
Хочу поделиться с вами моделями, которые я делал в ходе модернизации своего принтера Elegoo Centauri Carbon, чтобы получить активную камеру. Всего это 5 файлов: Фиксация проводов для вывода их из камеры (2 файла), рампа для циркуляции…
I decided to make my Lego Skeleton in to a castle era model. Looking online there were not any high quality shield STLs available. Using a stl from printablebricks as a template, I rebuilt it in tinkercad and included the classic Wolfpack…
Reinforcement parts for a Peugeot 407 heater flap. As used in this video The steel spine is not shown here as it is not 3D printed but easy to make elsewhere. The parts were printed from PETG 5 perimeters with 50% infill to give as much…
This is a tool for the home services. This model is prepare for a heater vent repair. Size of the square inside is 5x5 mm. Printing: Is it better to print it from PETG or ABS in laying down positionto make the tool stronger. For the print…
Voron V0.1 3x Wago 221-412 mount for the bed heater Based on the Voron V2 / 2020 mounts by Boingomw which you can find at https://github.com/boingomw/VoronUsers/tree/master/printer_mods/Boingomw/Wago_mount Use 2x M3x8 SHCS to secure them.…
Shrinks the footprint of the printer in the y-axis. 60 deg so that x and y cables never rub and decreases strain on cable wrap. Uses stock M3 hardware but screw heads on top making it easier to assemble. This print only works with the…
This is a threaded plug that is designed to fit in the anode port of a Suburban brand hot water heater commonly found in RVs and travel trailers. The plug has a grid-shaped vent to allow for airflow into and out of the water heater…
…Please be sure to hit like & post a make, I'd love to see your prints! WARNING! If you do not know how to wire this system correctly & safely I STRONGLY recommend you DO NOT attempt to print or use this model as you are dealing with…
Designed this prop opera glasses / theater binoculars for a friends birthday. There are holes so you can look through them. I printed them "looking" upwards. Supports are needed for the middle bit and under the arm. Enjoy! Category: Props
This is a modular 3D printable silhouette based on the TV show Mystery Science Theater 3000 (MST3K). Put it on the your TV, computer screen, or even a window! MST3K Silhouette.stl has the 3 characters and is just over six seats wide, and…
A heater mounting bracket for the Elegoo Mars 4 Ultra Resin printer using a specific off the shelf 12v 5 amp heater unit. https://www.amazon.com/dp/B0BL6WZPM9?psc=1&ref=ppx_yo2ov_dt_b_product_details…
Description Here is a mounting solution for Chitu Systems Mini Heater H2 inside the Centauri Carbon. Installation This mounts to the M3 threaded hole located on the left side of the printers base. I used Fleeeinlan3D's version of SE3D's…
An artistic mask, perfect for home decoration, artistic performances, costumes, or simply experimenting with painting and finishes. In this file, you will find the mask with or without the attachment system. I also added a .3mf files to…
I designed this Chamber Heater Adapter for the Elegoo Centauri Carbon to be a clean, secure, and fully reversible way to add active chamber heating to the printer—without drilling, cutting, or permanent modifications. This model is an…
This is a mod for the Phrozen Sonic Mighty 8K/12K. It is a lid spacer/riser and frame for a PTC heater and W2310 temperature controller. The spacer is used so that there is no drilling/cutting of the cover and base for cabling and…
Example picture was made on hatchbox petg with 4 perimeters and 7 top and bottom layers, .16 layer height 80% infill probably overkill but it works
Tool for bypassing Xerox door interlock switches. A must-have for performing repairs on any Xerox production press. Compatible with most Xerox interlock switches 8 minute print No post-processing F3D file included Recommended settings: No…
Winter has come and the children are outside all the time. They only come in briefly to eat at lunchtime. The robe drips every time. And the space on the towel dryer is tight. Towel dryer? There is no room for towels here! :D I designed a…
This project enhances the safety and reliability of a the Qidi Plus4 chamber heater by upgrading critical components and adding multiple layers of protection. The modifications include replacing the original 5A Solid State Relay (SSR)…
I am providing two files, I personal used the one without the notch and then cut it out my self. I made the second one with the notch after I found out it wouldnt fit. vent ring can be found on @Conrad_F89, or go to the remixed link you…
Reusing the PolyDryer's Hydrometer to monitor the humidity in my enclosure.
Slide it on like the pictures show. Orient the print like the sliced pic, no supports needed. Enjoy
In Diameter 75.8 mm Chinese diesel Air Heater Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: Yes Resolution: 0.16 Infill: 25% Filament: Polymaker Polyflex TPU Black Category: Automotive
This is a very simle print to organise your towels on the radiator. Quick installation, no drilling or gluing required. It can be easily hung Any position on the radiator at different heights and any time intervals.
Thanks for sharing from the author Follow me for other drawings that may be useful to you. Happy Printing
Made this for a heater that attaches to a Coleman 1lb propane tank. Without the stand, the slightest nudge would make it fall over. With the stand, it can be smacked around and will stay upright. Printed in PETG, no supports, 15% gyroid…
Uses 8x2 magnets Might not need to use all slots depending on how strong your magnets are.
![Qidi Plus 4 Safer Chamber Heater [Updated]](https://media.printables.com/media/prints/1063634/images/8049273_cb181092-f34b-4857-8f42-249d8d05654f_d6c7f8bf-32c3-40c1-90f4-f35553f6bfa7/2024-11-05_10-15-55.jpg)
