Counting matching models…
This remixed part will serve as a replacement for the stock GoPro mount in order to provide a location for mounting 21x21 mm HGLRC M100-5883 GPS module on a SpeedyBee Mario 5 frame. GPS mount with GoPro v2: better fit and easier…
A simple mount for the HGLRC M100 GPS module. Versions: - Plain - Flightory Mini Plank Hatch fitted
GPS mount for FlyFish Volador VX5 for the original antenna mount, compatible with all GPS units with dimensions of 21x21mm. No screws are required to mount the module. Print settings: Material - TPU Infill - 50% Walls - 3
This remixed part will serve as a replacement for the stock GoPro mount in order to provide a location for mounting 15x15 mm HGLRC M100-MINI GPS module on a SpeedyBee Mario 5 frame.
HGLRC M100-5883 GPS zip tie mount for a FPV frame. This model is designed to fit securely on the top plate of the GepRC Mark4 7" drone frame. Recommended Print Settings: Material: TPU or ELASTAN (TPU 95A used in this case) Infill: 20%…
Printed with PETG with .1 layer height. The MAG Alignment in Betaflight should be set to CW 90° in the config tab. But also confirm that the compass points the right direction in the setup tab.
There are a few mounts around to get the M100 onto the Flywoo Explorer LR, but a lot of them have large covered portions that make me think that heat dissipation wasn't a factor in the designs. With this mount I left both the top and…
Print as oriented with support in TPU . Wanted a battery holder that was a bit more snug than the one provided with the drone.
HGLRC M100-5883 M10 mount GEPRC MARK5 DC TPU
TPU GPS mount - HGLRC M80 Pro
Must be printed with TPU
I am new to printing and drones an i couldnt find a mount for the M100 from HGLRC so i made a simple one. TPU 30 % infill (maybe less but thats what i went with)
GPS mount for HGLRC M100-5883 + Source One V6 Print in TPU. Use 0.2 mm layer height, 30% infill, tree supports ON, build plate only OFF, remove small overhangs OFF.
Remixed the mount for a smaller GPS Category: 3D Printing
HGLR M100 Mini mount GEPRC MARK5 DC
Flight Controller Guard for HGLRC Sector 5 V3 Frame. The fit is pretty snug (with PETG , with tpu i have tested and is not that much feasible) Heavily inspired by the Roma V2 Guards ;) Print Settings Printer: Artillery Genius Pro Rafts:…
Custom battery holders for the HGLRC Baby Shark/Drashark micro drone, designed for a variety of batteries. While they mirror the original holder's aesthetics, these ensure a superior fit. I've listed sizes and their corresponding…
I made this for someone that needed one and I figured that I would upload it here to make it available for other people. It's meant to be printed in TPU. I have neither printed nor tested this myself, but the photos are from the person I…
Simple TPU mount. Print top facing side down to avoid overhangs and to get nice surface finish.
HGLRC M100 Mini Arm adaptor for ApexLR 7
Fits the standard GPS cutout location on the AR Wing Pro. It is a friction fit, but I recommend using a bit of glue to secure it.
I didn't find the back part of the Nazgul Evoque properly 3D modeled on the internet for additional GPS module, so I designed an almost exact replica of the part where the XT60 and the video antenna are and extended it for the HGLRC M100…
Racing canopy for "HGLRC Batman 220" drone frame. This canopy is only compatible with the micro camera series (L19mm*W19mm).
This is a frame for the HGLRC Petrel 75 whoop ready to fly kit converted to a 75mm toothpick frame. It is based on the HGLRC 120 carbon toothpick frame. The mini whoop uses a 25.5 mm AIO mounting holes for the flight controller. The motor…
Made the mount using the original GoPro mount as base to fit my HGLRC m100 5838, made 2 holes in the front so you still see the lights. New version combine gopro mount and gps.
This is a mount for the HGLRC M80 GPS unit. You can print it vertically or place it on the back wall. Recommended settings: Material - TPU (SainSmart) Temp - 230/50 Infil - 100% rectilinear Mode - speed Nozzle - 0.4mm Layer height - 0.2mm
Lightweight canopy for tinywhoops that holds camera (Caddx Ant) and vtx (HGLRC Zeus Nano).
GPS Mount inspired by https://www.printables.com/model/764135-quadmula-siren-f3-gep-m10-gps This fits a HGLRC M100 Mini GPS, or any GPS with the following dimensions: Width: 1.5cm Depth: 1.5cm Height: 0.5cm
Gedruckt aus PLA von Sunlu in 0,2mm. Keine Stützen notwendig !!!
Case for drone with 4 additional batteries
Unfortunately, the standard camera of the Walksnail Avatar digital FPV system does not fit in the HGLRC Rekon7 frame. In order to be able to install the system anyway, I designed other mounting plates and an adapter for the VTX. I have…
Here is my gps mount that will fit any quadcopter that has a 32mm spacing back plate and 20 mm high standoffs. was designed for the AOS series of qaud copters but will fit anything that has a back spacing of 32mm. printed with ninja flex…
The original ducts on my HGLRC Moto whoop 90 are made of 'glass' they break at the slightest contact. Drew up some repla
A compact hard case suitable for safely transporting HGLRC Thor Pro 6 parallel charging boards in densely packed FPV backpacks. Based on The Utility Box by Github user dppdppd .
Rekon35 is a cool concept, but I had issues with the battery tray not maintaining contact and the model would reboot mid flight. remix flattens out the battery tray to allow use of the original 2s battery holder as intended and adds…
Should fit any GPS with 21x21mm profile. Does not fit the Source One V5. Printed using 95A TPU filament, 0.2mm layer height, 0.4 nozzle on a prusa mini+. Does not need supports.
Калібр Rama APEX 5 для GPS HGLRC 100pro
You can mount gps either way - there is a dedicated hole for gps wires. V2: further improvements
Here is my gps mount that will fit any quadcopter that has a 32mm spacing back plate and 20 mm high standoffs. was designed for the AOS series of qaud copters but will fit anything that has a back spacing of 32mm. printed with ninja flex…
V2: shortened the holder to not cover the USB port My battery holder for HGLRC draknight broke, so i modeled a stronger one. Optimized to print easyliy without supports or bridges out of TPU. It should be printed on the side. It is made…
Made for this antenna - https://a.aliexpress.com/_EHRjSl6 I printed it from PETG, but you can try print it from TPU or something other I added a little glue between the antenna and the mount to make it sit more securely in place and to…
Speedybee Mario8 HGLRC USB-C Extension for top hex holeSpeedybee Mario8 HGLRC USB-C Extension for top hex hole. Use 2 M2x8 or M2x10 screws for assembly.
I made this case/fender for gps module HGLRC M100 which is atached to Readytosky Johnny 5" V2 drone frame printing: infill: 80% perimeters: 3 filament: eSUN TPU 95A supports: you dont need supports!!
For the iFlight Nazgul XL5 ECO Features: GPS mount for HGLRC M100 GPS ELRS antenna guides Dual SMA mounting bulkheads Vertical XT60 mount I printed mine in TPU with supports only on bridging areas.
HGLRC M100 GPS Mount for RC Planes This is designed for flat mounting the HGLRC M100 GPS in RC planes, using double sided tape or similar. I recommend printing this in TPU. HGLRC M100 GPS Mount for RC Planes: HGLRCM100_GPSMount.stl
This is a antenna mount i designed for the 3.5 inch HGLRC Veyron 35 drone. It is compatible with the SMA antenna mount
Print with TPU and support oriented upright.
mount for an M100 mini gps instead of the M1000
arm guards vor HGLRC Rekon LR4 Frame
Five33 Lightswitch V2 Ultra arm cover with HGLRC LED strip There are 3 versions, a normal cover without LED, one with LED slot for the HGLRC LED, and one with a slit for if you're using an opaque TPU though it will only be visible from…
Addressable 2812, Includes wires
GoPro session 5 mount at 30degree tilt for hglrc sector 5 frame the mount will fit a tbs nd filter Print Settings Rafts: Doesn't Matter Supports: Yes Filament: eSun tpu Category: R/C Vehicles
These are the pieces I designed to add servo-tilting functionality to my HGLRC Veyron35 CR Pusher. I consider it strictly to be a prototype, so for more context on how and why, please watch this YouTube video which explains the reasoning…
Hello This is a mount for the BDR Iris drone : https://rotorbuilds.com/build/27906 It allow to fix: - HGLRC M80 GPS - vifly finder 2 buzzer - Vista antenna mount To be printed in FLEX. Happy flight. Julien
a basic support for any RC fixed wing (A10 Thunderbolt II in my case)
support pour antenne VTX incluant un support pour Buzzer et LED HGLRC
print it in abs , you will need 4 M3 screws and 4 nuts you need to flex the part to put the gps in and then screw it in the frame
Base ajustable pour monter votre Gopro sur le HGLRC Sector 5 v3 . A imprimer en TPU , a la verticale.
AOS UL7 V5 - HGLRC M100 GPS Mount GPS Mount for the HGLRC M100 that slides over the rear standoffs. The standoff tubes are 20mm to match the one I received from IFlight, so I've included a 5mm sleeve/spacer to fill the gap if you aren't…
LiPostrap mount for the HGLRC Ublox M8N GPS Print Settings Printer: Renkforce RF2000 Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: 100% Filament: Renkforce TPU, TPE Notes: I´ve printed this with a 0.8mm nozzle, 2 outer…
I printed them in TPU. 0.2 layer height I used hairspray to make it stick to the glass bed as usual. Print Settings Printer Brand: Creality Printer: Ender-3 S1 Rafts: No Supports: No Resolution: 0.2 Infill: 20 Filament: Saintsmart TPU Red…
The HGLRC RC2 is a clone of the TS100 wih a biggger body. It uses the same tips. The botom part is the same
Single and double antenna mount for the HGLRC Rekon 5. Should/could fit other frames with 4mm standoffs that are 12mm apart (center to center). Made it to fit a single antenna (DJI O3) as well as the double antennas of the DJI O4. Printed…
Battery harness for HGLRC Draknight 2" Toothpick Drone. (Drone) Designed to hold: 450mAh 7.4V 75C 2S LiPo Battery Note : Only the Battery Holder v2 has been flight tested. Printed using 95A shore hardness TPU.
can switch gps holder. just let me know. using tpu 95A
This is a dedicated GPS mount for the HGLRC M100 GPS module , designed for the SpeedyBee Master 5 HD frame. The mount uses a 22 mm mounting hole spacing and is designed to fit directly onto the frame. Features Designed for HGLRC M100 GPS…
Just the original plate without the gopro mount part because i thought its ugly. print in TPU or whatever i dont judge, it has a little bit of mechanical inflence due to 3 Frame Screws going through it so a good amount of infill is…
Darwin Baby Ape HGLRC M100 Mini Holder Halter Kabelführung unterhalb. TPU empfohlen
O3 Air Unit and HGLRC GPS/Mag antenna mounts for Tanq2. The GPS mount fits several antennae including HGLRC M100 and M100-Pro. It is tilted up 45 deg to maximize coverage when actually flying (nose tilted down). Be sure to let Betaflight…
A completely overhauled canopy for the Petrel 132 with a large fin and stronger front mounting
With this backplate the draco ground unit is mountable on this Sky04x Mount: https://www.printables.com/model/854805-skyzone-04x-walksnail-vrx-mount You need a M3x8mm screw
To give space between GPS antenna and FC/VTX I added this GPS mount to the original antenna mount.
Printed with PETG with .1 layer height. The MAG Alignment in Betaflight should be set to CW 90° in the config tab. But also confirm that the compass points the right direction in the setup tab.
V2: shortened the holder to not cover the USB port My battery holder for HGLRC draknight broke, so i modeled a stronger one. Optimized to print easyliy without supports or bridges out of TPU. It should be printed on the side. It is made…
Single and double antenna mount for the HGLRC Rekon 5. Should/could fit other frames with 4mm standoffs that are 12mm apart (center to center). Made it to fit a single antenna (DJI O3) as well as the double antennas of the DJI O4. Printed…
Simple TPU mount. Print top facing side down to avoid overhangs and to get nice surface finish.
GPS mount for HGLRC M100-5883 + Source One V6 Print in TPU. Use 0.2 mm layer height, 30% infill, tree supports ON, build plate only OFF, remove small overhangs OFF.
This is a antenna mount i designed for the 3.5 inch HGLRC Veyron 35 drone. It is compatible with the SMA antenna mount
These propguards are specifically designed for the HGLRC Drashark 1.6-inch quadcopter to protect your propellers and motors from impacts and damage. They provide excellent stability and durability without significantly adding weight to…
- protections bras - support camera nebula pro - support antenne lollipop - protection lipo 6S 1300mah - protection elec stack + vista - top plate avec aileron + logement M10 Mini GPS - FlyFishRC - support XT60 + condo prints en TPU en…
This is a soft mount for a GPS (HGLRC M100). This get's the module far enough away from the motor EMF that the compass can be used for navigation. Included are the GPS holder, rx mounts for a crossfire nano rx antenna, and some soft…
I made this to mount the large capacitor that comes with the Jijie (DakeFPV) H743 stack with 70amp ESC in the HGLRC Rekon 10 Pro frame. There isn't much space in the frame for the capacitor, so a discrete mount was the best solution using…
Created this model to hold the gps antenna for my HGLRC MY7 frame. The antenna i used is the Sologood M10-180C, with a width of 18mm and a heigh of 19mm without the plug. The distance of the fixing screws (holder to frame) is 24mm. I used…
based on the original shape of the OEM part, I wanted to put an SMA antenna on my rekon35 quad.
the existing Gopro mount is a little too small to properly mount a gopro or other action camera.
standoff distance 20 mm hole/standoff diameter 4 mm Print Settings Rafts: Doesn't Matter Supports: Doesn't Matter Infill: 100% Filament: tpu tpu Category: 3D Printing
update 30/09/2022 - updated design of version 1, added version 2 Designed for Alien 5" ReadyToSky frame. I printed it with TPU 95A. Other FPV stuff: Alien 5" GoPro mount Alien 5" action cam mount Alien 5" GPS mount Alien 5" Legs Mobula 6…
A HGLRC pole antenna mount for the Arris 250b frame, for easy unmounting for the caddix vista long range antenna for easy drone storage
I was tired can't carry camera on this little drone so i designed 2S mod to give him more punch. Now i can do mid range fligth carrying insta go or go2. My bottom part is designed for the Mamba F411 25A AIO and the short version of the…
Fixed Mount for GoPro Mini 11 with TBS ND .. for more space für bigger lipospacks. 30 or 35° angle Category: 3D Printing
Hglrc Wind 5 with antenna mount for Rush Tank VTX and camera mount for Foxeer Box 2. Print instructions Unassociated tags: rush tank, wind 5 Category: R/C Vehicles
