Counting matching models…
Credit: Thanks to Lorenzo (@laurent.polese) from MakerWorld for sharing the original design. Modifications made to the original: Printed using a 0.25 mm nozzle for higher detail Buttons scaled to 92% on X and Y axes Buttons scaled to…
Under desk headset holder for Jabra Evolve 40. Mountable with two countersunk srews. Important: Only the button for the busylight can be reached on the USB controller! Printsettings: - Supports - 0,2 mm layer height
E_Tech 14 made an awesome jont fix. I took his design and made it even better.. now it can be printed much easier. The design is also optimized. update: both sides Remix of: https://www.thingiverse.com/thing:4724194
A charging stand for the Jabra Evolve2 65 Headset Designed to hold the USB C cable that comes with the headset. No support material is necessary. Print in the upright orientation. This is a remix from @daRiddler Jabra Evolve2 65 Dock to…
Printable fix for when the Jabra Evolve 65 snaps between the on ear element and the headband. Uses two M4x10 screws to clamp onto the headband and the on ear element slides into the holder. The printed material is thin enough to allow for…
A charging stand for Jabra Evolve 75 wireless headsets. Print settings Material: PETG Layer height: 0.20 mm No supports needed. Materials Anker Powerline Micro USB cable - A8133011 (Other cables probably will not fit) Self-Stick Rubber…
Lightweight stand for the Jabra Speak 510 Printed with 10% infill (and organic support) Pictures are from a testprint in draft mode. --- Leichter Ständer für das Jabra Speak 510 Gedruckt mit 10% Infill (und organischem Support) Die Bilder…
My wife's headset broke off from it's hinge, quite common issue with these. This print works by glueing it onto the speaker, the hinge stays when snapped in place. The speaker is still moving, all the buttons open to reach. I used PLA…
A handy stand to set your Jabra speaker at 60deg on your desk. Improves sound directionality.
Prints fin standing with no support. I used 25% infill. I have not tested this with the Jabra Speak 510, but the dimensions are the same, so it should work. Please comment your results with the 510.
A small holder for a Jabra Speak 510. My wife and I share an office and during conferences, the Jabra projects the sound straight up and around the room. This is distracting for the other. Now we can direct the sound to the person in a…
This is a nomad hook for Jabra headset (Evolve 40 and others models). It screws on a desk, a table or a shelf up to 4cm thick. Ideal when you work on multiple desks. The control module clips in the built-in circle. Voici un crochet nomade…
Here in Sapir College - Israel we have a Call center equipped with some 20 stations with Jabra earphones It seems that these earphones (not cheap) have a serious flaw in design , 50% of the are already broken in the same place, they…
Repair part for broken Jabra Evolve 65 Mono
Jabra Headset Wall Mount Designed for 3.0x12mm screws Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 200 Infill: 20 Filament: Prusament ABS white Notes: surface smoothed with acetone vapor gives a…
Making working from home a bit nicer with less clutter on the desk. This mount allows to stick the headset's remote control under the desk. Print instructions Nothing special. Prints without supports or infills.
sung, minimalist stand for the Jabra Speak 55 LIKE if you like. thanks!
The Jabra evolve 65 is a great headset but finding the micro USB cable all the time to charge it is a little annoying. I created this charging dock/cradle. I have included 3 versions: No boom cutout - you will need to fold up the boom…
This is a cover for the Jabra Elite 7 Pro case (I imagine it would fit the 7 Active too). Easy print in two parts (top and bottom), then use Bi-adhesive tape to fix the case in place. I used thick bi-adhesive tape, so the cover could not…
Missing a proper stand for your Jabra Evolve2 65 Flex that you know and love from other Jabra headsets? This one comes close to that but utilizes a common Qi-Charging pad. The headset “slides” into position and ist perfectly aligned. How…
My Jabra EVOLVE 40 headset breaks on the right "arm", so I created this reinforcement part. It can be used both to reinforce an intact headset or to repair (making it usable) a broken one. To have more stability between the printed part…
It has a tight fit due to the rubber of the Jabra base. The Jabra won't move. The model has two M3.5 screw wholes. Source file can be found at: OnShape Jabra 510 Wall Mount Print instructions Category: Audio Summary It has a tight fit due…
es ist die möglichkeit deien Jabra kopfhörer zu repariren
Charging dock for the Jabra evolve 75. one version uses a magnetic charging cable from AliExpress ( 8mm diameter) to avoid potential damage to the micro USB port. the other version is for the original cable supplied with the headphones…
As I heard about the contest, I thought my other design (Webcam Cover) would fit perfectly into this category. unfortunately I had already published it shortly before the contest begun so I could not use it for the contest. Today I was…
A stand for the Jabra speak 510 the speaker is at a 60-degree angle
Originální ouško moc dobře nedrželo a neustále se vycvakávalo z handsfree. Děkuji za případný like.
Wyoming Satellite based on Jabra 410 and Raspberry Pi Zero 2W This guide explains how to build a Wyoming satellite using a Jabra 410 speakerphone and a Raspberry Pi Zero 2W. Bill of Materials (BOM) Jabra 410 (Jabra 510 should be…
Jabra Talk 45 Earhook printed with PLA Print Settings Printer Brand: FlashForge Printer: Guider II Rafts: No Supports: No Resolution: 0.12 Infill: 100 Filament: PLA eSun Category: DIY
It uses the USB-C cable delivered with the Headset for Charging.
Holder to mount Jabra Speak 710 or similarly sized speaker to a camera mount. Hole is made for standard camera screw (¼"-20) that you will need to tap yourself. Please reach out if there's another mounting type (e.g. fit a camera shoe…
Deutsch: Dieser Stand ist ein Remix des Ständers für das Jabra Evolve2 65 Headset mit mehreren Verbesserungen: Deutsch: Dieser Stand ist ein Remix des Ständers für das Jabra Evolve2 65 Headset mit mehreren Verbesserungen: • Optimierte…
Need your Jabra audio puck mounted on a wall or ceiling? Say no more, got you covered. Enjoy.
Repair rings for Jabra Evolve 65. Does not allow rotation on the headphone.
Headphone holder with place for jabra evolve30's control thingy. (Model w/o the plate attached too.) Holder's inner diameter is 55mm. For table thickness 9-29mm. Printed with Anycubic mega My used print directions are on the attached…
Printed well with no supports. Remixed from: https://www.thingiverse.com/thing:4636844
Could not find one for the Jabra 2 55 here. Fits perfect.
A deskstand for Jabra Evolve2 85 wireless headsets. Print settings Material: PLA or PETG Layer height: 0.20 mm Supports: Yes
I've had the Jabra Evolve2 65 Headset for over 3 years now. Because of daily use the earpads began to desintegrate to the point i had black pieces of the fake leathery fabric sticking to my face on a regular basis. Decided it could no…
Simple holder for headset & remote. The remote slides in smoothly & stays removable. The holder is designed to be affixed with double-sided tape. Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: No Supports: No…
Sometimes this part can break.
Die Jabra Headsets Talk 45 und Stealth kommen mit einem ergonomisch schlecht konstruierten Ohrbügel, der mir nach kürzester Zeit Schmerzen verursacht hat. Darum habe ich mir mit TPU (Willowflex) Ersatzohrbügel gedruckt, die ich auch über…
This is an easy print. You can use draft even and it works out fine. There is a slot to route the cord behind as well so that you can have a pretty clean desk setup.
Snug fit on the two-ear version, resize to -0.5% for the one-ear-version. Supports recommended but not required.
Headset support for Jabra Evolve 20 MS Stereo and control button Additionally required M4 nut and M4 screw (at least 20mm length). I used a DIN316 wing bolt
This model consists of two options to mount a jabra speak to either a desk or a 35mm pole (monitor stand). Other mounting options can easily be made to fit the main jabra holder. The assembly is done with two M3x10 bolts.
There are 5 parts that need to be printed. The "holder" is pushed onto the "clip". Then the "screw" is screwed into the "clip". Finally, the "cap" is screwed onto the "screw" with an M3 countersunk screw (8-18mm long). Everything can be…
Wall Mount for Jabra Speak 510 printed with PETG, 0.2 mm layer height and 4 perimeters. Approx. 2 hours printing time. My Jabra Speak 510 is simply plugged in.
Speaker Base for the Jabra 510 speaker phone. Make sure the microphone is lined up with the bottom cutout. Top cutout is for the USB cord. Printed with fuzzy skin on the outside, lightning infill at 25%, black PLA.
Adapter to Hold the USB Dongle for the Jabra Evolve 65 on the headset. The design is not really evolved and has some shortcomings. Its a 10 minute modeling to solve the "Where is the fr**king dongle again???"-Problem. So it could be…
Print without supports. i did .3 mm with 20% infill since these isn't a part you'll see once installed. You can print the top part twice or pair it with a bottom part to flare the earpads out a bit more, and have a more snug fit. I used…
A holder for Jabra Elite BT earbuds I designed for my Gridfinity charging station. Printed in Prusament Royal Blue PLA with .6 Nozzle. Gridfinity was designed by Zack Freedman.
Case for Jabra Talk 45; I printed in PLA, cap has a good pressure fit on my normal settings. Made a small adjustment so you can also put the cap on the bottom edge when open. But you can also rotate it 90 degrees and snap it to the side.…
Finally it's here! Store your Jabra Link USB adapter in this magnificent cylinder. Knurled surface for both esthetics and function so that the grip is secure when threading the parts together. A beautiful piece of art for your desk that…
it's a tight fit. Could probably do with some cable management but this works for me. Printed with PLA and support on bed for the skadis hooks. If you want to mount it I would recommend to first unwind the cable, mount it and then rewind…
19mm version is for Jabra Evolve 65 and 25mm is generic for other models. Use double-sided tape on non-screw version.
The original model was made for the Jabra Speak 510, but it also fits my Jabra Speak 2, although it's a bit tighter.
Das ist ein Halter für mein Headset (Jabra Evolve 40 MS Duo). Er passt bestimmt auch für andere Modelle, solange die Bedieneinheit die selbe ist. Zur Befestigung sind 4 Löcher vorgesehen für Senkschrauben. ich habe 3,5x16mm verwendet.…
Simple wall mount for Jabra Panacast conference room camera. Design file included so that you can adjust length to suit your wall ←→ TV distance.
Headphone holder for a Jabra headset for my Lenovo L580 laptop. The holder is attached to the right-hand corner of the laptop. Printed with a Prusa Mini+. Support should be activated.
We're using these speakers in our meeting rooms in our office and to prevent theft, we decided to mount them to the table using double sided tape. This mount attaches to the cable loop and locks with a single M3x10-16 screw, so it cannot…
This honeycomb storage wall widget mounts your charging case, leaned gently towards you, ready to grab your headphones, and also provides a convenient window for your charging cord so you can leave the case in the wall when taking your…
Designed a simple holder for the Jabra Elite 75T to fit the Ikea Skadis system. I chose the orientation on print bed the same as later installed. Support needed. Supported areas won't be visible after removal of the supports. If you want…
Friction fit holder for bluetooth headphones
The Jabra Evolve 80 is a very good headphone, but unfortunately its headband is defective from the factory. The material is not elastic enough, so it breaks after 1-2 years of use. I was sorry to throw it away, because otherwise it works…
Ever wanted to get rid of Google Home or Alexa? With Rhasspy (soon integrated with HomeAssistant ) you can create your own "Voice Assistant" which runs in your own home without calling to outside servers to understand you. I'm about to…
A support for your Jabra elite 3 active.
Small 1x2 Holder for my Jabra Earpods No holes No Support 5% Infill (Cubic)
This is a lightweight Jabra Evolve 20 30 hsc016 headset desk holder for those who are mad about this piece jumping off the table 2 variants - one with a holder only from one side and a second with holders from both sides for better…
Looking to get my Jabra speaker off my desk but accessible easily. Couldn't find a mount I liked so I made this one that goes on my dual monitor stand. I used some threaded heat inserts and 3mm allen screws but If you made the holes a bit…
The cutout is the actual size of the case so scale down in your slicer so they don't fall through. I printed at 99.5% and I was satisfied with the fit. Holes are sized for #8 wood screws.
Soporte de mesa para auriculares Jabra HSC040Wa Jabra HSC040Wa Tischständer für Headset
Pouzdro vzniklo kvůli neustálému sundavání náušníku a háčku v kapse, a nechtěnému vyhození z kapsy kapesníkem, nebo třeba klíčemi a následné ztrátě HF. Po dvou ztracených kusech už je klid :) Tisk: vrstva 0.2, infill 25%. Víčko jsem…
This is a remix of the jabra evolve 75 docking station made by BoTa from thingiverse. The wood texture was added with Blender, then printed with ColorFabb Woodfill. This choice of material not only lends an authentic wood-like appearance…
This is a cover I designed for my Jabra Elite 65T after the original case's hinge broke. It keeps the top and bottom halves of the case connected and allows opening and closing just like the original hinge. It also has an opening for the…
Headphone hook for the Fully Jarvis Laminate desk top and Jabra Evolve 40 headset. Category: Office
Da ich es Leid war, immer das Bedienteil suchen zu müssen, wenn ich einen Anruf entgegennehmen musste, habe ich diesen Halter für das Jabra-Bedienteil entworfen. Das Bedienteil lässt sich leicht in die Halterung einlegen und diese kann…
Basic headset hanger for Jabra Evolve 65. Meant to attach to side of modular hanging cabinet. Printed in Atomic PLA. Supports required (base plate only).
When you have issues with elephant feet on the first layers, you might sand the edges othewise the cable might not fit Printed without supports. If you use 50-60% infill plus increase the perimeter, the stand gets more heavy. an. optimum…
The Jabra Evolve2 65 USB adapter can be fixed to the headset Print in TPU no supports needed
Cap fits the screw, if printed with TPU /TPE it protects the office desk from scratching and has a better grip.
Case for Jabra Talk 45 Octagon; I printed in PET, cap has a strong pressure fit on my settings. Took the the Original from @Zeno to get measurement and modified because I am to lacy to take it apart to fit in box. Category: Mobile Phone…
A super simple Jabra 510 mount, allows you to clip it to a 35mm pole/ monitor stand.
A 2x1 Gridfinity storage slot for the Jabra Elite 7 Pro case. This is based on the Gridfinity organization system by Zach Freedman.
At CRASH Space hackerspace in Los Angeles, we use a Jabra speakerphone to host virtual events, and it sounds better if it's lifted off the table a bit. We were using a mason jar of acetone, which was kind of silly, so I designed a simple…
I had no convient place to store the Link-Dongle when it is not in use, so I created a holder, that attaches to the Evolve2 65 Charging Stand. I have created a version for the USB-C variant and also for the USB-A variant. German - Deutsch…
V2 is without the plate for the thread (the white print).
Easy to print, flip it to the side and just print with whatever settings / material you like
Dieser speziell entworfene Halter für den Jabra Speak 510 bietet eine gute möglichkeit den Konferenzlautsprecher nah am Sprecher zu Montieren . Der Halter sollte aus mindestens PETG gedruckt werden um die Stabilität herzustellen Einfache…
Dieser Ständer für den Jabra Speaker2 55 hält den Lautsprecher sicher in Position und erlaubt eine bequeme Bedienung der Tasten. Der Ständer kann ohne Support gedruckt werden!
Feel free to remix it! Comment with your make :D
A desk stand to hold the charging case for the Jabra 65t earphones with usb cable attached. Here is the right angle cable used. It is a tight fit so other cables likely won't work. The part is symmetric so if you get the cable angled the…
Print with brim. Support isn't needed. Screw hole is 3mm.
This is a remix to add slots to install 1/4oz wheel weights to give the dock some more weight. I found the original was so light it wouldn't stay in place on my desk when the headset wasn't on it with a thicker USB cable with some memory…
The IKEA addon can be found here https://www.ikea.com/gb/en/p/micke-add-on-unit-high-white-90180025/ https://www.ikea.com/de/de/p/micke-anbauelement-hoch-weiss-90180025/
This is a remix from https://www.printables.com/model/37092-jabra-510-wall-mount to mount the speaker to the HSW
Wall holder for Jabra Evolve2 75 Wireless Charger
Remix of https://www.printables.com/model/751525 with larger hole for different kind of magnetic USB cable
Jabra Evolve 75 Dock Used materials: PETG Led diffusor printed on Resin printer but can be printed of FDM with clear filament. Face and trim layer height 0.12mm. Used hardware: Screws 2.2 x 7mm - 10pcs, 3M Double sided tape 0.2mm…
