Counting matching models…
Disclaimer: This is not an official model by JGAurora or even based on official measures. All measurements for this model were taken from my JGAurora A5 printhead and may be different on your printer. Before taking this model as a base…
Remix of the CR-10 Vibration Dampers with a smaller diameter of 23mm, matching the rubber feet of the JGAurora A5. Tolerances allow for easy assembling. These PLA vibration dampers help to significantly reduce printer noise, and in my…
JGAurora A5 and A5S Hotend Upgrade D.Drive Dual 5015 Fan Abl Sensor
My Cooling Ducts using Fans 5015 24V https://www.amazon.com/gp/product/B079BPS9Q8/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1 The Hot End Duct ONLY was Remixed (Completely Redrawn) from https://www.thingiverse.com/thing:2994069 Print…
Hot Bed cable chain for JGAurora A5S/A3S Middle part from https://www.thingiverse.com/thing:3954315 Printer: JGAurora A5S Rafts: No Supports: No Resolution: 0.4mm nozzle, 0.15mm layer height Infill: 30% Filament material: PETG Notes: I…
Works well with the vanilla JGAurora A5 hotend , or any of my custom printheads for the JGAurora A5: Vanilla JG A5 hotend with Zesty Nimble Remote Direct Extruder V1.2 E3D V6/Revo Six Hotend with Zesty Nimble Remote Direct Extruder V1.2…
Easy mounted upper support for Z axis JGAURORA A5. The ball bearing 8x7x22 was applied. Solidworks model is attached, you can customize it to any other bearing Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No…
This thing allows to mount a 3D-Touch bed leveling sensor to the side of the printhead. It fixes two major issues I had with other mounts: It does not collide with the frame when moving the Z-gantry all the way up. It avoids long levers…
This is E3D--V6 Hotend Mount for JGAurora A5S (A5). Main Body was remixed from https://www.thingiverse.com/thing:3828989 It was remixed also but it had a Step File that It could be easy to modified. The whole thing can be used in full…
Fan duct and matching fan grille for mounting a fan directly above a MKS GEN_L board. When used with a thin fan (8010), the design fits right inside the JGAurora A5 with enough headroom for the Y-axis gantry to pass over. Required parts:…
My Youtube Test of the Chain Link UPDATE: Add a New Version of the Adapter, Adapter-Lock, Link, Link-Lock, Loop, Last Link . The Older Version was working but it was sagging in the center. This new version will keep that more natural.…
My remixed for my Cooling Setup https://www.thingiverse.com/thing:4553114 This is completely redrawn from his design.... There was a lot of problems that need to be redrawn to make it work for my cooling system..... But can be used on…
It's a fan grid for the front 40x40 mm fan. Enjoy. Category: 3D Printer Parts
The JGAurora (now rebranded JGMaker) A5S is a great printer, and I'm very happy with almost every aspect of it. However, one place where it definitely leaves something to be desired is in the stock part cooling system. While it worked OK…
UPDATE: July 24. 2020 I uploaded Version 4 of the adapter. The reason is that I need to make cut so my new Cooling Fan can fit in home X position. This is an Add on to the Chain Cable from https://www.thingiverse.com/thing:3954315 It…
The Bowden coupler for on the extruder of my jgaurora a5 broke. The original design had m6 and m10 couplers but the jgaurora a5 needed a m8. Print Settings Rafts: Doesn't Matter Supports: No Resolution: 0.2mm Infill: 100% Category: 3D…
This is another version of palstic crimp tipe for JGAURORA A5. The main difference from other models - tube fixed by outside diameter. Installation is simple, disassembling is not necessary. Tube and holder tied up by plastic buckle in…
I really like the design and airflow that I got from the original part, version 2: https://www.thingiverse.com/thing:3943491 However, I found the mount to be really weak and wobbly. The slot holes don't leave much material at the top and…
This brush holder, intended for cleaning the nozzle on the JGaurora a5 (a5s) printer, comes with a START gcode script to position the nozzle conveniently for cleaning with the recommended copper brush from AliExpress:…
This is a Remix of the REmix because there was a STEP file included so was easier to make modification. The original posted had a problem with Z-Axis that wiring would be crashed in the frame when going all the way to 320mm. This Remix of…
Works well with the vanilla JGAurora A5 hotend , or any of my custom printheads for the JGAurora A5: Vanilla JG A5 hotend with Zesty Nimble Remote Direct Extruder V1.2 E3D V6/Revo Six Hotend with Zesty Nimble Remote Direct Extruder V1.2…
JGaurora's Z-axis guide. It reduces Z-axis shake and improves printing quality. Use size 608 bearings.
The A5 is a pretty good printer afterall. A lot of good points and of course some not so good. For me the first one one is the stiffness of the Z grantry. That's less than what we can find on a CR10 or a Tevo tornado and other clones by…
Tool holders that clip into the side of the JGaurora A5/A5S I decided to remix this original design: https://www.thingiverse.com/thing:2953883 I improved the design adding one edge more to the other side of the clip, so the whole piece…
This my 3rd design of this it work great. It connects simply onto the x motor not affecting any of your prints. Unfortunately they way it clamps onto the x motor means that you will loss 8mm of your total hight meaning you can only print…
A better part cooling fan nozzle, since the original one is a piece of crap. I would recommend to use another fan since the original one isn't very strong, but if you want to make the stock fan a little better, you can use this nozzle. I…
It's a remixed part from the JGAurora A5X Bondtech mount by seaspotter https://www.thingiverse.com/thing:3259649 I improved the part so that we can mount the original sensor runout. A PTFE tube is required between the entrance of the…
This design allows to anchor a reverse bowden tube to the frame of the A5. I use it in combination with my Zesty Nimble to JGAurora A5 direct mount . It uses the factory bowden tube coupler, which can be screwed right into the part…
I have recently decided to upgrade my JGAurora A5 printer to Klipper. For this I needed a new mainboard and ended up with the BTT Manta M5P. To mount it I had to create an adaptor plate, I can now screw the plate into the original…
Remixed it to support an inductive sensor. I just cut and pasted the OEM_Inductive mount from the Hero Me Gen5 Suite . Use tree supports. Print at 101% if printing with PETG. Use at your own risk. Never leave the printer unattended while…
This design is intended to mount a Nimble V1.2 to the original A5 printhead. It is not suitable for the newer Nimble V2. The design uses a right-handed nimble . It uses the existing bowden coupler to fasten the adapter to the print head.…
This is my Camera mount using 1/4x20 Screw. So you can mount your own camera mounts. The Camera mounts on Bed Slider. Is modular for easy assemble and Also for easy removal when need to calibrate bed or any other purpose This way it's not…
The Standalone Kit from Rics3D is great but some minor things on the parts I fixed for my needs to improve the Standalone Kit. Modifications are: Feets for the printer base increased the hight by 30mm to improve accessability of the…
UPDATE: I added a Small Parts Drawer that can be used with this Tool Holder. https://www.thingiverse.com/thing:4412920 Update: Added a Allen Wrench Spacer so the Allen Wrench will not fall of. Same With Tool Spacer. Both can be printed…
I created a support to install a cable chain to the XZ Mount of the JGAurora A5X. So you can get rid of flying cables in this nice printer. Just be reminded that the filament runout sensor which is installed by default needs to be taken…
This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/eFQ549H4XJ0 Category: 3D Printing
This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/hio62Q2kG3j Category: 3D Printer Parts
I bought a Bondtech clone from Aliexpress and don't wanted to mount it in the default position like the printer is designed because then the bowden tube is always crossing the X beam. Therefore I designed this adapter to mount the…
This is a re-upload since my original thing got swallowed by Thingiverse! The JGAurora has a 90cm Bowden tube. This is a lot. This thing enables you to mount your extruder to the side of your printer, allowing you to shorten the tube to…
I needed a nozzle wipe brush for the JGAurora A5. It uses replaceable Bambu A1 silicone brushes which are pretty cheap and easy to get. Simply peel and stick. It goes into the bed frame on the left rear and the bed screw goes through the…
I modeled this simple lever (Fusion 360) to install under the screw used as the 'button' for the idler to make compressing the spring easier on the thumb than the raw screw head. Back pressure on the forward screw of the extruder fan…
The original part fan would blow down on the part instead of at the tip of the nozzle. My first print was a benchy and it had terrible overhangs. With the new fan the benchy came out good. Print Settings Rafts: Doesn't Matter Supports:…
My jgaurora a5 arrived with the z couplers broken. Made this work so I could start using the printer. After several days of continuous printing it looks like it can be a permanent fix. The original 8mm nut was to large to fit through the…
You can try to print the box without supports if you think it can handle it Fits over the white rubber the accss file is for a jointed mini octopus wiggles a bit if the printer is shaking too much thus showing you maybe why your last…
![JGAurora A5 E3D drag knife mount [vinyl cutter]](https://media.printables.com/media/prints/220680/images/2169946_a08cad64-b9a9-4156-a081-ea37a210185c/screenshot_20220711_095332.png)
