Counting matching models…
Added 10/11/2025 V3 rim center w/o connector parts (Schraubverbinder) (Felgenschüssel ohne Schraubverbinder) and suitable tire with M3 metric threads. Printing the threads in tpu might fail but then you can just screw them in. Threads for…
Minimalistic replacement for the tiny piece of plastic that holds each earcup of Audio Technica ATH-M50X headphones in place. Note: it's more rigid than the original solution, so headphones are not going to fold as nicely anymore. What…
The original Worx cutting disc size is 145mm, with original blades the full cutting width is 175mm. There are other versions around but mostly for older Landroids. I wanted to create my own and also make some changes to the original…
Small fix preventing ATH-M50X from overextending when small nob is broken normally preventing this. This should be printed in the direction the STLs have to not need support. There is no tolerance between parts to ensure they hold…
Puch M50 Racing scale 1:8 Spoke rim only: without support Supports: Yes Resolution: Dynamic Infill: 50% line Filament brand: 195 - 220 Filament material: PLA
A quick-release clip for the strap that came with the Canon EOS M50. Just push/pull the clip against the metal fixture facing the gap. I recommend printing in PETG or similar at 100% infill, 3 perimeters. The print orientation makes them…
Here is my first post, after 1 year spent with my robot mower, I noticed that the wheel at the front deserved to be improved. So I tried to raise it and widen it. it is therefore suitable for the Landroid M500+ WR165E series . Print in…
!!! The use of the parts is on your own risk, no liability for injury or damage. !!! Custom knife plate for Worx Landroid M500 (WR165E, model 2020) with 5 blades. Can be used on all cut height settings. After printing of the plate part,…
I got a request from Neistsch to modifying my existing thing to fit the Worx Landgroid M500 series, so over a week or so of emailing measurements, images, test parts etc. we finally got the wheel fitted and adjusted to work. The images…
(19.07.2021) update : added a 35mm stand receiver This is a remix from the amazing idea of Alexandre Valentim on Focuspulleratwork forum to have an easy way of organizing and storing wcu rings on your focus station. I've modified the…
Update: bei den Teckerreifen 5 gibt es jetzt eine linke und rechte Version. there is now a left and right version of the Teckerreifen 5. Hallo, ich habe uns ein Rad und separate Reifen konstruiert. Du brauchst dann in Zukunft nur noch den…
PLA flash difusser, uses existing hot shoe mount allow for normal flash deployment
Spoiler für Worx WR165E M500 mit Batteriefach. Der Spoiler wird hinten auf das Batteriefach geklebt. Ich hab es mit Heißkleber gemacht. Der Knopf für das Fach ist immernoch erreichbar mit einem schmalen Gegenstand. Der Spoiler hat nur…
Replacement hinge for the audiotechnica m50x. This part has been modeled for the left side, just mirror the part to have the right side. To replace this part follow this guide from step 5 to step 13 while skipping step 10, and just…
The original clips to hold the filter closed broke, so I designed a 3d printable replacement. It's a pretty tight fit, you may have to upscale it in the slicer a couple percent if it's too tight for you. It has a notch so it clips in…
Adapter to mount cameras w/ EF-M (EOS M50 in this case) bodies to telescopes that use 1.25" eyepieces for prime focus astrophotography. I'm sure “proper” products exist from telescope suppliers, but what fun would that be. Supports will…
UPDATE : You can now purchase an improved version of this prop from Blue Robotics! Users should note that this version is slightly larger, and can cause the M500 to draw more than 40A, above the rated current for the motor. This makes…
Since there are 3 original lenses for this camera and each one has a different diameter (49, 52 and 55mm), I bought all the 55mm accessories and a set of conversion rings for that size. For the last article, I made a sun hood and a set of…
Made a housing to fit an m50 ECU for my speeduino. Requires 4 flathead screws to hold cover in place.
A dust extraction nozzle for Makita multitool (DTM50Z). Has the same size outlet pipe as their 18V router, or the other dust extraction nozzle I've made. Best to print in something like Nylon/CF I think. Messy design I'm afraid, but I…
This is a replacement for the original rubber sleeve on the front wheel. It seems to improve the maneuverability and therefore gets less stuck. Printed on a resin printer (ABS Like Resin) but FDM prints will work just as good.
Felge für Worx Landroid M500 WR164E Den Reifen habe ich vom User Daniel übernommen ---->>> Download WICHTIG!!!! Der Reifen MUSS auf 98% der Ursprünglichen Größe gedruckt werden sonst passt er nicht auf die Felge!!!!! Link zum Spoiler
Canon M50/M50 II grip. This model supports cold-shoe for microphone as well as 3 wood inserts for additional accessories. Wood inserts should be preheated before screwing them in. Compatibile screws: https://www.ebay.com/itm/394487998885…
Hallo, ich habe einen Schutz für das Vorderrad von einem Landroid M500 konstruiert. Der Landroid wir vorne 6mm höher. Ich habe es mit TPU (Extrudr Flex Medium A98) gedruckt. Ohne Infill, mit Wandstärken 5. Viel Spass damit! Hello, I have…
Cuscinetti lineari serie lunga LM6LUU - LM8LUU - LME10UU - LM12LUU - LM16LUU - LM20LUU - LM25LUU - LM30LUU - LM40LUU - LM50LUU. Creati con solidworks con passaggio semplificato. per le misure complete consultare il file inallegato LM_LUU…
Gridfinity bin for Canon m50 It has a small shallow side compartment, happens to hold 5 batteries 3x2x13 for the bin size (non-stacking). The original I printed did not fit very well so I sanded some sides then adjusted the model I…
¼ npt port added for turbo feed.
Hinge fix for Audio Technica ATH-M50X headphones I recommend rotating 33° on X and Y axis, and sinking the model little bit for better adhesion Depending on tolerances of your printer, set the scale to 108% on X axis and 104% on Z axis…
Hier haben wir einen Spoiler für den Worx Landroid. Passend für alle Größen wie M500, M700 oder M1000. Ich habe den Flügel in PLA-Orange und die Halter in schwarzem PLA gedruckt, hält schon den ganzen Sommer und verformt sich nichts. Ich…
osVAC neo M50 + step + Fusion 360 I did bring osVAC to Fusion 360. The link to the latest version of the files can be found here: Ich habe osVAC in Fusion 360 nachgebaut. Der Verweis auf die immer aktuellste Version ist hier:…
My hinge broke so I modeled this as a fix. I printed it with PLA since that's all I have, and it's been two weeks so far and it's holding strong. I printed it vertically, the same way the 3D model is oriented. Supports are required, so…
I just wanted to make my M30x immortal so yeah I tried printing this out of a bunch of different filaments but I found that PETG is the best material for it. So far I tried random PLA+s, ABS+s and PETGs Most PLA+ lasts around a month,…
This Gridfinity-compatible 5x3 bin is designed to keep your Canon EOS M50 and its essential accessories perfectly organized. Features: Canon EOS M50 Slot : Custom compartment for the Canon EOS M50 body with the 32mm EF-M lens attached ,…
Project developed thanks to Canon M50 CAD files, created by Luke Pamula Parts List DR-E12 DC Coupler for Canon M3x10 Screws - 5 pcs M3x5x4 Insert Nuts - 5 pcs 1/4-20x8x8 UNC Insert 1/4" UNC (20)x3/4" (19mm) ANSI 18.2.1 (DIN 933) Screw 2S…
This is a project that I have spent around 100 hours on. It holds a 10x6mm 2 axis bubble level and the below stated microphone. https://smallrig.com/simorr-wave-s1-lite-compact-on-camera-microphone-3452.html Mount the rig with the hot…
M50x1.5 threaded blind stuffing to close unused M50-openings. Unused PG42-openings in housings are also possible to close with this blind-stuffing set. [1] Thread type: Metric tread [2] Diameters for suitable openings: Diameters for…
Canon M50 Stock Len's Cap holder for Stock Lens 15-45mm. Will not drop or lost your Len's cap again! Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No Resolution: 0.2mm Infill: 80 Filament: Any PLA Brand…
No supports needed. 1x1 Gridfinity Tiles. Video about cool Gridfinity drawer solution on my channel: https://www.youtube.com/@luisengineering
English: osVac adapter for the Blastgate ( https://www.thingiverse.com/thing:4790129 ) or other Blastgates with a M50x2 thread. Actually, the heel, for which the support is also needed, should seal. If not, simply Teflon tape ca.10 times…
Adapter to mount cameras w/ EF-M (EOS M50 in this case) bodies to telescopes that use 2" focusers for prime focus astrophotography. I know “proper” products exist from telescope suppliers, but what fun would that be. I didn't need…
I tried out many different concepts from the internet but none of them was suitable for my machine. So I designed a system from scratch and am very happy with it, feel free to modify it ( .f3d and .step files are included). Please tell me…
I ordered a bleed kit for my Shimano hydraulic brakes. I didnt know I needed the extended kit so the brake oil container adapter was missing. So I printed my own, which is a fraction in size compared to the official one and it works like…
This is a replica of Tektronix part number 214-1593-02 which is no longer available. This barrier key snaps onto the EDAC card edge connector that is used in TM500 series power supplies. It prevents incompatible plugins from being…
I was tired of having the extra batteries for my Sony A77ii getting lost in my camera bag. This holder keeps my 3 spare batteries together for easier access. Also, putting charged batteries with the contacts facing down and putting spent…
Extended the neck of the drum by 55mm. This works with the SBF and SBL2.0, and does fit with a bit of persuasion into the FDL not sure what other blasters this will work with. If you test it in your blaster, could you comment down below…
Is printed in two parts which need to be super glued together. No brim or support needed. Printed in PLA.
Earcups are too close for my ears, and it gets painful to listen for a long time, so I made a solution for us to use. The design is symmetric for both earcups. Took me 3 tries to find out the best way to print this, 2nd picture shows the…
The laser plates for AtomStack does have different dimension. With this adapter it is possible to use the AtomStack M50 laser in the base plate from the AtomStack R30 and AtomStack R30v2 without replacing the laser plate. Printed in PLA…
Puch m50 (racing or comparable) brake pedal bushing I have not yet tested the durability of this 3d printable replacement. However the part fits snugly and should be 1:1 with the factory nylon bushings. Feel free to use this part for…
An 8 mm thick M50x2 nut for locking the drain of your bathtub in place. I visited several stores asking for a replacement part but they said I had to buy a complete drain set. And I wasn't going to do that. And now you don't either. 0.2mm…
This remix is based on Arduino Nano Screw Terminal DIN Rail mount design by Madhulk, because this design fits very well. This is an adaptation for mounting the ST-M5045 driver to a DIN rail. I use Fusion 360 to adapt it. You will need two…
Print 2 pieces for assembly Allows the use of thinner old style m50 dipstick on a M54 style sump. Printed mine in PLA and smeared RTV on the outside lip. Use original o-rings Has held up fine so far for me but your mileage may vary.
I recently bought myself a device to track stars (Omegon Montierung Mini Track LX3). So now I had the problem with my Canon EOS M50, that it only has a wireless remote (optional), but not a plug to plug one in with a cable to shoot…
A simple stand suitable for GHB SM50B baby monitors.
One of the best headphones you can buy for under £200 is the Japanese-designed audio-technica M50x's. They are meant for studio sound monitoring and have a flat response to provide true to life sound. However they don't have a built in…
This is an updated version of the battery holder for NP-FM500H batteries that I designed previously here: https://www.printables.com/model/449469-np-fm500h-battery-holder The previous version lost its grip on the batteries over time. So I…
Support de filtre pour aspirateur Dirt Devil Infinity Excell M5050-5
3D model of a bicycle mount designed for the Fenix HM50R V2.0 flashlight. The mount allows stable and secure attachment of the flashlight to a bicycle handlebar and is intended for 3D printing.
I had a problem on my bike when my chain from time to time fell off during landings. So I have utilized mounting holes on my Bafang M500 engine to design a simple chain protector. It is held in place by 2 M4x12 screws. I have printed it…
Audio-Technica ATH-M50x - Repair & Preventative Reinforcement Clip (No Glue - Snap Fit) Project Description Has the curved yoke of your beloved Audio-Technica ATH-M50x broken, or do you want to make sure it never does? A quick internet…
Here's the Onshape document in case you want to modify it https://cad.onshape.com/documents/32d1579a603f01bd53151d12/w/b756d6f6f3859f4349c47e6e/e/793c51763f7b6c1e29ff648d?renderMode=0&uiState=650f29affb883d54e0d0287d
I bought a new Atomstack M50 laser (10W) which works great. However, my existing Air Assist came with a shorter window. This extension blocks the empty space, so the laser light won't come flying out the top, and the laser+fan assembly…
Has clearance to open the battery bay for the Canon m50/mkII.
A End Piece for a trottlecable of the BMW M50 Throttlecable. Fits Perfect for Schassis. (made it for my S14) Should fit in various nissans or custom builds. 7mm bowden. 15mm Hole. No supports needed.
Might need to drill the hole to 3.15 - 3.2 mm.
Laser-cut insulator panel and 3d printed brackets for TM501 power supply based on the existing design by NFM.
We are using Axis M5074/M5054 and M5054/M5055 camera underground where they can be exposed to water, this mount will prevent water ingress from the back. Can either be mounted on standard Unistrut or for less permanent install there is…
M503 DRO Sensor Bracket for Felder K700 Flip Stop
🛠 About This Model This is a simple protective frame designed for the Worx Landroid M500 Plus (and possibly other Landroid models) to help prevent accidental pressing of the stop button—especially when the robot moves under objects like…
This replaces the mechanism of a tm500 door handle for RV cargo handle measuring 5" by 4.5". (Might fit others too) Original part are 3 white prongs with snap in/friction connection. I couldn't find the replacement part alone nor a seller…
“The ProSensor M50 has 5 precision sensors"… What it doesn't have is a place to call home - so I threw this together so I can mount it on my garage door for easy to access when needed. Mounts with 2 screws. Filament: ~16g Print Time:…
The shirt clip on the in-line remote for my aftermarket ATH-M50x boom microphone broke, so I modeled this replacement in FreeCAD. Mine was bought many years ago and branded “Neomusicia”, but the design looks identical to the one in the…
Puch m50 Chrome Shock Cover Adapter This part has been on my M50 for 1000km already and has been rock solid. Some sort of adhesive/glue is required for permanent installation (I used Polyutherane adhesive, the kind that foams up) I used…
Puch m50 (racing or comparable) pedal axle bushing I have not yet tested the durability of this 3d printable replacement. However the part fits snugly and should be 1:1 with the factory nylon bushings. Feel free to use this part for…
The motor broke on my cyberbike. Turns out you need some special tools to swap it out. This design is the tool to properly remove the nut that holds the sprocket mount. Note you also need a crank puller to remove the crank arms. This is…
A fully printed headphone holder that will fit desks up to 2.25" thick. No hardware required. Was designed around the Audio Technica ATH-M50x headphones, so any pair with a wider headband probably will not work very well.
Spray head for M50 can. Come with two version : Straight and 25 degree head. Print specification: You should place print position as i show in picture for best result. Infill : 15% (recommend for light weight) Support : Normal or tree is…
Leica wanted to charge me a small fortune for a darkfield slider, so I made my own. This darkfield patch slots directly into the Leica Slotted Abbe Condenser (Leica Part Number: 13 613 550) common to the Leica DM500 and DM750 microscopes,…
Included one STL file. Prints without supports.
skinny holder for a tektronix plug (AM503 current amp is what I use it with, but any TM500 module ( http://www.barrytech.com/tektronix/tektm500/tektm500.html ) should work. I don't have the tektronix power supply where this TM500 plugs go…
Awesome Puch M50 Racing Keychain. Model Commision done by: https://www.thingiverse.com/googoldead/designs
reproduction of 10mm dust cover for mil spec connectors
This is my simple solution to making my ZMF ATH-M50xBT2 earpads fit nicely. I bought ZMF's earpads for my headphones and they feel amazing. However, they are very loose and would constantly fall of if not handled gently. These holders fit…
The Tektronix TM500 is a modular test equipment system offering a variety of plug-in modules that fit a dedicated series of mainframes with one to six module slots. This is a blank panel cover for one of its 6 open bays. The inset on the…
Zodiac M5036 channel selector knob Category: 3D Printing
Die Box sorgt dafür, dass der Handmixer ein ordentliches Zuhause in der Schublade findet. The box ensures that the hand mixer has a proper home in the drawer.
Print with PET-G without supports.
Made this because the glue kept wearing out. I printed it with columns. To attach, put the clasp that came with the ModMic into the circular indent and snap the whole thing onto the headphones. Like this:
Felge mit Hinterschnitt, damit diese auf den M500 bzw. M500 Plus passt. Räder werden vom original Ersteller verwendet und funktionieren super. Wegen der Radgröße ist eine kleine Änderung am Gehäuse des Worx notwendig. Fällt aber kaum auf…
Had the original break on me so I made it thicker.
Battery Charger Stand NP-F550 F750 F 950 FM50 FM500 Battery charger Gridfinity stand. Added Hull Line Remover Space Print with PLA, PETG any speed, I added Hull line remove Space
Heyhooo This is a shock absorber I designed for the Petromax LM500 . https://www.youtube.com/shorts/hlhutxKBYMc The Problem Quite soft impacts from the direction of the battery axes are enough to temporarily disconnect the power supply.…
This is a replacement Z limit switch holder for the M505-B. The thicker block replaces the front switch holder which was previously too thin to accurately activate the switch when the carriage came down. The back piece (the thinner one)…
I got tired of fatigue on the top of my head when using my headphones for long periods so I created these comfort pads for Audio Technica ATH-M50. They might also work for other brands if they are the same width (or you can possible scale…
Important Disclaimer: This is NOT INTENDED TO PERMANENTLY REPLACE A PROPER METAL TOOL, however, it works under reasonable loads and is dramatically cheaper to print when compared to purchasing the suppliers specialty tool. Your mileage…
A spacer that goes inside the earcups/pads of ATX-M50x headphones. With the some pads, ears touch the inside of the ear cup, this lifts the pad away from the body/driver of the headphones and gives some space, making them more…
