Counting matching models…
This is a remixed version of the Kingroon model that works better for the E3D Volcano (instead of E3D V6) and includes an adapter mount for the Makergear M2. I was able to get the original model working, but I lost 30mm of my X-axis. This…
A BLTouch adapter plate designed specifically for MakerGear M2 Rev G and ANTCLABS BLTouch V3.1 (#ad). This design is part of my SKR 2 mod for MakerGear M2 Rev G. The M2 has been the absolute workhorse for me and I love it very much ever…
For nice, sharp prints, you can't beat a blower (rather than a fan) with a duct focusing the air right on the nozzle. This version uses a 50mm x 15mm blower to replace the fan that blows on the part and includes brackets for attaching to…
If you have Simplify 3D and a MakerGear M2, here are optimized profiles that have quality without being slow. I recommend the 0.2mm profile most of the time. Turn support on if you need it. Use ABS juice or (I prefer) Elmer's Glue stick…
Extended Spool holder for the Makergear M2 printer. This is a .95" lengthened version of the original holder. Category: 3D Printer Accessories
Decided it was time to update my old workhorse the MakerGear M2. This mount allows the addition of a BLTouch sensor without loosing too much useable bed space. I'm running this with Marlin 2.1.2 and here's a link to my config files.…
I found the factory cooling angle to be poor and it actually would cool my nozzle as it kicked on. I wanted to better aim the air flow to just below the nozzle. This is a remixed 3MF file which does just that.
In Prusa Slicer, I modified this thingiverse bondtech conversion for the makergear, as the only issue I've had with my machines are the lackluster extruder. Additional shaving off a few mm of the wire harness plastic so it will clear the…
I designed these to go with my flexible build plate from Wham Bam Systems. They definitely fit the M2. I am not sure about the M3 and others. If you can verify the fit for other printers, let me know in the comments.…
There are a lot of alternative hot-end fan mounts for the MakerGear M2 that try to increase airflow where it counts, but most of them require a modified mounting assembly for the hot end. This one goes on just like the standard mount --…
This is a conversion to run the Makergear M3 cooler setup on an M2 with a V4 nozzle. This was designed to use the stock 50mm bed fan of the M2 though so the SE Cooling Duct.STL has to be enlarged to 126% in your slicer before printing.…
i did not design this. a friend made it for me before i learned CAD. iv asked him if i can share, he said go for it... enjoy! almost bolt on no modification,, you may need to add some hardware of take some away,,, works very well. edit: i…
I took a webcam mount I had found for my Ender 3 and modified it to work on the MakerGear M2. I made it so it attached to a modified MakerGear Tool holder. I also modeled a universal camera bracket as the original was designed for the ONN…
This filament path was designed for reliable feeding and for a v6 E3D. Updated for 2019 to be more rigid and to allow for use of two 3mm brass inserts to put in screw to make hot-end be fixed in place more solidly.…
I had an issue with the MakerGear M2 filament drive where it would sometimes jam in such a way as to "lock" the hotend into the groove mount, forcing me to practically break the filament drive to get it unjammed. I split the design into…
Enhanced with the following: Changed ID to be a press fit to this collar: http://www.amazon.com/gp/product/B000P0QAG8/ref=oh_details_o05_s00_i00?ie=UTF8&psc=1 Changed "M2" engraving to an arrow pointer to better show orientation. Added…
This is a remix of the rsilvers E3D v5 filament drive. Provisions have been made for the PTFE tube and Bowden connector on the 1.75mm universal hotend. Category: 3D Printer Parts
This extruder is about 211 grams without the part cooling fan but with the extruder cooler. The respective parts on an M2 are about 248 grams. Ideally print in a stiff high-temp material such as car-fiber filled Nylon. PLA will not work.
I use Octoprint to control one of my Makergear M2 printers but I also like to do a little RetroPi Gaming now and then so I made this quick release mount for my printer so I can quickly remove the Pi when I want to play some Super Mario…
When you get the dual extruder kit for the Makergear M2 you replace the X axis belt clamp. The stock design gives you a X home position which is about 5mm off the left side of the bed. I took the stock design and extended it by 6mm so X…
Camera mount for the MakerGear M2. It snaps onto the right side and should work with most webcams. I use the Logitech HD Pro Webcam C920. You will need one 3/4 inch long 1/4-20 screw. Here is a video from the mounted camera: Category: 3D…
This is a modified spring loaded hinged version of the original V4 Filament Drive for the Makergear M2. My original drive (printed in PETG) wore out (the springiness of the tension of the bottom of the drive) so I designed this hinged…
Remix of Hockenmaiers M2 Filament guide. I used his guide for a while but it does not feed well with the larger than stock guide tube. I only use the middle hole, so removed the others and clipped off the end. I also completely redid the…
simple dial for makergear M2. roughly 6mm inside diameter I printed at 30% infill with 3 wall all around fits good as is but would recomend heating the end up slightly before attaching the dial for best fit.
Added a Palette to the side of my Makergear M2 and had to remove my tool holder. Designed this so I could mount my tools below the Palette 2. Used an existing unused hole in the side of my Makergear M2.
MakerGear M2 BIQU H2 V2 Extruder Mount and Klipper config file. Note that this will limit the X-axis to 188mm of usable space, and the Z to 185mm. I will probably change the part fan to be like the Ender 3 S1-Pro type. Category: 3D…
my coin for mg owners club contest. it was designed to be a pause print then add inner piece... inner piece spins. Category: 3D Printing
Thing 53870 works great to get at the top of the screw adjusting the Z zero point, but that wasn't our problem. We have the locking nut also on top of the Z plate, and it's quite difficult to get at that to unlock the screw. This…
Back in 2012 I built a MakerGear RepRap Prusa i2 and three years late the idler block broke! I made a new one, and here it is. I'm reasonable sure no more than one other person might need this, but it's here for you if you do. This was…
Cricut Cutting Blade Attachment for the Makergear M2 First the Disclaimer........ This is a work in progress (I am uploading this per request.) This attachment is NOT for the average user. It requires advanced knowledge of the M2 printer…
The filament spool mount on the MakerGear M2 works great -- if you have the thick-edge spools like MakerGear uses. For other spools, the mod suggested by http://www.thingiverse.com/thing:37210 works way better (and both can be mounted…
The 3mf files has everything you need. Set up to print on a Makergear M2. I use real screws and nuts to hold it together, I left the 3dpritned ones in the file incase you don't have real ones (which work better). Model has too much play…
Like the title says, this is a trivial, overly simplified, print-in-one-piece-without-support (but with a span), model of a MakerGear M2 suitable as a Christmas tree ornament. Scaled down slightly, could also serve as a keychain. 2014 is…
I remixed this from my previous MakerGear M2 C270 mount for the bed. I made it for my MakerGear M2 Rev G purchased in 2019. I decided to move the webcam mount out from the bed to the printer chassis because I'm planning on modding my M2…
Dial indicator mount for precision leveling the bed on a Makergear M2. (For use with the V4 extruder.) To use remove your filament drive and bolt this on with 4 M3x8mm bolts. Category: 3D Printer Accessories
This is a drawing attachment for the Makergear M2 Printer. First the Disclaimer........ ** This is a work in progress ** (I am uploading this per request.) ** This attachment is NOT for the average user. It requires advanced knowledge of…
Yet another tool holder for the Makergear M2. I run a Sealed Filament Tub on the left side of my printer so I couldn't really use the other tool holder listed on Thingiverse so I came up with this one. It holds the tools included with the…
This bracket allows a $6 webcam to be very inobtrusively mounted on a MakerGear M2 to provide a (low resolution) live video feed of the part being printed. There are two versions here. The original (black, part.stl) version had to be…
This is a duct for the Makergear M2 that has much better cooling behind the nozzle compared to the original fan. It is designed for a Delta 5015 blower (BUB0524HHB) but may work with other 5015 fans. It is mounted using the touch probe…
Modified tool arm that connects to the MakerGear M2 tool holder modeled by Myt3chguru. https://www.printables.com/model/ The model was adapted to strengthen the camera arm and allow for a Logitech C270 to attach to it, similar to how they…
Made to fit on the Makergear M2 Z axis threaded rod. This will fit the locking ring the original z adjustment knob uses. Needed a smaller knob with the extruder I installed. The original knob would contact the new extruder setup I…
Made to fit on the Makergear M2 Z axis threaded rod. This will fit the locking ring the original z adjustment knob uses. Needed a smaller knob with the extruder I installed. The original knob would contact the new extruder setup I…
Modified tool arm that connects to the MakerGear M2 tool holder modeled by Myt3chguru. https://www.printables.com/model/ The model was adapted to strengthen the camera arm and allow for a Logitech C270 to attach to it, similar to how they…
