30 models
A cheap and simple way to remove receptable terminals from a molex microfit 3.0 pin. Usually, you need a special tool from Molex , but a stapler does the job just fine. One side takes two staplers (DIN 24/6), one takes a single one. The…
Keystone inserts for 2-pin MicroFit 3.0 to get GND and 12V from powering Stealtmax from the printer. There is also 3-pin version in case you want to get GND, 12V and 5V for Stealtmax. MicroFit connector is secured in the keystone using…
I could not find any skirt inserts for 2-pin MicroFit 3.0 to get 24V from the printer to ERCF board so I created this remix for 2, 3, 4, 5, 6, 2x2, 2x3, 2x4, 2x5 and 2x6 pins MicroFit connectors in case anyone need them. The lock file was…
This assembly takes two microfit connectors and contains clips to keep them latched to the mating connectors on a BC-250 computer. Prints without supports and tested in PETG. From user feedback, an outer brim and slower print speeds (at…
Update: the original file may appear at 10x scale in your slicer. I've uploaded a .3mf with the correct scaling but you can also just set your scale to 0.10. The correct scaled height is 14mm. The Bambu X1 and P1P have a 4 pin connector…
This mod allows you to replace the original carbon filter, but let's you have up to 5 umbilical cables through the back of your printer. The design allows you to have a clean wiring inside the chamber and let's you manage all the CAN…
This is intended to be a stop-gap solution for someone (like me) who is too impatient for their proper Molex connectors to arrive! As always please take care when printing for electrical connections such as this and make sure that your…
The Molex MicroFit 3.0 connector is really really handy because you can actually crimp it reasonably well on a normal crimper, it's beefy, it's sturdy, and it's able to handle some decent power. The 43650-xx00 parts are designed to be…
Slips right over your Molex Microfit 2x2 to keep your crimped ends a bit more secure. One small ziptie to hold the wire down.
A simple clip/holder for the micro-fit 3.0 power connectors on the bc250. First time 3d modeling or posting here so it's not the best but it works. I'm fairly sure no one else has made this, so here's a simple clip/holder for the microfit…
Insert for Molex Microfit 3.0 2x2.
I bought the Jrready Molex Microfit tools for working on ma Voron printer. I liked the idea to create a case like kyleisah did. But his case is a little to tall in my opinion. I think that is because of the minimum height of the rugged…
Replaces the 2pin Molex (for switch) with a 3pin Molex (for encoder)
When I needed to mount some Molex MicroFits I came here.....but the only thing I found were jury-rigged solutions that included a retaining screw on the back. I have been accused of being fussy before... and when dealing with expensive…
Big thanks to Jevermeister for providing a step file which meant I was able to add a microfit holder to this item. I had to file down the Microfit mount to fit the plug, I see this as a positive as it can be fine turned for maximum grip…
An XT30(2+2) for compatibility with ERCF/SB2209 canbus cable, two microfits for EBB36 and AFC-Lite wiring order.
Just a simple cutout in the rear skirt to allow a microfit panel plug. I've added a 4 pin and 2 pin version but have only printed and confirmed the 4 pin to fit. With the Fabreeko carbon filter you need to get fan wires under the deck…
A Molex Microfit 3.0 4x2 Insert for the "VORON 2.4 SKIRT CONNECTOR INSERT" Model from 3DPrintDemon
This is a 1x4 Gridfinity bin to store two JRready DA Removal Tool Ser-B depinning tools. They have raised icons indicating plug or socket and a layer change, mmu, or sharpie can make them easier to read. The icons were enlarged for the…
Remixed it to add a molex microfit 2 pin connector
This is an 'Overmold' style strain relief for 14 and 16 pin microfit connectors, commonly used for umbilical and FYSETC Catalyst toolhead PCBs. Use the 14 pin for common Umbilical (i.e. LDO), and the 16 pin one specific to Catalyst V1.…
I couldn't find an existing mount for the connector, so I made my own version. It is not perfect, which is why I added a plate on the back that secures the connector from falling out when inserting the male end. The backplate does not…
modified prusa original part for holding 2 microfit connectors used with e3d revo hotend it hold microfit connectors so no more revo heater core wires damage due to wires moving
I made this cap/protector that is held in place by 1in/25mm velcro strap on a LiPo pack. I prevents the balance connector (Microfit 3.0, 16P) from dangling and getting snagged when not in use. This is perfect for RC helicopter (true) 12S…
I wanted to provide a 3.3V pin input to the ERCF v1.1 microfit connector, so I modified the existing design to accommodate a Molex MicroFit 3.0 6-pin connector instead of the original 5-pin connector.
My friend ask for it.
I wanted to provide a 3.3V pin input to the ERCF v1.1 microfit connector, so I modified the existing design to accommodate a Molex MicroFit 3.0 6-pin connector instead of the original 5-pin connector.
This mod allows you to replace the original carbon filter, but let's you have up to 5 umbilical cables through the back of your printer. The design allows you to have a clean wiring inside the chamber and let's you manage all the CAN…
I made this cap/protector that is held in place by 1in/25mm velcro strap on a LiPo pack. I prevents the balance connector (Microfit 3.0, 16P) from dangling and getting snagged when not in use. This is perfect for RC helicopter (true) 12S…
When I needed to mount some Molex MicroFits I came here.....but the only thing I found were jury-rigged solutions that included a retaining screw on the back. I have been accused of being fussy before... and when dealing with expensive…
